Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Lynxspring Manuals
  4. Monitor
  5. TSD7
  6. User manual

Lynxspring TSD7 User Manual

Touch screen display
Hide thumbs

Advertisement

Quick Links

Touch Screen Display
User Guide
200SM070 V1.3
Page 1 of 34

Advertisement

loading
Need help?

Need help?

Do you have a question about the TSD7 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Lynxspring TSD7

Summary of Contents for Lynxspring TSD7

  • Page 1 Touch Screen Display User Guide 200SM070 V1.3 Page 1 of 34...

  • Page 2: Table Of Contents

    Contents Powering Up the Device .......................... 4 Set the Locale ............................5 Connecting to a Source attached to a router over Wi-Fi – DHCP enabled ..........6 Connecting to a Source attached over Wi-Fi – Static IP Enabled............22 Connecting to a Source over Ethernet – DHCP enabled ............... 28 Connecting to a Source over Ethernet –...

  • Page 3: Powering Up The Device

    Powering Up the Device Once the installation of the display has been completed, a power source is connected, and the preferred communication method is known and available, power up the tablet by doing the following. • Press the power button once quickly and release. The battery indicator should appear. •...

  • Page 4: Set The Locale

    Set the Locale 1. Turn on the display. If for the first time, or there are no historical settings, you will see the screen display as below. Pick the desired language. Time can also be set now if incorrect. 2. Untick the box if you do not want to see this dialog box again. Locale configuration is also available in General Settings.

  • Page 5: Connecting To A Source Attached To A Router Over Wi-Fi - Dhcp Enabled

    Connecting to a Source attached to a router over Wi-Fi – DHCP enabled 1. If there are no historical settings, you will see this screen. Pick the desired connection type: 2. Select the network or source you wish to connect to from the list. Page 5 of 34 200SM070 V1.3...
  • Page 6 3. Enter the password for the network or source and click connect: 4. If WPS is available on your network or Source, select the top right tab & select ‘Advanced’ Page 6 of 34 200SM070 V1.3...
  • Page 7 5. Select the WPS push button feature and enable WPS on your source at the same time: 6.The WPS system should now connect. Once connected, click ‘Next’ Page 7 of 34 200SM070 V1.3...
  • Page 8 7. The application will search and find all the Sources on the network: 8. Once search and discovery is complete, the Networks and Content Sources configuration screen is shown: • NOTE: Select the button (top left) or swipe from the left edge of the screen to access the Menu.
  • Page 9 9. Various display settings can be configured by selecting General Settings: 10. General Settings • Change the language. • Change the Date / Time / Time Zone. • Adjust the dimming behaviour, To turn dimming off: o Set the dimming value to 0 or blank Page 9 of 34 200SM070 V1.3...
  • Page 10 Enabling content browsers. By default, this is off. The content will be displayed by the Kiosk browser, within Lynxspring APP. This gives a full browser experience in a full frame environment. If, however your content design is such that you need or prefer to use a typical internet browser, the options below are available.
  • Page 11 Selecting to enable this function, presents either of these options. • Once you have selected your browser & are happy with all the other settings, return to the Network Settings page. 11. Once the display has finished its discovery mechanism the Sources found are displayed, they will be listed showing the MAC address and the associated IP address.
  • Page 12 12. Click on the box to expand and view configuration options. c. The source can be renamed if required. d. Https can be enabled. e. A custom URL can be added. Include any custom port numbers in the URL, :8080, :8443 etc.
  • Page 13 Set the name Enable https Page 13 of 34 200SM070 V1.3...
  • Page 14 Set custom url including custom port number Collapse the box to save Page 14 of 34 200SM070 V1.3...
  • Page 15 13. Repeat steps 13 and 14 for each source you want to configure. 14. To reorder press and hold the drag and drop handle found on the right of each saved source, then drag up or down. The source at the top of the list is always displayed first. Page 15 of 34 200SM070 V1.3...
  • Page 16 15. To remove a Source, swipe left from the centre and click the remove button. This only removes this reference to the Source. It remains available in the device list. 16. Sources can also be added manually by using the ‘Add Source Manually’ button. Page 16 of 34 200SM070 V1.3...
  • Page 17 17. After clicking preview, web content from the top saved content source is displayed. A preview bar is display giving you easy access back to the Configuration screen. • If you have chosen more than one Source at launch point, then an additional ribbon will be superimposed at the bottom of the loaded screen, as above.
  • Page 18 18. When you are happy with the loaded content, click launch. Clicking ‘No’ will simply close the dialog. Clicking ‘Yes’ will put the display kiosk mode and a reboot will be required to make any further changes. 19. If you have selected to view content within a browser, such as Chrome, then the display will start the content within this browser.
  • Page 19 If you need at any point to change the network connection or change the launch sequence, re-boot the display by pressing the power button once only. When you see the Lynxspring splash screen below, tap the screen and the system will return to the network setup screen, where you can adjust to your requirements.
  • Page 20 The operation of the Display, as detailed to this point, are typical of all network connection methods. Please refer to the specific area of the document for your connection type and return to this section once connected. Page 20 of 34 200SM070 V1.3...

