Table of Contents
Advertisement
USER MANUAL
NI TSM-101x
NI TSM-1012, NI TSM-1015, NI TSM-1017 Touch Screen Monitors
This document describes the features of the National Instruments TSM-101x and contains
information about installing and operating the device.
The NI TSM-101x series is a resistive touch screen, color LCD flat panel monitor for
industrial applications. There are three models in the NI TSM-101x series: the NI TSM-1012,
NI TSM-1015, and the NI TSM 1017.
The front of the NI TSM-101x monitor is a flat panel LCD screen surrounded by an aluminum
frame. A small keypad on the rear of the monitor controls the onscreen display (OSD).
1
1. 9 to 36 V terminal block
2. 9 to 36 V lockable DC jack
3. VGA port
Contents
Safety Guidelines...................................................................................................................... 2
General Safety Precautions............................................................................................... 2
Installation Precautions..................................................................................................... 2
Anti-Static Precautions..................................................................................................... 3
Maintenance and Cleaning................................................................................................3
Verifying the Kit Contents........................................................................................................ 3
Optional Accessories.........................................................................................................4
Installing Software Drivers....................................................................................................... 4
Supported Operating Systems........................................................................................... 4
Selecting Touch Screen Modality on Windows................................................................ 4
Enabling the Embedded UI on NI Linux Real-Time........................................................ 6
Connecting the NI TSM-101x to Power................................................................................... 6
Wiring the Terminal Block................................................................................................6
Connecting an Adapter to the Power Jack........................................................................ 7
Figure 1. NI TSM-101x Connector Panel
2
3
4
4. DVI-D port
5. DisplayPort connector
6. USB port
5
6
Advertisement
Table of Contents
Related Manuals for National Instruments NI TSM-1012
Summary of Contents for National Instruments NI TSM-1012
-
Page 1: Table Of Contents
The NI TSM-101x series is a resistive touch screen, color LCD flat panel monitor for industrial applications. There are three models in the NI TSM-101x series: the NI TSM-1012, NI TSM-1015, and the NI TSM 1017. -
Page 2: Safety Guidelines
Do not drop or insert any objects into the ventilation openings of the monitor. • If considerable amounts of dust, water, or fluids enter the monitor, turn off the power supply immediately, disconnect the power cord, and contact National Instruments. • Do not strike or exert excessive force on the LCD panel. -
Page 3: Anti-Static Precautions
Verify that the following components are included in the NI TSM-101x kit. Note Do not remove the plastic cover over the LCD screen until the NI TSM-101x is properly installed. • Touch Screen Stylus • USB A-to-A Cable • RS-232 Cable NI TSM-101x User Manual | © National Instruments | 3... -
Page 4: Optional Accessories
If any of the items on the packing list are missing or damaged, contact National Instruments immediately. Optional Accessories Table 1. Optional accessories for the NI TSM-101x monitor Accessory NI TSM-1012 NI TSM-1015 NI TSM-1017 783674-01 Stand 783672-01 783673-01 V-Mount Kit 783675-01 —... - Page 5 Control Panel. Figure 2. The PenMount Icon The Control Panel dialog box appears. Double-click the PenMount 6000 icon on the Device tab. The calibration screen appears. Select the Standard Calibration button. NI TSM-101x User Manual | © National Instruments | 5...
-
Page 6: Enabling The Embedded Ui On Ni Linux Real-Time
Follow the onscreen instructions. Touch the screen at the five specified points to calibrate. Enabling the Embedded UI on NI Linux Real-Time The NI TSM-101x monitor requires a USB connection for touch-screen modality on NI Linux Real-Time targets. Note NI Linux Real-Time does not support RS-232 touch screen modality. Use a USB cable to connect the monitor to the target and complete the following steps to enable touch screen modality. -
Page 7: Connecting An Adapter To The Power Jack
Installation requires a Phillips screwdriver and may require additional accessories. Caution When mounting, do not overtighten the retention screws. Dimensions The following figures show the dimensions for the three models of NI TSM-101x. NI TSM-101x User Manual | © National Instruments | 7... - Page 8 Figure 4. NI TSM-1012 Dimensions 40.50 mm 16.80 mm 32.60 mm 4-RIO 322.20 mm 10.30 mm 248.00 mm 262.20 mm 186.40 mm 161.10 mm 210.60 mm 8 | ni.com | NI TSM-101x User Manual...
