Subscribe to Our Youtube Channel
Summary of Contents for Avenview KPD-TCP1US-8
- Page 1 VIDEO WALLS VIDEO PROCESSORS VIDEO MATRIX SWITCHES EXTENDERS SPLITTERS WIRELESS CABLES & ACCESSORIES Control Your Video PRODUCT MANUAL Model: KPD-TCP1US-8 8-Button Wall Plate Control Keypad...
- Page 2 No license, whether express, implied, or otherwise, to any intellectual property rights is granted by this publication. Except as set forth in Avenview Standard Terms and Conditions of Sale, Avenview assumes no liability whatsoever, and disclaims any express or implied warranty, relating to its products of Avenview Inc.
-
Page 3: Table Of Contents
PANEL DESCRIPTION..............................6 2.4.1 I/O PANEL (KPD-TCP1US-8) FRONT......................6 2.4.2 I/O PANEL (KPD-TCP1US-8) BACK......................6 INSTALLATION................................7 TELNET CONFIGURATION............................7 3.1.2 ENABLING TELNET CLIENT........................8 LOGIN TO KPD-TCP1US-8 VIA TELNET........................9 TELNET COMMANDS...............................10 PC SOFTWARE................................11 WEBGUI..................................12 CONFIGURATION SETTINGS..........................12 MACRO SETTINGS..............................13 4.2.1 MACRO EDIT MENU...........................13 4.2.2 COMMAND SELECT MENU........................14 EXTENSION MACRO..............................15... -
Page 4: Getting Started
• Removal, installation, and set-up service charges. SAFETY GUIDELINES The KPD-TCP1US-8, 8-Button Wall Plate Control Keypad has been tested for conformance to safety regulations and requirements, and has been certified for international use. However, like all electronic equipments, the HBT2-C6BPOC-SET should be used with care. -
Page 5: Regulatory Notices Federal Communications Commission (Fcc)
Properly shielded and grounded cables and connectors must be used in order to meet FCC emission limits. Avenview is not responsible for any radio or television interference caused by using other than recommended cables and connectors or by unauthorized changes or modifications to this equipment. -
Page 6: Intruduction
INTRODUCTION The Avenview KPD-TCP1US-8, 8-Button Wall Plate Control Keypad is a versatile and useful control method for both system integrators and smart home users alike. This keypad can send commands to any Ethernet or relay trigger controlled device in your system. With up to 8 physical macro buttons and up to an additional 8 software macro buttons you can pre-program and recall up to 16 distinct macros providing for complete control over your audio and video environment. -
Page 7: Package Contents
PACKAGE CONTENTS Before you start the installation of the KPD-TCP1US-8, please ensure that the packaging has the listed items below. ITEM KPD-TCP1US-8 8-Button Wall Plate USB Type A to Mini USB OTG Connector 3.5mm Pitch Terminal Block 5 V/2.6A Power Adaptor... -
Page 8: Application Diagram
APPLICATION DIAGRAM www.avenview.com Rev.00 12/2017... -
Page 9: Panel Description
PANEL DESCRIPTION 2.4.1 I/O PANEL (KPD-TCP1US-8) Front 1-8 Macro Buttons: Each button has a red and blue LED dimmable from 0~100% and can be configured with up to 16 commands. Refer to Section 4 for more details. 2.4.2 I/O PANEL (KPD-TCP1US-8) Rear... -
Page 10: Installation
3.1.1 Setting a Static IP on Your Computer Before logging in to the keypad via TELNET command-line interface (CLI) or Web GUI, make sure that your computer/controller and KPD-TCP1US-8 are on the same network segment. The default network settings of the unit is 192.168.1.50, subnet mask 255.255.225.0. -
Page 11: Enabling Telnet Client
Windows 7. Follow these instruction to enable the Telnet Client. 1. Choose Start > Control Panel > Programs. 2. In Programs and Features, click Turn Windows features on or off. 3. In Windows Features dialog box, select Telnet Client check box. www.avenview.com... -
Page 12: Login To Kpd-Tcp1Us-8 Via Telnet
