Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Noam NMC3
- Page 2 * Detailed accessory list for each speakers, controller and amplifier can be found inside each component’s manual. Introduction Both NMC3 & NMB3 were built as a system. All included components of the unit; Speakers, amplifier & controller were designed and tuned to match one another and function as a full audio system.
-
Page 3: Specifications
Waterproof: N3 Speakers: The pair of N3 speakers features 3.5” Water-Proof Full Range Speaker, cased in a high-quality Aluminum housing. Your N3 speakers will fit any Motorcycle / ATV handlebar at 7/8”, 1” & 1.25” diameter. Your NA2 amplifier is an IPX6 waterproof level. Though this is a Marine IPX6 rated amplifier, * THIS MANUAL AND OTHERS CAN ALSO BE whenever possible, mount the amplifier in a... - Page 4 More about the NA2 Amplifier A. Installation Applications: The NMC3 / NMB3 is designed for operation with 12 volts, negative-ground electrical The NA2 amplifier is state of the art Class D amplifier designed to systems. Using this product in systems with positive ground and/or voltages other than provide great amplification in a small space for your motorcycle / ATV...
-
Page 5: Troubleshooting
Refer to section C TROUBLESHOOTING Problem Cause Solution It just doesn’t Speaker are connected to Refer to section C.5 of sound right the wrong output this owner manual Did you remember to press Controller wasn’t and hold the controller’s power turned ON It just doesn’t button for 3-5 seconds? - Page 6 Power/Protect Indicator: C. Installation Procedure/Connections If you feel unsure about installing this system yourself, have it installed by a qualified technician. There are two status indicator lights on the end panel of the amplifier. Before installation Disconnect the NEGATIVE battery post connection and secure 1.
- Page 8 Thank you for choosing NOAM N3 speakers. We invested a lot of thought, time and e ort into 3.5” Motorcycle Speaker 100W/50W Power Handling the creation of these speakers. all while great sound 3.5” Motorcycle Speaker 100W/50W Power Handling and ease of use are on our mind to lead the way.
-
Page 9: Best Practice
Step 1: Best practice: Choose the correct rubber insert’s Make sure you size for your handlebar and place it around screw each side’s M5 screw the handlebar. evenly. note: 1.25” handlebar doesn’t require any rubber inserts for installation. rubber insert Step 2: Speaker Rotation: place the speaker’s bracket... - Page 10 Importnt featurs of the N3 Speaker Wiring: Please read before first use The N3 has long wiring, well protected in a wiring sleeve. - You can cut the wiring to a desired length for a clean installation. Handlebar Fitment: But, make sure to do so only after you finished installing your entire Your N3 speakers can be mounted audio system, including its amplifier.
-
Page 11: Bluetooth Receiver
Visit us at www.noamaudio.com and sign up to our newsletter to stay tuned. we are always working new exciting products just for you! Bluetooth Receiver www.noamaudio.com... -
Page 12: Installation
QC before being packed. The NR controller has a DIN If at any given time you have any plug. This plug can be connected directly to the NOAM NA2 & NA4 questions or concerns, please feel free amplifiers. Remote power triggering: to contact us at: sales@noamaudio.com... -
Page 13: Supplied Hardware
On phone select (NOAM NR) to pair device. plate Once a device is paired each time this device is seen by the NOAM NR it will outomatically reconnect to the device. If no device is present the NOAM NR outomatically goes into pairing mode and will present itself as discoverable for the next device present. - Page 14 Installation Installation Mounting yor NOAM NR STEP 2: Peel off the 3M sticker's cover The NR controller has 3 mounting options: 1. Dash or Flush (Rear) mount 2. Surface mount 3. Handlebar mount (not available in the NUTV5 and NUTV5-S units) STEP3: Place the NR on a perfectly flat surface.