Eques Greeter User Manual

Greeter
DIGITAL DOOR VIEWER
User Manual
Main Components
Bracket Outdoor Camera Indoor Screen
1 piece 1 piece 1 piece
Charger
USB Cable Screws
1 piece 1 piece 2 pairs ( 4 peices)

Safety Guideline

Please do not expose this product to high temperatures or
high humidity, or an environment with large amounts of dust,
or any other grimy substance.
Please do not forcibly press the main indoor display screen
lens, or the outdoor lens, as this may cause hardware damage.
Be sure to use extreme caution during the installation
process, and do not forcibly pull on the cables. Avoid
scratching or cracking the cable; cable damage due to
improper installation is not covered under regular warranty.
Please only use the charger included in this package, as using
other chargers with different specifications may lead to
battery damage, or may cause system damage.
When installing the MicroSD card, cable connectors, and data
wires, please read through the instructions carefully. Pay
attention to insertion direction to prevent incorrect
installation, which can lead to hardware or system damage.
When selecting screws with which to install the outdoor unit,
be sure to choose ones that are appropriate for the door
thickness; avoid unsuitable screws that could lead to product
damage.
Installation
1 2
Take off the front door's Peel off the strip on the back
existing peephole, or drill a of the outdoor unit
new hole into the door
(suggested hole diameter
is approximately 0.8 inch/
20 mm)
Note: Before installing the outdoor unit, it is
recommended that the selected screws are
fastened into the bracket by lightly twisting
for a few revolutions. This will allow for more
convenient installation later on.

Troubleshooting Common Errors

At the time of installation, if the screws are not restrained
1.
in place or the unit is not sturdy, the incorrect screws may
have been selected. If this is the case, reconfirm the door
thickness, and replace the screws.
2. If a message such as "DID NOT INSTALL PROPERLY"
"VIDEO LOST" appears when pressing the Preview key,
the cable connected to the main unit may not be fully
connected or may be damaged, recheck all cable
connections. If all connections are properly in place,
the problem may lie with a damaged cable, in which case
the cable or unit need to be replaced.
3 4
Based on the door thickness With the doorbell button at
select the appropriate length the bottom of the unit, place
screws, and after several it against the door; be aware
hand-turns replace the unit that the unit is not yet fully
over the peephole opening secured into place, and could
fall off
5 6
Straighten out the cable, Tighten the screws, securing
feeding it from the bracket the bracket into position.
out through the slot in the Ensure that the "Up" arrow
middle on the back of the bracket
is pointing upward

Technical Parameters

Indoor Screen Dimensions:
5.3in x 3in x 0.7in ( 135.5mm x 76.5mm x 18.7mm )
Outdoor Camera Dimensions:
2.4in x 2.4in x 0.6in ( 60mm x 60mm x 14mm )
or
Applicable door thickness: 1.4in - 4.1in (35mm ~ 105mm)
Applicable peephole: 0.5in - 2.3in (13mm ~ 58mm)
When choosing screws to install the outdoor camera, you must
know your door's thickness.
Notes:
For the door thickness between 1.4in - 2.6in (35mm ~ 65mm),
choose 1.4in (35mm) short screws;
For the door thickness between 2.6in - 3.7in (65mm ~ 95mm),
choose 2.6in (65mm) long screws;
For the door thickness above 3.7in (95mm), use your own M3
screws around 3.2in (80mm).
7 8
Squeeze the cable from the Insert the MicroSD memory
outdoor unit through the slit card into the main indoor unit
on the back of the main unit (pay attention to the memory
card's orientation)
9 10
9
Installation is complete, and
Fasten the main indoor unit
onto the bracket; if the cable the unit is ready for use
is sticking out, bend it into
the form of an "S"