Advertisement
4) Tool
For tightening the terminal, use a
With
commercially available small
straight tip
screwdriver having a straight form that is
not widened toward the end as shown
right.
0.4mm
2.5mm
Caution:
(0.02")
If the diameter of screwdriver grip is too
small, tightening torque will not be able
to be achieved. Use the following recommended screwdriver or an
appropriate replacement (grip diameter: approximately 25mm (0.98")).
Manufacturer
Model
Phoenix Contact Co., Ltd.
SZS 0.4×2.5
3.2 Wiring of Analog Output
→ For the terminal configuration, refer to Subsection 1.2.1
Using voltage
1DA-BD
Terminal
output
block
V+
I+
VI-
Grounding
Using current
1DA-BD
Terminal
output
block
V+
I+
VI-
Grounding
*1 Use 2-core shielded twisted pair cable for the analog output lines, and
separate the analog output lines from other power lines or inductive lines.
*2 The grounding resistance should be 100Ω or less.
3.3 Grounding
Grounding should be performed as stated below.
• The grounding resistance should be 100Ω or less.
• Independent grounding should be performed for best results.
When independent grounding is not performed, perform "shared
grounding" of the following figure.
→ For details, refer to the FX
Series User's
3G
Manual - Hardware Edition.
Other
Other
PLC
PLC
PLC
equipment
equipment
Independent grounding
Shared grounding
Common grounding
Best condition
Good condition
Not allowed
• The grounding wire size should be AWG 22-20 (0.3-0.5 mm
• The grounding point should be close to the PLC, and all grounding wire
should be as short as possible.
4. Specifications
STARTUP AND
MAINTENANCE
PRECAUTIONS
• Do not disassemble or modify the PLC.
(0.1")
Doing so may cause fire, equipment failures, or malfunctions.
* For repair, contact your local Mitsubishi Electric distributor.
• Do not drop the product or exert strong impact to it.
Doing so may cause damage.
DISPOSAL
PRECAUTIONS
• Please contact a certified electronic waste disposal company for the
environmentally safe recycling and disposal of your device.
TRANSPORT AND
STORAGE PRECAUTIONS
• The product is a precision instrument. During transportation, avoid any impacts.
Failure to do so may cause failures in the product. After transportation, verify the
operations of the product.
4.1 Applicable PLC
Model name
Applicability
FX
3G
Series PLC
Ver. 1.10 or later
The version number can be checked by monitoring D8001 as the last three digits
indicate it.
• The number of connectable expansion boards varies depending on the main unit as
follows:
FX
-14M , 24M
Main units : 1 unit
3G
FX
-40M , 60M
Main units : 2 units
3G
Never stack up two or more expansion boards.
For details on the system configuration, refer to the following manual.
→ Refer to the FX
/FX
/FX
Series User's Manual - Analog Control Edition
3G
3U
3UC
4.2 General Specifications
The general specifications are equivalent to the PLC main unit.
For general specifications, refer to the following manuals.
→ Refer to the FX
3G
Series User's Manual - Hardware Edition
4.3 Performance Specifications
Specifications
Item
Voltage output
0 to 10V DC
Analog output
(External load resistance:
range
2kΩ to 1MΩ)
Other
equipment
Digital input
12 bits, binary
Resolution
2.5mV(10V/4000)
• ±0.5%(±50mV) for full scale
of 10V(when ambient
2
temperature is 25°C±5°C)
).
• ±1.0% (±100mV) for full
scale of 10V
(when ambient temperature
is 0°C to 55°C)
Shipment adjustment is carried
out by external load resistance
2kΩ.
I f e x t er n al l o a d r es i s tan c e
becomes larger than 2kΩ, the
Total accuracy
output voltage will increase
slightly.
When the load is 1MΩ, the
output voltage becomes about
2% higher than the correct
value.
Caution:
An area of dead band is located
in the region of 0V.
Therefore the output analog
value may not represent the
digital value accurately.
D/A
60μs
conversion
(The data will be updated at every scan time of the PLC.)
time
Item
Voltage output
0 to 4000 are adjusted to 0 to
10V when the external load
resistance is 2kΩ.
output
10V
characteristics
0
Digital input
Insulation
No insulation between the PLC.
method
Occupied
0 point (This number is not related to the maximum number of
points
input/output points of the PLC.)
4.4 List of Special Devices
Device number
BD1
BD2
M8260
M8270
Special
auxiliary
relay
M8264
M8274
D8260
D8270
Special
data
D8268
D8278
register
D8269
D8279
Current output
4 to 20mA DC
As for the details of the special devices, refer to the following manual.
→ Refer to the FX
(External load resistance:
FX
FX
3G/
3U/
500Ω or less)
11 bits, binary
8μA(16mA/2000)
• ±0.5%(±80μA) for full scale
of 16mA(when ambient
temperature is 25°C±5°C)
• ±1.0%(±160μA) for full
scale of 16mA
(when ambient temperature
is 0°C to 55°C)
Specifications
Current output
0 to 2000 are adjusted to 4 to
20mA when the external load
resistance is 250Ω.
20mA
4mA
4000
4080
0
2000
2040
Digital input
R: Read W: Write
Description
R/W
Switches the output mode
R/W
OFF: Voltage output ON: Current output
Output Holding Function Cancellation
Setting
OFF: Holds the analog data output just
R/W
before stop of the PLC.
ON: Output the offset data at stop of the
PLC.
Output setting data
R/W
Error status
b0: Output data setting error
b1: Unused
b2: Unused
R/W
b3: Unused
b4: EEPROM error
b15 to b5: Unused
Model code = 4
R
Series User's Manual - Analog Control Edition
3UC
This manual confers no industrial property rights or any rights of any other kind,
nor does it confer any patent licenses. Mitsubishi Electric Corporation cannot be
held responsible for any problems involving industrial property rights which may
occur as a result of using the contents noted in this manual.
Warranty
Mitsubishi will not be held liable for damage caused by factors found not to be
the cause of Mitsubishi; opportunity loss or lost profits caused by faults in the
Mitsubishi products; damage, secondary damage, accident compensation
caused by special factors unpredictable by Mitsubishi; damages to products
other than Mitsubishi products; and to other duties.
This product has been manufactured as a general-purpose part for general
industries, and has not been designed or manufactured to be incorporated in
a device or system used in purposes related to human life.
Before using the product for special purposes such as nuclear power, electric
power, aerospace, medicine or passenger movement vehicles, consult with
Mitsubishi Electric.
This product has been manufactured under strict quality control. However
when installing the product where major accidents or losses could occur if the
product fails, install appropriate backup or failsafe functions in the system.
HEAD OFFICE
HIMEJI WORKS
For safe use
: TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310,
JAPAN
: 840, CHIYODA CHO, HIMEJI, JAPAN
Advertisement
