Summary of Contents for Gyration DE02559-001
-
Page 1: De02559-001
Gyration, Inc. DE02559-001 Revision 1.0A DRAFT Product Specification RF-only Transceiver Dongle (in GyroTransport plastic) Page 1 of 1... -
Page 2: Table Of Contents
Gyration, Inc. Table of Contents DE02559-001..............................1 REVISION 1.0 DRAFT ..........................1 PRODUCT SPECIFICATION ........................1 RF-ONLY TRANSCEIVER DONGLE .....................1 (IN GYROTRANSPORT PLASTIC) ......................1 INTRODUCTION ..........................4 .........................4 EFERENCED OCUMENTS TRANSCEIVER EXTERNAL CONTROLS AND DISPLAYS ............5 “C ” ( ) ..................5 ONNECT MOMENTARY PUSH BUTTON “S... - Page 3 Gyration, Inc........................10 URRENT ONSUMPTION ....................10 ADIO REQUENCY PECIFICATIONS ENVIRONMENTAL RATINGS AND RELIABILITY TEST ............11 ......................11 NVIRONMENTAL ARAMETERS [A] .......................11 ELIABILITY RITERIA (ESD) R ..............11 LECTROSTATIC ISCHARGE EQUIREMENTS COMPLIANCE...........................12 TESTING.............................12 ..................12 UALIFICATION ELIABILITY ESTING ........................12 RODUCTION ESTING ........................12 AMPLING ESTING PACKAGING REQUIREMENTS....................13...
-
Page 4: Introduction
This document is the specification for the RF-only Transceiver dongle, built in GyroTransport plastic. This design is based off of the hardware design of the Gyration “Gen II” receiver but is placed in the small form factor of the GyroTransport transceiver. -
Page 5: Transceiver External Controls And Displays
Gyration, Inc. 2 Transceiver External Controls and Displays 2.1 “Connect” (momentary push button) For engineering use only; not installed for production. “Status” (LED, orange) The LED indicates when there is radio traffic on this device. 3 Physical / Mechanical External – Plastic assembly For reference only –... -
Page 6: Functionality - Transceiver
6 inches and could be fully adjustable in firmware for any application. The actual distance may vary based on the user’s position relative to the computer. The transceiver also has the capability to bind using the standard Gyration “connect” button method where a connect button on each of the connecting devices is pressed to initiate and complete a bind sequence. -
Page 7: Multiple Transceivers In A System
When in a Dell XPS2010 system (Greenland with an internal daughter card) 4.6 Compatibility matrix with Gyration products This is a matrix that describes the compatibility of this proximity-bind RF-only transceiver with all other Gyration products. -
Page 8: Windows Media Player Software Service Application
USB operation of the transceiver. The transceiver would take that information and send it via the Gyration RF link to the attached MusicLCD remote and then would be displayed on the LCD screen of the remote. This information is only intended for the Gyration / Dell products that support the Music LCD. -
Page 9: Specifications
Gyration, Inc. 6 Specifications 6.1 Material The following materials are to be used for the product: Part(s) Material Color Printed circuit board (PCB) Green 6.2 Labels and Graphics The following labels and graphics shall be applied to the product: Name of... -
Page 10: Absolute Minimum/Maximum Parameters
Gyration, Inc. 6.4 Absolute Minimum/Maximum Parameters Description Symbol Units Supply Voltage +5.0V Volts 6.5 Operating Voltage Description Symbol Units Supply Voltage +5.0V Volts 6.6 Current Consumption Description Symbol Units Operating Current Consumption: I_Oper product functioning normally, but all LED’s off (Supply V = 5.0V) -
Page 11: Environmental Ratings And Reliability Test
Gyration, Inc. 7 Environmental Ratings and Reliability Test 7.1 Environmental Parameters PARAMETER UNITS Toper Operating Temp °C Tstore Storage Temp °C Hrel Relative Humidity (non- Percent condensing) @ 60°C Shock Survivability Alt_op Altitude, Operating 3,000 Alt_st Altitude, Storage 12,000 The unit should not be subjected to direct sunlight for extended periods of time. -
Page 12: Compliance
9.2 Production Testing Each unit is to be tested during the build process according to the applicable specification, approved by Gyration. Only units that conform to this document are shippable product. 9.3 Lot Sampling Testing Lot sampling testing must be performed at the manufacturer according to the applicable specification, approved by Gyration, prior to shipment. -
Page 13: Packaging Requirements
10 Packaging Requirements 10.1 Bulk Packaging Requirement Manufacturer must propose design of bulk packaging for product. Design of bulk packaging must be approved by Gyration, and must pass 10.2 - Bulk Packaging Qualification Testing. 10.2 Bulk Packaging Qualification Testing The design for Bulk Packaging Cartons should be qualified by the manufacturer by the following method: Each carton should be subjected to a six side/four corner drop test (1 meter) with no product damage. -
Page 14: Revision History
Gyration, Inc. 11 Revision History Date Description Initials 0/28/06 Initial draft 1.0A 09/14/06 Initial draft – Special for CCS Page 14 of 14...
Need help?
Do you have a question about the DE02559-001 and is the answer not in the manual?
Questions and answers