Related Manuals for Shopsmith 10-ER
Summary of Contents for Shopsmith 10-ER
- Page 1 Owner’s Guide v1.01 MAGNA 10ER restored by Everett L. Davis – 2016 - Donated without cost to the worldwide Shopsmith Community...
-
Page 2: Table Of Contents
SHAPER ........................................16 FLEXIBLE SHAFT ......................................16 MORTISING ....................................... 16 JOINTING ........................................16 SAFETY PRECAUTIONS ......................................17 REPAIRS ..........................................17 Owner’s Guide v1.01 MAGNA 10ER restored by Everett L. Davis – 2016 - Donated without cost to the worldwide Shopsmith Community... - Page 3 APPENDIX 1 - WHERE TO GET PARTS TODAY ..............................29 APPENDIX 2 - NOTES and COMMENTS ................................29 IN APPRECIATION ....................................... 30 Owner’s Guide v1.01 MAGNA 10ER restored by Everett L. Davis – 2016 - Donated without cost to the worldwide Shopsmith Community...
- Page 4 Owner’s Guide v1.01 MAGNA 10ER restored by Everett L. Davis – 2016 - Donated without cost to the worldwide Shopsmith Community...
-
Page 5: Shopsmith Multi-Purpose Power Tool
Shopsmith Shavings and other communications from the company on new accessories, etc. SETTING UP SHOPSMITH - Unpack carefully and check to see that you have all the parts listed above. Do not release any levers or force any parts until you have read the following instructions: Assembly of Shopsmith will be facilitated if you first clean off the rust-resisting compound with which certain parts have been coated for shipment. -
Page 6: Attaching Headrest
Hold the tubular ways with the left hand (to prevent falling), loosen the base plate knob, and lower slowly until the ways rest on the bench. Unbolt base plate and remove Shopsmith from the crate. -
Page 7: Attaching Motor Switch
ADJUSTING PULLEYS AND BELTS - Attach motor pulley (small pulley closest to motor) on the motor shaft. With Shopsmith in its horizontal position - be sure setscrews on motor bracket rods are tight - align motor pulley with headstock pulley by adjusting motor until the two are in line. -
Page 8: Headstock
Ball bearings can be easily injured or ruined by improper handling. The ball bearings used in Shopsmith should not be changed without proper tools. If a bearing needs replacement, return the entire drive sleeve assembly or the spindle and quill assembly, to your dealer who will arrange for factory repair. -
Page 9: Carriage
Allen screws on under side. Two table slots allow the miter gauge to be used on either side of the saw blade. The Shopsmith exclusive miter gauge design permits rapid attachment or removal of a miter gauge face extension. -
Page 10: Tailstock
This permits the extension and bar to be rotated slightly and aligned with the saw table. TAILSTOCK - When used as a lathe in spindle-turning operations, Shopsmith departs from the conventional by using a fixed tailstock (Fig. 9) and a movable headstock. -
Page 11: Faceplate Turning
Place saw table rods into carriage holes and lower to the point where they can be locked by the carriage knobs. Locate Owner’s Guide v1.01 MAGNA 10ER restored by Everett L. Davis – 2016 - Donated without cost to the worldwide Shopsmith Community... - Page 12 Owner’s Guide v1.01 MAGNA 10ER restored by Everett L. Davis – 2016 - Donated without cost to the worldwide Shopsmith Community...
- Page 13 Owner’s Guide v1.01 MAGNA 10ER restored by Everett L. Davis – 2016 - Donated without cost to the worldwide Shopsmith Community...