In the Run dialog box, enter ‘cmd’ then click OK Enter ‘telnet 192.168.1.50 23’ then press Enter The Welcome Dialog will appear as below. Enter API commands from this document to control and configure your KPD-TCP1US-8 keypad. Enter ‘?’ to quickly list available commands. www.avenview.com... -
Page 13: Telnet Commands
KEY_PRESS # HOLD Configures the selected button to activate its # (Button) = 1..8 command when pressed and held MACRO RUN # # (Macro) = 1..16 Activate the selected macro MACRO STOP NONE Stops all active macros www.avenview.com Rev.00 12/2017... -
Page 14: Pc Software
3.4. PC SOFTWARE APPLICATION If you have lost the network configuration for the KPD-TCP1US-8 or you are unable to access the WebGUI, the Discovery PC software application can be used to recover the network settings of any connected keypad. The software can downloaded here. Download the software and extract the files http://avenview.com/downloads/DiscoveryTool.zip... -
Page 15: Webgui
WEBGUI All of the options and settings of the Avenview KPD-TCP1YS-8, 8-Button Wall Plate Control Keypad can be configured through the WebGUI interface. To access the WebGUI, ensure your PC and the keypad are on the same network segment (See section 3.1.1 for more details) then open a web browser. -
Page 16: Macro Settings
Click the ‘Save Changes’ button to save the macro and close the window. To add a command to the macro, click the ‘Add’ button. This will open the ‘Command Select’ menu. www.avenview.com Rev.00 12/2017... -
Page 17: Command Select Menu
Note: It is strongly suggested to not set a delay time less than 100ms for system commands or less than 500ms for Telnet commands to ensure that the command is properly received and executed before the next command is sent. www.avenview.com Rev.00 12/2017... -
Page 18: Extension Macro
Return and Line Feed respectively. See section 3.3 for the proper format of System Commands. As you can see below, the command used to change an LED follows the format of the Telnet commands. (Including Carriage Return and Line Feed characters) www.avenview.com Rev.00 12/2017... -
Page 19: Device Settings
In “Toggle” mode, you can configure a buton to switch between the assigned macro of that button and the assigned macro of a software button. In the screenshot below, button 5 is configured to toggle between the commands assigned to that key and the commands assigned to software key 13. www.avenview.com Rev.00 12/2017... -
Page 20: Schedule
From the ‘Macro Select’ menu, you can choose the desired macro to activate at the specified date and time. Click ‘Save Change” to save the scheduled macro. Note: The KPD-TCP1US-8 supports up to 48hrs of battery backup for the real-time clock. After 48hrs the system will reset the time to 2015/01/01 00:00:00. -
Page 21: Netowrk Settings
Options to reboot and factory reset the unit are also available in this menu. 4.10 TIME SETTINGS System time and Daylight Savings Time settings can be changed from this menu. If power is removed from the keypad for more than 48hrs, the system time will need to be reset. www.avenview.com Rev.00 12/2017... -
Page 22: Specifications
SPECIFICATIONS ITEM DESCRIPTION UNIT KPD-TCP1US-8 UNIT DESCRIPTION 8-Button Wall Plate Control Keypad INPUT PORTS 8 x Buttons, DC Power OUTPUT PORTS 1 x Relay (Terminal Block), 1 x RJ-45 Ethernet Port POWER SUPPLY 5V@2.6A DC (US/EU standards, CE/FCC/UL Certified) POWER CONSUMPTION 3.3W... -
Page 23: Warranty
Rev.00 12/2017... -
Page 24: Technical Support
Disclaimer While every precaution has been taken in the preparation of this document, Avenview Inc. assumes no liability with respect to the operation or use of Avenview hardware, software or other products and documentation described herein, for any act or omission of Avenview concerning such products or this documentation, for any interruption of service, loss or interruption of business, loss of anticipatory profits, or for punitive, incidental or consequential damages in connection with the furnishing, performance, or use of the Avenview hardware, software, or other products and documentation provided herein.
Need help?
Do you have a question about the KPD-TCP1US-8 and is the answer not in the manual?
Questions and answers