- Page 9 Figure 5. NI TSM-1015 Dimensions 43.20 mm 378.50 mm 13-H3-COUNTERSUNK 306.00 mm 19.50 mm 230.00 mm 303.00 mm NI TSM-101x User Manual | © National Instruments | 9...
-
Page 10: Panel Mounting
Cut out a section of the panel that corresponds to the dimensions of the rear panel of the monitor as shown in the following table. Table 2. Suggested Cutout Dimensions Model Height Width NI TSM-1012 243.8 mm (9.60 in.) 303.8 mm (11.96 in.) NI TSM-1015 284.6 mm (11.20 in.) 360.1 mm (14.18 in.) NI TSM-1017 323.0 mm (12.72 in.) -
Page 11: Cabinet Or Rack Mounting
Slide the monitor with the attached bracket into a rack or cabinet. Insert and tighten the retention screws to secure the system into a cabinet or rack as shown in the following figure. NI TSM-101x User Manual | © National Instruments | 11... -
Page 12: Mounting To A Monitor Stand
Figure 8. Securing the Cabinet or Rack Bracket Mounting to a Monitor Stand The NI TSM-101x monitor has standard Video Electronics Standards Association (VESA) mounting holes in the rear panel. The holes are designed for M4 screws and set at 100.0 mm × 100.0 mm (3.94 in. -
Page 13: Mounting With The V-Mount Kit
Mounting with the V-Mount Kit You can use the V-Mount Kit to mount the NI TSM-1012 to a wall, ceiling, desk, or other surface. The V-Mount has a 0 to 90 degree adjustable hinge to optimize the viewing angle of the monitor. -
Page 14: Dvi-D Connector
Table 3. VGA Connector Pinouts Description GREEN BLUE GROUND GROUND GROUND GROUND GROUND DDCDAT HSYNC VSYNC DDCCLK DVI-D Connector The DVI connector connects to a display device with DVI interface. The pins on the connector have the standard pin numbering configuration for a DVI-D connector. Table 4. -
Page 15: Displayport Connector
The DisplayPort connector transmits a digital signal to compatible DisplayPort devices. The pins on the connector have the standard pin numbering configuration for a DisplayPort connector. Table 5. DisplayPort Connector Pinouts Description ML_L3N ML_L3P ML_L2N NI TSM-101x User Manual | © National Instruments | 15... -
Page 16: Usb For Touch Panel Connector
Table 5. DisplayPort Connector Pinouts (Continued) Description ML_L2P ML_L1N ML_L1P ML_L0N ML_L0P C_DDI0_DP_AUXP C_DDI0_DP_AUXN C_DDI0_DP_HPD USB for Touch Panel Connector The USB touch panel connector enables touch screen modality from the monitor to the host machine. The pins on the connector have the standard pin numbering configuration for a USB- A connector. -
Page 17: Display Panel Keypad
The following display menu options are listed in the order they appear onscreen. • Auto Adjust—Automatically adjusts the LCD screen position. • Phase—Adjusts the input signal (analog only). • Clock—Adjusts the dot clock position. • Display Position—Adjusts the Gamma. NI TSM-101x User Manual | © National Instruments | 17... -
Page 18: System Menu
NI trademarks. Other product and company names mentioned herein are trademarks or trade names of their respective companies. For patents covering NI products/technology, refer to the appropriate location: Help»Patents in your software, the file on your media, or the National Instruments Patent Notice at . You can find patents.txt ni.com/patents...