-
Page 14: Saw Adjustments
Place it in right hand miter slot. Square the face of miter gauge with left hand miter slot using a carpenter's square. Owner’s Guide v1.01 MAGNA 10ER restored by Everett L. Davis – 2016 - Donated without cost to the worldwide Shopsmith Community... -
Page 15: Disc Sander
HORIZONTAL DRILL PRESS - In addition to handling work too large or too awkward to be worked on a vertical drill press, Shopsmith, as a horizontal drill press, will do many jobs with greater precision and ease. Jacobs chuck is placed on the spindle and held in place by tightening its setscrew. -
Page 16: Miscellaneous Applications
SCRATCH BRUSHING - Steel or brass-wire scratch brushes in various degrees of fineness can be used to produce either a rough- textured or fine satin finish on metals, depending on type of brush and operating speed. Support on a Shopsmith 1/2 inch arbor. -
Page 17: Safety Precautions
Model Number appears on name plate. Complete Serial Number stamped on nameplate on head-stock. Your Shopsmith dealer may have to order the part from the factory. If so, please allow sufficient time for transportation. MOTORS If your motor requires service, return it to your dealer who will have it repaired at the motor manufacturer's local repair station. -
Page 18: Parts Illustration - Table And Accessories
PARTS ILLUSTRATION – TABLE AND ACCESSORIES Owner’s Guide v1.01 MAGNA 10ER restored by Everett L. Davis – 2016 - Donated without cost to the worldwide Shopsmith Community... -
Page 19: Parts Illustration - Main System - Headstock - Way Tubes, Etc
PARTS ILLUSTRATION – MAIN SYSTEM – HEADSTOCK – WAY TUBES, ETC. Owner’s Guide v1.01 MAGNA 10ER restored by Everett L. Davis – 2016 - Donated without cost to the worldwide Shopsmith Community... -
Page 20: Repair Parts And Assemblies Parts List
REPAIR PARTS AND ASSEMBLIES PARTS LIST Owner’s Guide v1.01 MAGNA 10ER restored by Everett L. Davis – 2016 - Donated without cost to the worldwide Shopsmith Community... -
Page 21: Shopsmith Accessories Parts List
SHOPSMITH ACCESSORIES PARTS LIST Owner’s Guide v1.01 MAGNA 10ER restored by Everett L. Davis – 2016 - Donated without cost to the worldwide Shopsmith Community... -
Page 22: Shopsmith Optional Accessories
SHOPSMITH OPTIONAL ACCESSORIES Owner’s Guide v1.01 MAGNA 10ER restored by Everett L. Davis – 2016 - Donated without cost to the worldwide Shopsmith Community... -
Page 23: 10Er Table Exploded Parts View Only - 11 X 17 - No Labels
10ER TABLE EXPLODED PARTS VIEW ONLY – 11 x 17 - NO LABELS Owner’s Guide v1.01 MAGNA 10ER restored by Everett L. Davis – 2016 - Donated without cost to the worldwide Shopsmith Community... -
Page 24: 10Er Exploded Parts View Only - 11 X 17 - No Labels
10ER EXPLODED PARTS VIEW ONLY – 11 x 17 - NO LABELS Owner’s Guide v1.01 MAGNA 10ER restored by Everett L. Davis – 2016 - Donated without cost to the worldwide Shopsmith Community... -
Page 25: 1953 Montgomery Wards Power Tool Catalog - Shopsmith Accessories
1953 Montgomery Wards Power Tool Catalog - Shopsmith Accessories Page 46 Owner’s Guide v1.01 MAGNA 10ER restored by Everett L. Davis – 2016 - Donated without cost to the worldwide Shopsmith Community... -
Page 26: 1953 Montgomery Wards Power Tool Catalog - Shopsmith Accessories
1953 Montgomery Wards Power Tool Catalog - Shopsmith Accessories Page 47 Owner’s Guide v1.01 MAGNA 10ER restored by Everett L. Davis – 2016 - Donated without cost to the worldwide Shopsmith Community... -
Page 27: 1953 Montgomery Wards Power Tool Catalog - Shopsmith Accessories
1953 Montgomery Wards Power Tool Catalog - Shopsmith Accessories Page 48 Owner’s Guide v1.01 MAGNA 10ER restored by Everett L. Davis – 2016 - Donated without cost to the worldwide Shopsmith Community... -
Page 28: 1953 Montgomery Wards Power Tool Catalog - Shopsmith Accessories
1953 Montgomery Wards Power Tool Catalog - Shopsmith Accessories Page 49 Owner’s Guide v1.01 MAGNA 10ER restored by Everett L. Davis – 2016 - Donated without cost to the worldwide Shopsmith Community... -
Page 29: Appendix 1 - Where To Get Parts Today
APPENDIX 1 - WHERE TO GET PARTS TODAY In one year from the time I am writing this, the MAGNA Shopsmith 10E introduced in 1947 will be 70 years old. The 10ER came next. While the Magna Engineering Corporation and the subsequent owners and manufacturers of this machine no longer exist, many of the machines themselves survive to this day and are in daily use by those of us who value what this remarkable machine is capable of as we strive to preserve, restore and use them. -
Page 30: In Appreciation
This restored March 1953 MAGNA 10ER manual is donated without cost to the worldwide Shopsmith Community and is not to be sold. IN APPRECIATION Many thanks are given to James Grange Sr.