HIKVISION UD04872B User Manual

COPYRIGHT ©2017 Hangzhou Hikvision Digital Technology Co., Ltd. ALL RIGHTS RESERVED. Regulatory Information
About this Manual FCC Information
The Manual includes instructions for using and managing the product. Pictures, charts, images and Please take attention that changes or modification not expressly approved by the party responsible
all other information hereinafter are for description and explanation only. The information for compliance could void the user's authority to operate the equipment.
contained in the Manual is subject to change, without notice, due to firmware updates or other FCC compliance: This equipment has been tested and found to comply with the limits for a Class B
reasons. Please find the latest version in the company website (http://overseas.hikvision.com/en/). digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
Visit the company website (http://overseas.hikvision.com/en/) to get the manuals, client software, protection against harmful interference in a residential installation. This equipment generates, uses
and developing tools. and can radiate radio frequency energy and, if not installed and used in accordance with the
Please use this user manual under the guidance of professionals. instructions, may cause harmful interference to radio communications. However, there is no
Trademarks Acknowledgement guarantee that interference will not occur in a particular installation. If this equipment does cause
and other Hikvision's trademarks and logos are the properties of Hikvision in various harmful interference to radio or television reception, which can be determined by turning the
jurisdictions. Other trademarks and logos mentioned below are the properties of their respective equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
owners.
—Reorient or relocate the receiving antenna.
Legal Disclaimer
—Increase the separation between the equipment and receiver.
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED "AS IS", WITH ALL FAULTS AND ERRORS, AND
connected.
HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION,
MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND —Consult the dealer or an experienced radio/TV technician for help.
NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL HIKVISION, ITS DIRECTORS, OFFICERS, This equipment should be installed and operated with a minimum distance 20cm between the
EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR radiator and your body.
INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, FCC Conditions
BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH THE USE This device complies with part 15 of the FCC Rules. Operation is subject to the following two
OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Wi-Fi Video Doorbell conditions:
REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY AT
1. This device may not cause harmful interference.
YOUR OWN RISKS. HIKVISION SHALL NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL OPERATION,
2. This device must accept any interference received, including interference that may cause
User Manual
PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER ATTACK, VIRUS
undesired operation.
INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE TIMELY
EU Conformity Statement
TECHNICAL SUPPORT IF REQUIRED.
This product and - if applicable - the supplied accessories too are marked with "CE" and
SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR
comply therefore with the applicable harmonized European standards listed under the
JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS THE
EMC Directive 2014/30/EU, the RoHS Directive 2011/65/EU.
APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH
2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as
ILLEGITIMATE PURPOSES.
unsorted municipal waste in the European Union. For proper recycling, return this product
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER
UD04872B
to your local supplier upon the purchase of equivalent new equipment, or dispose of it at
PREVAILS.
designated collection points. For more information see: www.recyclethis.info
1
2006/66/EC (battery directive): This product contains a battery that cannot be disposed of Symbol Conventions
as unsorted municipal waste in the European Union. See the product documentation for The symbols that may be found in this document are defined as follows.
specific battery information. The battery is marked with this symbol, which may include
lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return
the battery to your supplier or to a designated collection point. For more information see:
www.recyclethis.info
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to
the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired
● The working temperature of the device is from -30° C to 50° C .
operation of the device.
● All the electronic operation should be strictly compliance with the electrical safety regulations, fire
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radioexempts
prevention regulations and other related regulations in your local region.
de licence. L'exploitation est autorisée aux deux conditions suivantes :
● Please use the power adapter, which is provided by normal company. The power consumption
(1) l'appareil ne doit pas produire de brouillage, et
cannot be less than the required value.
