Download Print this page

Cabletime MediaStar 514 Quick Start Manual

Wired remote control

Advertisement

Quick Links

Page 4
RegulatoRy RequiRement notices
EuropE
Cabletime Limited declare that the products described in this manual conform to the requirements
of the following Directives:
89/336/EEC
92/31/EEC
Low Voltage Directive 73/23/EEC
ThE sTanDarDs appLiED arE:
BSEN55022:1998
Limits and methods of measurement of radio interference characteristics of
information technology equipment
Bsen50082-1:1998 electromagnetic compatibility - generic immunity standard
Bsen60950-1:2000 specification for safety of information technology equipment, including electrical
business equipment
Bsen60065:2002
audio Video and similar electronic apparatus safety requirements
uniTED sTaTEs of amEriCa
Cabletime Limited declare this equipment has been tested and found to comply with the limits for a Class a
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
This device complies with part 15 of the FCC Rules.
operation is subject to the following conditions:
This device may not cause harmful interference, and
This device must accept any interference received, including interference that
may cause undesired operation.
Whilst all reasonable care has been taken to ensure the accuracy of this publication, the publishers and authors cannot
accept responsibility for any errors and omissions. Cabletime Limited reserves the right to revise this publication and to
make changes in the content from time to time without notice.
Copyright © Cabletime 2007. All rights reserved. No part of this guide may be reproduced, stored in a retrieval system or
transmitted in any form or by any means (electronic, mechanical, photocopying, recording or otherwise) without prior written
permission of Cabletime Ltd.
Cabletime Limited, 64 Greenham Road, Newbury, Berkshire, RG14 7HX England
Email: support@cabletime.com
Quick Start Guide
Getting Started With MediaStar
The MediaStar 514 Wired Remote Control can be used with all MediaStar
systems where a wired push button controller is required, rather than the
standard infra-red remote control and IR receiver. This unit connects to either
the MediaStar Evolution 760 and 760/xM units, MediaStar Pro 507 Micro
Settops, or MediaStar Compact 751 receivers (all referred to as 'endpoints' in
this document).
WHAT'S IN THE BOX
3.5mm jack
red LED
imPoRtant
This unit has to be PROGRAMMED to operate correctly with each
type of MediaStar endpoint equipment. Programming instructions are
shown below. If this unit is plugged in but key presses do not get any
response from the system, it is likely the Wired remote Control has
been programmed to work with the wrong type of mediastar endpoint
equipment.
514 Wired Remote Control
• 514 Wired Remote Control
• 514 Quick Reference Card

Advertisement

loading

Summary of Contents for Cabletime MediaStar 514

  • Page 1 Video and similar electronic apparatus safety requirements red LED uniTED sTaTEs of amEriCa Cabletime Limited declare this equipment has been tested and found to comply with the limits for a Class a digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in...
  • Page 2: Important Safety Instructions

    Page 2 Page 3 installation imPoRtant safety instRuctions start by removing the existing ir receiver module from the endpoint by 1. Read these instructions. unplugging its 3.5mm jack plug. For MediaStar Compact 751 units, the built 2. Keep these instructions. in ir receiver may be currently used, so there may be no external ir receiver jack plug to remove. 3. Heed all warnings. Insert the 3.5mm jack plug of the Wired Remote Control into the endpoint’s 4. Follow all instructions.