Download  Print this page

Advertisement

C
I
I S C O
N T E L L I G E N C E
M
O U N T I N G
Console
Routers
Quick Start Guide
, C
A B L I N G
Cisco Intelligence Engine 2100 Series
Routers
1
T
O
W
AKE
UT
HAT
2
R
M
ACK
OUNT THE
3
C
ONNECT
4
R
S
UN THE
ETUP
E
2 1 0 0 S
N G I N E
,
A N D
DRIVE
0
DRIVE
1
Hub
Y
N
OU
EED
H
ARDWARE
C
ABLES
P
ROGRAM
E R I E S
S
E T U P
Routers

Advertisement

Table of Contents

   Related Manuals for Cisco 2100 series

   Summary of Contents for Cisco 2100 series

  • Page 1 N G I N E E R I E S O U N T I N G A B L I N G A N D E T U P Cisco Intelligence Engine 2100 Series DRIVE DRIVE Console Routers Routers...
  • Page 3: Product Documentation

    Cisco Intelligence Engine 2100 Series 1 Cisco Intelligence Engine 2100 Series Configuration Registrar Manual (for more detailed information about subjects covered in this guide) 1 Release Notes for Cisco Intelligence Engine 2100 Series Configuration Registrar Hardware Appliance 1 Cisco Intelligence Engine 2100 Series...
  • Page 4 Take Out What You Need (continued) Cables and Power Cord 1 yellow Ethernet 10BaseT cable (to connect to a 10BaseT hub) 1 flat, light-blue console cable with 1 RJ-45 adapter, labeled TERMINAL (RJ-45-to-DB-9) 1 black power cord Rack-Mount Kit 2 L mounting brackets (left and right) 4 M4 Phillips countersunk-head screws 4 12-24 x 3/4-inch Phillips binder-head screws 4 10-32 x 3/4-inch slotted binder-head screws...
  • Page 5 Rack Mount the Hardware LIN K 10 0M bp s LIN K 10 0M bp s CO NS ET HE RN DR IVE ET 0 ET HE RN DR IVE ET 1 Phillips machine screws Installing Rack Mount To install the IE2100 Series in a rack: Hardware Step 1 Measure the rack to verify that the system...
  • Page 6: Connect Cables

    Connect Cables Cisco Intelligence Engine 2100 Series DRIVE DRIVE Console Routers Routers Routers Connecting the Ethernet and Cisco Intelligence Engine 2100 Series Console Cables LINK 100M bps Use the console cable in the accessory kit to connect LINK 100M bps...
  • Page 7 Connect Cables (continued) Power receptacle Power switch AC power connector Connect the Power Cable Step 1 Verify that the Power switch is set to OFF. Step 2 Connect the black power cable to the power receptacle on the rear panel of the IE2100 Series.
  • Page 8 Run the Setup Program This section explains how to run the setup program Primary DNS nameserver IP address IP address of DNS server that to configure the system. IE2100 Series uses for name/IP-address Step 1 Boot the system without a configuration. resolution.
  • Page 9 Run the Setup Program (continued) Verify Configuration Registrar If you have reached the Configuration Registrar Home page, you have verified the is Running successful installation on the Configuration Once the system has been installed and configured, Registrar. you can verify the installation of the Configuration Registrar by following these steps: Step 1 Go to a different computer and bring up a...
  • Page 12 VCO are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries. All other brands, names, or trademarks mentioned in this document or Web site are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company.

Comments to this Manuals

Symbols: 0
Latest comments: