Subscribe to Our Youtube Channel
Summary of Contents for Cineo Quantum c80
- Page 1 User Guide Revision 1.2 — October, 2017 Information and speci cations in this document are subject to change without notice. w w w . c i n e o l i g h t i n g . c o m...
- Page 2 For color-accurate white light, choose the CCT as resistant and includes an integrated power supply you would with any Cineo fixture, using the WHITE for easy setup. rotary control or the second DMX channel.
-
Page 3: General Notes
Ensure that the yoke lock is correctly tightened when manipulating Qc80 in the required orientation for safety purposes. Ensure the Cineo Qc80 is operated within an ambient temperature range of -20 to +50°C (-4 to 122°F). - Page 4 System Components, Connections and Controls All connectors and system controls for the Cineo Qc80 are located on the back of the unit. In addition to its full color heads-up display, optically encoded rotary knobs give access to menu selections and local control inputs.
- Page 5 Power The Qc80 unit is controlled by an internal power supply. 110 – 220VAC is provided to the unit via a locking IEC connector, located on the back control panel. NOTES: 1. Ensure the power cable is disconnected before servicing. 2.
-
Page 6: Color Space
Color Space The Qc80 uses two separate LED engines to independently generate accurate white light, variable from 2700K to 6500K, and an extended RGB gamut for broad saturated color space. The CIE 1931 diagram below illustrates the Qc80 color space. Controls Setup of the Qc80 is can be accomplished either using the large Red DIM knob with the control and... - Page 7 Here are examples of how to accurately match camera stops to dimming levels in Local Mode: Local Dimming: The Rule of 20 (0-100 scale) Increase output 1 Stop: Add 20 units (fc/lux is doubled) Decrease output 1 Stop: Subtract 20 units (fc/lux is reduced 50%) Adjust ½...
- Page 8 Here are examples of how to accurately match camera stops to dimming levels in DMX Mode: DMX Dimming: The Rule of 50 (0-255 scale) Increase output 1 Stop: Add 50 DMX values (fc/lux is doubled) Decrease output 1 Stop: Subtract 50 DMX values (fc/lux is reduced 50%) Adjust ½...
- Page 9 The DMX pin wiring is as follows: • Pin 1: Signal Common • Pin 2: Data – • Pin 3: Data + • Pin 4: Spare • Pin 5: Spare Wireless DMX Control The Qc80 built-in wireless receiver runs on CRMX / Lumen Radio protocol which can receive signals from CRMX and some WDMX transmitters.
-
Page 10: Mounting Options
USB Port An A-type USB port is included on the control panel for installation of software updates. It can also supply 5 VDC, 500ma power to attached devices. Refer to installation instructions supplied with software upgrade. Mounting Options In addition to the attached mounting yoke, (4) attachment points are included of the back of the fixture. All of these points can accept a 3/8”x 16 threaded eyebolt. -
Page 11: Burning Injuries
Warnings, Disclaimers and Warranty Risk of Electric shock / Risk of Fire Do not open. To reduce the risk of electric shock, do not remove cover (or back). No user- serviceable parts inside. Refer servicing to qualified service personnel. Burning Injuries Be aware of high temperatures in excess of 50°C inside the fixture during and after use. - Page 12 If the Product fails to work as warranted, Cineo Lighting will, in its sole discretion, repair or replace the Product with a new or remanufactured Product that is at least equivalent to the original Product.
- Page 13 Specifications are subject to change without notice. Cineo Lighting, Cineo Quantum c80 are registered trademarks of Cineo Lighting, Inc. ©2017 Cineo Lighting, Inc. v11.15.17 Cineo Lighting P.O. Box 808 El Granada, CA 94018 Silicon Valley | Los Angeles | London info@cineolighting.com...
Need help?
Do you have a question about the Quantum c80 and is the answer not in the manual?
Questions and answers