Advertisement
29565_800_IB_tri
8/24/06
3:21 PM
Usage Tips
Before using read the important
safety instruction section in front
of the manual.
Charging
Prior to using your shaver for the
first time, put it on charge for 24
hours.
To charge your shaver:
Make sure your shaver is turned
off.
Connect the cord to the shaver and
then the charging adapter to the
electric outlet. A charging indicator
light will come on.
Your shaver cannot be over-
charged, so you can leave it
plugged in and charging between
shaves.
Use only the charging adapter
supplied with the shaver.
Special feature allows you to run
the shaver directly off the cord.
Your shaver will not recharge while
you are shaving, so after shaving
directly from the cord, turn the unit
off and set aside to charge.
Provides up to two weeks worth of
shaving after a one hour charge or
a single shave after five minutes of
charging.
NOTE: It may take up to 3 cycles for
the battery to reach full capacity.
8
Page 8
Model R-800
A blue indicator light shows charging.
A red low-battery indicator illuminates
to show when the shaver needs
recharging. This also indicates
approximately 5 minutes of shaving
time left when indicator first comes on.
Model R-825
A blue lighted fuel gauge displays the
amount of charge remaining in 20%
increments. When only 20% of the
charge remains, the recharge red
warning light illuminates.
Troubleshooting:
If your R-800/825 shaver battery
is completely discharged or the
shaver has not been used for
an extended period of time,
the shaver may not start when
operated using the cord. If this
condition occurs, charge the
shaver for approximately five
minutes before shaving.
Your cord/cordless shaver should
not be used strictly as a cord-
operated shaver, as continued
cord only use will result in
reduction of battery life.
In order to preserve the life of
the batteries, they should be fully
discharged every six months and
then fully charged for 24 hours.
Cleaning & Maintenance
Reassemble head
Cleaning your shaver
to cutter retainer
TO ASSURE OPTIMAL PERFORMANCE,
assembly by aligning
IT IS RECOMMENDED THAT YOU CLEAN
and turning head 1/8
YOUR SHAVER AFTER EACH USE.
turn in the opposite
direction. Repeat this
Detach the handheld unit from the
process for each of
power supply cord before cleaning.
the 3 heads. Clean
The cutting system of this shaver
each head and cutter
was designed to be cleaned by rinsing
set one at a time to
under warm running water or by
prevent mixing cutter
brushing.
components. (These should be kept
as sets). After cleaning, place cutter
Cleaning your Remington
®
branded
retainer assembly in the hair pocket,
shaver is easy.
and secure by turning center knob
approximately 1/4 turn clockwise.
Open the hair
pocket by
Caution: Never put the shaver com-
pressing the
pletely under water. Do not use any
release button
aggressive cleansing agent as this
and rotating
may destroy the shaver coatings.
away from the
body of the shaver. You may blow
out the stubble thoroughly, or rinse
the shaver head in water. Rinse
both sides of the head assembly.
At Least Once a Week:
For more complete
cleaning, remove
the cutter retainer
assembly from the
Caution: Do not remove or replace
the head assembly while shaver is
hair pocket by turn-
running or plugged into an electrical
ing the center knob
outlet as it may cause damage to the
approximately 1/4
unit's cutters. The shaver shall not be
turn counter clockwise. Hold cutter
used until it has dried.
retainer assembly as shown, and
remove head by turning approxi-
mately 1/8 turn in the direction
shown. Brush clean both the head
and the cutter.
To clean and lubricate your shaver's
cutters and head assembly, apply
Remington
®
Shaver Saver
®
(SP-4)
Lubricant. The lubricant helps
remove hair clippings while reduc-
ing wear. A quick spray after each
shave keeps your shaver operating
at peak performance.
Worn or damaged parts should be
replaced with Remington
®
branded
replacement parts only.
9
Advertisement
