Cisco NIM-ES2-8 Installing Manual

Cisco NIM-ES2-8 Installing Manual

4-port and 8-port layer 2 gigabit etherswitch network interface module
Hide thumbs Also See for NIM-ES2-8:

Advertisement

Installing the Cisco 4-Port and 8-Port Layer 2
Gigabit EtherSwitch Network Interface Module
Installing the Cisco 4-Port and 8-Port Layer 2 Gigabit EtherSwitch Network
Interface Module
August 19, 2016
This guide describes how to install the Cisco 4-Port and 8-Port Layer 2 Gigabit EtherSwitch Network Interface
Module (Cisco NIM-ES2-4 and Cisco NIM-ES2-8) in the Cisco 4000 Series Integrated Services Router (ISR)
and how to connect the NIM-ES2 to your network.
Contents
This guide contains the following sections:
About the Cisco 4-Port and 8-Port Layer 2 Gigabit EtherSwitch Network
Interface Module
This section describes the Cisco NIM-ES2-4 and Cisco NIM-ES2-8. It contains the following sections:
Cisco NIM-ES2-4 and Cisco NIM-ES2-8 Overview
The Cisco 4-Port and 8-Port Layer 2 Gigabit EtherSwitch Network Interface Modules are switch modules to
which you can connect Cisco IP phones, Cisco wireless access point workstations, and other network devices
such as video devices, routers, switches, and other network components.
The following Cisco 4-Port and 8-Port Layer 2 Gigabit EtherSwitch Network Interface Modules are supported
on the Cisco 4000 Series ISRs:
• 4-ports non-POE Layer 2 Gigabit Ethernet Switch Network Interface Module (NIM-ES2-4)
• 8-ports non-POE Layer 2 Gigabit Ethernet Switch Network Interface Module (NIM-ES2-8)
• 8-ports POE Layer 2 Gigabit Ethernet Switch Network Interface Module (NIM-ES2-8-P)
Multiple Cisco NIM-ES2-4 and Cisco NIM-ES2-8 units that can be present on the Cisco 4000 ISR is dictated
by the total NIM slots present in the router.
Note
Cisco 4-Port and 8-Port Layer 2 Gigabit EtherSwitch Network Interface Modules support a maximum of 4K
entries in the MAC table.
The following table lists the maximum number of network modules supported on the router.
Installing the Cisco 4-Port and 8-Port Layer 2 Gigabit EtherSwitch Network Interface Module
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the NIM-ES2-8 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Cisco NIM-ES2-8

  • Page 1 • 8-ports non-POE Layer 2 Gigabit Ethernet Switch Network Interface Module (NIM-ES2-8) • 8-ports POE Layer 2 Gigabit Ethernet Switch Network Interface Module (NIM-ES2-8-P) Multiple Cisco NIM-ES2-4 and Cisco NIM-ES2-8 units that can be present on the Cisco 4000 ISR is dictated by the total NIM slots present in the router.
  • Page 2 Need SM-X-NIM-ADPTR 4331 Need SM-X-NIM-ADPTR 4331 For information about these and other features available in Cisco NIM-ES2-4 and Cisco NIM-ES2-8s, see the Cisco 4-Port and 8-Port Layer 2 Gigabit EtherSwitch Network Interface Module Configuration Guide at the following URL: hhttp://www-author.cisco.com/c/en/us/td/docs/routers/access/interfaces/NIM/software/configuration/guide/4_8PortGENIM.html/ The following modules are available with this release of the hardware: •...
  • Page 3 Installing the Cisco 4-Port and 8-Port Layer 2 Gigabit EtherSwitch Network Interface Module Cisco 8-Port Layer 2 non-POE Gigabit EtherSwitch Netwrok Interface Module Cisco 8-Port Layer 2 non-POE Gigabit EtherSwitch Netwrok Interface Module The below figure, show the Cisco 8-Ports Layer 2 Gigabit EtherSwitch NIM.
  • Page 4: Cisco Nim-Es2-4 And Cisco Nim-Es2-8 Ports

    The Ethernet ports are numbered left to right, top to bottom. The port numbering scheme to configure the ports on the Cisco NIM-ES2-4 and Cisco NIM-ES2-8 includes the port type (such as gi or gigabitethernet for Gigabit Ethernet), and the switch port number. If you are not using the NIM-ADPTR, the slot number is always 0.
  • Page 5 You cannot set the port to Half duplex if the port speed is set to Auto. Cisco NIM-ES2-4 and Cisco NIM-ES2-8 LEDs Cisco NIM-ES2-4 and Cisco NIM-ES2-8 LEDs provide green, amber, and off states for system and port status. The following sections describe LEDs on the service modules: •...
  • Page 6 Table 3: EN LED State System Status The Cisco 4-Port and 8-Port Layer 2 Gigabit EtherSwitch Network Interface Module is not powered Amber The Cisco 4-Port and 8-Port Layer 2 Gigabit EtherSwitch Network Interface Module is powered on and in booting stag.
  • Page 7: Preparing For Installation

    Installing the Cisco 4-Port and 8-Port Layer 2 Gigabit EtherSwitch Network Interface Module Preparing for Installation Preparing for Installation The following sections describe safety warnings, general maintenance guidelines, and safety recommendations that you must read before installing and using the NIM:...
  • Page 8 Installing the Cisco 4-Port and 8-Port Layer 2 Gigabit EtherSwitch Network Interface Module Safety Warnings Danger Before opening the unit, disconnect the telephone-network cables to avoid contact with telephone-network voltages. Statement 1041 Danger Before working on equipment that is connected to power lines, remove jewelry (including rings, necklaces, and watches).
  • Page 9: Preventing Electrostatic Discharge Damage

    Electrostatic discharge can damage equipment and electrical circuitry. Electrostatic discharge occurs when electronic printed circuit cards, such as those used in Cisco service modules are improperly handled and can result in complete or intermittent equipment failure. Always observe the following procedures to prevent...
  • Page 10: Installing And Removing The Cisco 4-Port And 8-Port Layer 2 Nim In A Cisco 4000 Series Isr

    Cisco IOS XE Release 3.15S, Cisco IOS 15.5(2)S, and Cisco IOS XE Release 16.3.1 or a later release is required to install the Cisco NIM-ES2-4 and Cisco NIM-ES2-8-P. To determine the version of Cisco IOS software that is running on your router, log in to the router and enter the show version command: show version Router>...
  • Page 11: Installing The Cisco Nim-Es2-4 And Cisco Nim-Es2-8 In A Cisco 4000 Series Isr

    Remove the blank faceplates installed over the slot you intend to use. Step 3 Push the Cisco NIM-ES2-4 and Cisco NIM-ES2-8 into place until you feel the edge connector seat securely into the connector on the router backplane. The module faceplate should contact the chassis rear panel.
  • Page 12: Power Specifications For The Cisco Nim-Es2-4 And Cisco Nim-Es2-8S

    A 10/100/1000 Gigabit Ethernet (GE) port can be used as an uplink port to connect to another router or a server, or the GE port can trunk to another Cisco NIM-ES2-4 and Cisco NIM-ES2-8 or switch located in the same chassis or in a separate installation.
  • Page 13: Related Documents

    To comply with the Telcordia GR-1089 NEBS standard for electromagnetic compatibility and safety, connect the Cisco NIM-ES2-4 and Cisco NIM-ES2-8 only to intra-building or unexposed wiring or cable. The intra-building port(s) of the equipment or subassembly must not be metallically connected to interfaces that connect to the OSP or its wiring.

This manual is also suitable for:

Nim-es2-4

Table of Contents