  • Page 21: Connecting To A Source Attached Over Wi-Fi - Static Ip Enabled

    Connecting to a Source attached over Wi-Fi – Static IP Enabled 1. Turn on the display 2. Select the network Page 21 of 34 200SM070 V1.3...
  • Page 22 3. Click Advanced options and scroll down 4. Select static Page 22 of 34 200SM070 V1.3...
  • Page 23 5. Give the display a Static IP to use on the network. Add other custom values if required, for example DNS 1. 6. Enter the password and click connect Page 23 of 34 200SM070 V1.3...
  • Page 24 7. Once connected to the network click next 8. The application will find all the Sources on the network Page 24 of 34 200SM070 V1.3...
  • Page 25 9. The Networks and Sources configuration screen is shown 10. After clicking preview, web content from the top saved content source is displayed. A preview bar is display giving you easy access back to the Configuration screen. Page 25 of 34 200SM070 V1.3...
  • Page 26 11. When you are happy with the loaded content, click launch. Clicking ‘No’ will simply close the dialog. Clicking ‘Yes’ will put the display kiosk mode and a reboot will be required to make any further changes. 12. After clicking launch, the Web App from the Source is displayed. Page 26 of 34 200SM070 V1.3...

  • Page 27: Connecting To A Source Over Ethernet - Dhcp Enabled

    Connecting to a Source over Ethernet – DHCP enabled 1. Boot the Source when connected via Ethernet. The connection type dialog is bypassed and the display finds all the Sources on the LAN. 2. Networks and Sources screen displaying all discovered Sources on LAN Page 27 of 34 200SM070 V1.3...
  • Page 28 3. Scroll to find the Source you want to connect to and click the blue arrow 4. Set the name and/or custom URL. This is where any ports are entered. In this case :3000 for the Niagara box we are connecting to Page 28 of 34 200SM070 V1.3...
  • Page 29 5. Once the source has been previewed and you click launch, the app will display whatever content the source serves. In this case the Niagara login screen. Page 29 of 34 200SM070 V1.3...

  • Page 30: Connecting To A Source Over Ethernet - Static Ip Enabled

    Connecting to a Source over Ethernet – Static IP Enabled 1. Boot the Source when connected via Ethernet. There is no DHCP so the connection type dialog is displayed 2. Select Ethernet from the list to administer the network settings Page 30 of 34 200SM070 V1.3...

  • Page 31: 200Sm070 V1.3

    3. Scroll to the bottom of the screen and select Ethernet IP mode. Select the desired option. 4. Enter network settings for static Ethernet connection. A value must be added to each field before the settings can be saved. Page 31 of 34 200SM070 V1.3...

  • Page 32: 200Sm070 V1.3

    5. Any Sources already connected to the same network will be found. 6. Scroll to find the Source you want to connect to and click the blue arrow Page 32 of 34 200SM070 V1.3...
  • Page 33 7. Set the name and/or custom URL. This is where any ports are entered. In this case :3000 for the Niagara box we are connecting to Page 33 of 34 200SM070 V1.3...
  • Page 34 8. Once the source has been previewed and you click launch, the app will display whatever content the source serves. In this case the Niagara login screen. Page 34 of 34 200SM070 V1.3...