FC LIGHTING FCSL101-FCSL106 Installation Instructions

INSTALLATION INSTRUCTIONS
FCSL100 SERIES -
CAUTION: BEFORE CONNECTING THE FIXTURE TO A POWER SUPPLY, MAKE SURE THE POWER IS SWITCHED OFF.
NOTE: Faceplates - The Faceplate type used determines fixture installation.
FCSL101-FCSL106 mounts flush to front of Fixture Lip. (Fig. 1) and
FCSL108-FCSL110 fits over (wraps around) Fixture Lip. (Fig. 2) and
GENERAL:
1. Before starting the installation, make sure all electricity has been turned off and electrical
breaker has been locked out and tagged out.
2. To ensure the success of the installation, be sure to read these instructions and review the
diagrams thoroughly before beginning.
3. All electrical connections must be in accordance with local codes, ordinances, or the
National Electrical Code.
NOTE: The important safeguards and instructions appearing in this manual are not meant to
cover all possible conditions and situations that may occur.
INSTALLATION INSTRUCTIONS:
A) Remove the two (2) socket head screws holding Lens and Faceplate to fixture. Then remove
internal lamping components (guts) from fixture.
FOR CONCRETE POUR: Be sure to level and stabilize fixture. Cover any holes and knockouts on
fixture housing to prevent leakage. Seal the fixture to prevent water leakage during operation.
FOR DRYWALL MOUNT: Cut hole in drywall (2-5/8" x 9-3/8") for flush mount
(2-5/16" x 8-5/16") for front mount . Refer to detailed instructions on page 2.
C
NOTE: PL version is not for through wiring. All connections must be water tight.
1) Connect conduit or code approved electrical fitting through one of the 7/8" diameter holes
on the back or side of the fixture. Secure fixture housing to forms outside of gasket area.
Refer to Fig. 3 on pg. 2 using Hanger Brackets and Drywall Adapters for Front Mounted
drywall application.
2) After fixture is mounted, connect your ground wire to green ground wire on fixture.
3) Replace internal components with approved lamp.
4) Attach lens and frame, replace two (2) socket screws tightening evenly.
5) Restore power and test fixture. If fixture does not turn on, disconnect power before
checking for problems.
IMPORTANT: Fixtures are listed for installation with liquid tight or rigid wall conduit only.
Fixtures installed without a silicone bead will void the warranty.
D
3 in.
22.23 TYP 2
BOSS REQUIRED FOR GROUND SCREW.
8MM OD X 8MM TALL BLIND TAP 6-32, 8MM DEEP
THIS DOCUMENT IS PROPRIETARY TO FC LIGHTING, INC. ANY UNAUTHORIZED TRANSFER, USE OR REPRODUCTION IS STRICTLY PROHIBITED.
page 1 of 2
(HB)
B
(DWR)
C
or
B
9.375 in .125 in
2.8 in
2 x 1MM DEEP
TYP 2
3 X 6MM DEEP 8-32 THREADED
BLIND HOLE TYP 4 INSERT TYP2
DETAILED ILLUSTRATION
1/2" trade connector openings
Back of Fixture
Fixture Housing
Back of Fixture
A
B
Mounting for Fig. 1 Faceplate type.
Same for concrete or drywall application.
Front of Fixture Lip Mounted Flush with Wall.
Apply Silicone Bead
Use HB for proper installation.
D
C
Mounting for Fig. 2 Faceplate type.
Same for concrete or drywall application.
Apply Silicone Bead Fixture Lip Mounted in Front of Wall.
Use DWR for proper installation
D
t 800.900.1730 f 630.889.8106
3609 Swenson Ave. St. Charles, IL 60174
Fixture Lip
Fig. 1
Faceplate mounts to
Front of Fixture Lip.
Use mounting
Fig. 2
Faceplate fits
Fixture Lip
over Fixture Lip.
Use mounting
Fixture Lip
Gasket Area
Adapter Screw
Drywall Adapter
Fig. 3
Drywall Adapter
(DWR)
Fixture Lip in Wall
Tighten
Screw
Adapter holds
Fixture in place.
Fixture Lip against Wall
©2016 FC LIGHTING, INC.
B
C
JO Rev. 0218