Summary of Contents for AMICOCIRC AMICO 20-4-130
- Page 1 AMICOCIRC Intelligent Frequency Conversation Circulation Pump Handbook www.xpowerwaterpumps.com www.xpowerwaterpumps.com...
- Page 3 UE - Correct Disposal Of This Product Index This symbol identifies important notes regar- ding the correct disposal of the device. By disposing of this product correctly you will Cautions Pag. 01 help ensure that the waste undergoes the ne- cessary treatment, recovery and recycling, and thus prevent potential negative effects on Product Overview...
- Page 4 Cautions Warranty Amico Circulator 1. Read and understand this user manual before installation and opera- Warranty certificate tion of the product. 2. The warning sign marks notes whose non-observance will endanger Thank you for purchasing this pump, designed and ma- your health or the functioning of the device.
- Page 5 Problems Solving Product Overview WARNING!!! 1. AMICO Before any electrical work, make sure the power switch is in the off position. The AMICO Circulator is synonymous of quality and safety. Quiet and powerful, it is designed to ensure a considerable energy sav- ing.
-
Page 6: Installation Instructions
Nomenclature Liquid Temp. Ambient Temp (°C) Min. (°C) Max. (°C) AMICO Lenght from inlet to outlet (mm) Max. lif (m) In & out diameter (mm) Pump model Installation and Usage In domestic hot water system, we recommend to keep the water tem- perature below 65 °C in order to reduce scale. - Page 7 2. Installation of Amico Circulator Technical Data and Dimensions The arrows on the pump housing indicate the direction of liquid flowing through the pump. 1.Technical Data 2.1 Installation (Fig. 1) Supply voltage 230V / -10% +6% / 50Hz-60Hz, PE Motor protection Integrated in the pump head Protection grade IP42...
- Page 8 2.2 Location of Junction Box Performance Fig 3.1 High tem- perature High tem 2.3 Different positions of the Junction Box The junction box can be turned with 90 °C, as a gear. But you can also change the installation position of the box (Figure 3.1).
- Page 9 2.4 Pump Body and Heat Insulation System The "system temperature" must be higher than the "environment tem- SetUp Pump features Function perature", to avoid an excessive condensation on the pump housing. Please refer to the temperature instructions on the product label. Autoadaptation Mode the performance of pump Max.
- Page 10 Electrical Connections Expulsion of air Electric Cable Insert the cables Max diameter 10mm Cable is in the correct or- Min diameter 5mm 0,75mm It means running for 5 minutes The pump is equipped with the function S3, self purging function. After the start of this setting, the air in the pipes (cause of noise and malfunc- tions) wears off after a few minutes.
- Page 11 Operation Instructions System installed with bypass valve 1. Operation Panel 1.1Operating instructions for control panel Auto by-pass Valve Manual by-pass Valve 1) Actual consumption in Watt 2) Lighting set up areas 8.2 By-pass valve 3) Night Mode: ON 4) Automatic Night Mode By-pass valve functions: The bypass valve can ensure a distribution of 5) Change settings Button heat to the water heater, only when all of the heating system valves are...
- Page 12 2. Display Description Note: ◄ When one of the fixed speeds (S1-S2-S3) is running, night mode 1) 2.1 After starting, the led in location 1 (Actual consumption in does not work. Watt) lights. ◄In the event of a power failure, the night mode must be restarted. 2.2 Actual power pump consumption signal.
- Page 13 6. Select Button The AUTO Mode is usually installed in heating systems with double- Press the MODE button once to change the settings one at a time. pipes-stems. The pump modulates the yield according to the actual de- Press the MODE button for eight (8) times to slew the entire cycle of the mand of the pump.
Need help?
Do you have a question about the AMICO 20-4-130 and is the answer not in the manual?
Questions and answers