Advertisement
5.3.2.
After adjusting the fence always ensure that it is parallel to the blade by measuring the position of each end from the "0" graduations on
the table. tighten the clamp screws.
6. cHaNGiNG THe blaDe
6.1.
remove the water tray from under the cutter and ensure that the work table
is not at an angle.
6.2.
tilt the cutter onto the left-hand side and remove the lower blade guard.
6.3.
Hold the end of the shaft (fig. 2.d) with a spanner on the flats and remove
the blade retaining nut (fig. 2.A).
6.4.
remove the outer blade washer (fig. 2.B) and the blade.
6.5.
When fitting the new blade it is very important to ensure that the rotation
arrows on the blade match the direction arrow on the blade guard.
6.6.
tighten retaining nut while holding shaft end with spanner.
Note: the two blade washers (fig.2.B & c) are different and must be
correctly fitted. the inner washer (c) has a spigot (c1), to locate the
blade, which is not present on the outer washer. each washer must
be fitted with the flat face in contact with the blade.
6.7.
replace lower blade guard, stand cutter upright and refit water tray.
7. OperaTiNG iNSTrucTiONS
WArninG! As with all power tools, there are potential hazards involved with the use of this cutter. it is, therefore, vital to ensure you read,
‰
understand and apply all the safety instructions in section 1. familiarise yourself again with the specific safety rules for each step of the
following operation. failure to do so may cause serious damage and/or personal injury and may invalidate your warranty. disconnect
the cutter from the mains power before making adjustments or changing blades. ensure that all clamps, screws and nuts are secure
and that the blade is in good condition and correctly mounted. AlWAYs have the blade guard down before turning on the cutter. Wear
approved safety eye protection.
7.1.
fill the water tray approx. two thirds so that the lower blade guard is in the water. the water cools and lubricates the blade during
cutting and also helps to suppress the dust.
7.2.
set the table tilt angle and the fence position to suit the required cut. lower the blade guard as far as possible whilst leaving room for
the tile to pass beneath it.
7.3.
check that everything is ready, plug the cutter into the mains power supply and switch on.
WarNiNG! DO NOT attempt to pick up an off-cut before the blade has completely stopped.
‰
7.4.
Hold work firmly against the fence and table (hold the main section, not the piece that will become the off-cut).
7.5.
slowly move the work piece forward into the rotating blade. continue holding the work piece firmly until the cut is complete.
parts support is available for this product. To obtain a parts listing and/or diagram,
please log on to www.sealey.co.uk, email sales@sealey.co.uk or telephone 01284 757500.
environmental protection
recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be
sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment.
When the product becomes completely unserviceable and requires disposal, drain off any fluids (if applicable)
into approved containers and dispose of the product and the fluids according to local regulations.
Weee regulations
dispose of this product at the end of its working life in compliance with the eu directive on
Waste electrical and electronic equipment (Weee). When the product is no longer required, it must be disposed
of in an environmentally protective way. contact your local solid waste authority for recycling information.
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
iMpOrTaNT: no liability is accepted for incorrect use of this product.
WarraNTy: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
© Jack sealey limited
sole uK distributor, sealey Group.
Kempson Way, suffolk Business Park,
Bury st. edmunds, suffolk.
iP32 7Ar
Original Language Version
fig.2
01284 757500
01284 703534
tc180.V2 | issue 3 05/12/16
www.sealey.co.uk
sales@sealey.co.uk
Advertisement