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage
● Do not connect several devices to one power adapter as adapter overload may cause over-heat or
est susceptible d'en compromettre le fonctionnement.
fire hazard.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a
● Please make sure that the power has been disconnected before you wire, install or dismantle the
type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce
device.
potential radio interference to other users, the antenna type and its gain should be so chosen that
● When the product is installed on wall, the device shall be firmly fixed.
the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful
● If smoke, odors or noise rise from the device, turn off the power at once and unplug the power
communication.
cable, and then please contact the service center.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut
● If the product does not work properly, please contact your dealer or the nearest service center.
fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour
Never attempt to disassemble the device yourself. (We shall not assume any responsibility for
l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à
problems caused by unauthorized repair or maintenance.)
l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la
puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établisse-
ment d'une communication satisfaisante. ● Do not drop the device or subject it to physical shock, and do not expose it to high electromag-
netism radiation. Avoid the equipment installation on vibrations surface or places subject to shock
This equipment should be installed and operated with a minimum distance 20cm between the
(ignorance can cause equipment damage).
radiator and your body.
● Do not place the device in extremely hot (refer to the specification of the device for the detailed
Cet équipement doit être installé et utilisé à une distance minimale de 20 cm entre le radiateur et
votre corps. operating temperature), cold, dusty or damp locations, and do not expose it to high electromagnetic
radiation.
2 3
● The device cover hall be kept from rain and moisture.
● Exposing the equipment to direct sun light, low ventilation or heat source such as heater or
Provides additional information to emphasize or supplement important radiator is forbidden (ignorance can cause fire danger).
points of the main text. ● Do not aim the device at the sun or extra bright places. A blooming or smear may occur otherwise
(which is not a malfunction however), and affecting the endurance of sensor at the same time.
Indicates a potentially hazardous situation, which if not avoided, could result
● Please use the provided glove when open up the device cover, avoid direct contact with the device
in equipment damage, data loss, performance degradation, or unexpected
cover, because the acidic sweat of the fingers may erode the surface coating of the device cover.
results.
● Please use a soft and dry cloth when clean inside and outside surfaces of the device cover, do not
Indicates a hazard with a high level of risk, which if not avoided, will result in
use alkaline detergents.
death or serious injury.
● Please keep all wrappers after unpack them for future use. In case of any failure occurred, you
need to return the device to the factory with the original wrapper. Transportation without the
original wrapper may result in damage on the device and lead to additional costs.
● Please connect a resistor (included in the box content) to the doorbell if no electrical chime or
mechanical chime is connected.
(16 VAC to 24 VAC)
Resistor
Wi-Fi Video Doorbell
Make sure the power voltage across the doorbell should be between 16 VAC and 24 VAC.
● The power supply must conform to LPS. The recommended adaptor models and manufacturers are
shown as below. Use the attached adapter, and do not change the adaptor randomly.
Model Manufacturer
MKAC-57-242500M MACABLE
MKAC-57-242200M MACABLE
MACABLE
MKAC-57-241500M
4 5
Appearance
Mic
IR Light
Lens
Screw 1
Button Backlight
Screw 2 TF Card Slot
Loudspeaker
Backlit Call Button
Name Description Name Description
TF Card Slot For TF card. If a TF card is used, video files will be stored in the TF
IR Light Auto light source for night vision. The lights are behind the panel.
card.
. Solid blue: The doorbell is starting up and running properly.
. If the doorbell has not been activated, hold the button for
RESET Button
. Cycling blue and red: Wi-Fi is not connected.
5 seconds to enter the Wi-Fi connection mode. The call
Button .
Flashing red: The doorbell is upgrading.
Backlight backlight cycles blue and red.
.
Flashing blue: The doorbell is calling the App.
. If you do no operation in 3 minutes the doorbell
No backlight: The doorbell is speaking with the App.
will exit the Wi-Fi configuration automatically.
Screw 1&2 These 2 screws are used to connect the power cables. . If the doorbell has been activated, hold the button for 15
seconds to restore the factory settings.
7
6
Installation
Step 1 (Optional) Install the TF card.
Remove the card slot cover, and insert the TF card into the card slot on the side of
the doorbell .
TF Card
Mini USB Slot
RESET Button
Motion detection does not support recording without the TF card.
Step 2 Attach the mounting template.
- Align the cable hole on the mounting template with the cable hole on the
wall.
- Attach the mounting template on the wall.
42 mm
. Mounting Template
Paste the template on the
required place.Drill screw
. according to the template. holes and cable holes
Hole A:Cable Hole.
Hole 1:Wall Mounting Screw
Hole.
8