Team Corally C-53008 Instruction Manual

TC SMART BOX
INSTRUCTION MANUAL
Introduction Features
• ESC Settings
Setting up all parameters of your ESC made easy with this digital
• Servo Tester
programmer. The bright LCD screen let you run through all the
programs and within seconds the values have been changed. This • PC Interface - Link ESC to PC
programmer can also be used as interface between your PC and • Motor KV/RPM Tester
• Input PPM Signal Monitor
the ESC to update your fi rmware or to do even more set-ups.
• LiPo Battery Analyzer
The TC Smart Box offers six-in-one functions:
Connectivity Technical Specifi cations
Suitable for
Cerix Pro 120
Cerix Pro 120 1S
Motor Sensor
Cerix PRO 160
Connector
Revoc Pro 160
LCD Screen
Battery Balance
2 Lines - 16 Characters Input Voltage
6 - 10V DC
Connector
Input Current
Idle Current
Dimensions 85x55x13mm
Weight
USB to PC
I/O Connector
ENTER key
INC+ key (Up)
DEC- key (Down)
EXIT key (Esc)
Functions
ESC Setting
The TC Smartbox can work as an individual device to program the ESC. The options of each parameter are
displayed on the LCD screen.
Servo Tester
The TC Smartbox can check the input voltage, servo travel position and peak current of your servo.
PC Interface
The TC Smartbox can work as an USB adaptor to link the ESC with your PC.
The user can update the fi rmware of the ESC or program the ESC by the TC CONNECT software on PC.
Motor KV/RPM Tester
The TC Smartbox can check the motor KV, RPM and input voltage.
Input PPM Signal Monitor
The TC Smartbox can check the output voltage from the receiver and the receiver's PPM signal/pulse width
and frequency.
LiPo Battery Analyzer
The TC Smartbox can be used as a batterypack analyzer and tester to check the total cell number, total volt-
age, each cell voltage, highest voltage and lowest voltage and the voltage difference between the highest
voltage and lowest voltage.
Page 1
Safety Notes
• This Smartbox is not a toy and only suitable for users from age 14+
• Never allow water, moisture, oil or other materials to get in contact or inside the Smartbox. It may damage
the Smartbox completely.
• Never disassamble the Smartbox or modify the components on the PC board
• We strongly suggest to use the original wires and connectors supplied in the ESC packaging
• To avoid short circuit, please keep the connectors away from any metal parts.
• Never connect a battery with reversed polarity.
Team Corally can never be held responsible for any damage caused or related to the
non-compliance with the above instructions.
Application
There are 4 program buttons on the TC Smartbox
ENTER Press this button to ENTER into the referred menu or to CONFIRM your selection
...
DEC- Press this button to PAGE DOWN or SCROLL DOWN in the menu / selection
500mA
INC+ Press this button to PAGE UP or SCROLL UP in the menu / selection
< 20mA
Press this button to EXIT and go back to previous menu
EXIT
46g
ESC Settings
Connect the Smartbox as
shown, turn on the ESC and
follow these steps.
Press ENTER button to enter
different programmable items,
press or buttons
DEC- INC+
to browse all the options and
press button to confi rm
ENTER
your selection and then the
screen will go back to the main
program menu
ENTER
When the screen displays the programed item, you can press the
EXIT
program menu and start to program next item.
Note: The programmable items in the menu may be differ between the different type of ESC's
Page 2
Li-Po Battery Analyzer
The Smartbox can check the total cell number, total voltage, each cell voltage, highest voltage and lowest
voltage and the voltage difference between the highest voltage and lowest voltage.
Connect the Smartbox and the battery as shown, monitor battery voltage as follows
Input PPM Signal Monitor
The Smartbox can check the output voltage from the receiver, the receiver's PPM signal / pulse width and
frequency.
Connect RX Power
4.8 - 7.4V
or
ESC with battery
connected
Connect the Smartbox with the receiver as shown, and
turn on the ESC and the transmitter. Please note that the
ENTER Smartbox must be inserted in the Throttle Channel and
a RX powerpack or the ESC can be inserted to any free
channel of the receiver to supply power to the receiver.
ENTER
When all is connected, the Smartbox will display the output
voltage from the receiver, the receiver's frequency and the
button to go back to the main
neutral pulse position.
Hold full throttle and hold full brake to check the receiver's
PPM signal / pulse width.
Servo Tester
The Smartbox can check the input voltage, servo travel position and peak current of your servo.
The default servo neutral position is 1520us/100Hz and 760us/100Hz. If the testing servo is not
1520us/100Hz and 760us/100Hz, please enter CUSTOM and set the servo neutral position (range: 200-
2000us) and frequency(range: 50-200Hz) by yourself.
There are two kinds of mode "Swing Mode" and "Manual Mode" to make the servo swing and check
the servo travel position.
Swing Mode: The Smartbox will send out a signal to make the servo swing automatically
Manual Mode: The Smartbox allows you to change the PPM signal and check the servo's response to the
signal.
DEC-
DEC-
*Remark 1 When you enter this screen, press
position of the servo and enter to frequency setting.
Press
*Remark 2 In this screen, press
ENTER
In this screen, press
*Remark 3
check the response of the servo to different pulse width.
HIGH SPEED
HIGH VOLTAGE 6V - 8.4V
CORELESS - TITANIUM GEAR
Page 3
ENTER ENTER
ENTER
INC+ DEC-
ENTER
ENTER
INC+
DEC-
INC+
ENTER
DEC-
INC+ and DEC- to choose the right neutral pulse
and to choose the right frequency and enter swing/manual screen.
INC+ DEC-
INC+ and DEC- to change the amplitude of the pulse width.
and to change the pulse width and
INC+ DEC-
Page 4