PRYME Radio Product PRYMEBLU BT-PTT-M User Manual

PRYMEBLU® BT-PTT-M
Push-to-Talk Button User's Guide
For use with Zello Push-to-Tak app on both Android or Apple iOS
smartphones and tablets
Model No. BT-PTT-M
Made in Taiwan
PRYME® and PRYME BLU® are trademarks owned by PRYME Radio Products,
Brea CA. All other product or service names are the property of their respective owners.
© 2017 PRYME Radio Products, Brea CA. All Rights Reserved
Battery Replacement
The BT-PTT-M is powered by a pre-installed CR2032 coin cell type battery. The battery should last
up to two years before needing to be replaced; however, operating time can vary depending on
usage cycle and the age and condition of the battery. Always turn the power switch on the
BT-PTT-M to the off position when the device is not in use to help preserve battery life.
The BT-PTT-M is powered by a pre-installed CR2032 coin cell type battery. The battery should last
Whenever you turn the BT-PTT-M on, the LED Status Indicator will blink once to indicate power.
up to two years before needing to be replaced; however, operating time can vary depending on
In the event that the LED does not blink when the power switch is turned on, it may be necessary
usage cycle and the age and condition of the battery. Always turn the power switch on the
BT-PTT-M to the off position when the device is not in use to help preserve battery life. to replace the coin cell battery with a new one.
Whenever you turn the BT-PTT-M on, the LED Status Indicator will blink once to indicate power.
To replace the battery, follow these steps:
In the event that the LED does not blink when the power switch is turned on, it may be necessary
to replace the coin cell battery with a new one.
1. Remove the Velcro Fastener from the unit and set it aside.
2. Using a small jeweler's-sized Phillips screwdriver, remove the four screws located on the rear
To replace the battery, follow these steps:
of the unit.
1. Remove the Velcro Fastener from the unit and set it aside. 3. Remove the rear housing to expose the battery holder.
2. Using a small jeweler's-sized Phillips screwdriver, remove the four screws located on the rear
4. Locate the battery holder inside of the device. Remove the old battery from the battery holder.
of the unit.
You can use the small screwdriver or a ballpoint pen to push the battery out of the holder if needed.
3. Remove the rear housing to expose the battery holder.
5. Insert a new CR2032 3-volt coin cell battery into the battery holder, observing proper polarity.
4. Locate the battery holder inside of the device. Remove the old battery from the battery holder.
The positive side of the battery (marked with a "+" sign) should face away from the circuit board.
You can use the small screwdriver or a ballpoint pen to push the battery out of the holder if needed.
6. Re-install the rear housing, making sure that the Volume Up and Volume Down button covers
5. Insert a new CR2032 3-volt coin cell battery into the battery holder, observing proper polarity.
on the sides of the unit are properly aligned.
The positive side of the battery (marked with a "+" sign) should face away from the circuit board.
6. Re-install the rear housing, making sure that the Volume Up and Volume Down button covers
7. Re-install the screws using the Phillips screwdriver.
on the sides of the unit are properly aligned.
8. Re-install the Velcro Fastener.
7. Re-install the screws using the Phillips screwdriver.
8. Re-install the Velcro Fastener.
If you are not comfortable replacing the battery in the unit yourself, PRYME offers a convenient
If you are not comfortable replacing the battery in the unit yourself, PRYME offers a convenient
battery replacement service. Contact PRYME tech support for further details.
battery replacement service. Contact PRYME tech support for further details.
3
Controls and Connection
VOLUME UP / DOWN BUTTONS
These buttons control the volume
of your handset up and down.
CHANNEL UP / DOWN BUTTONS
Pressing these buttons will select
the next or previous contact in the
Zello app.
POWER SWITCH
This slide switch is used to turn the
BT-PTT-M on and off. Set to the switch to
the off position to save battery life when
the PTT is not being used.
App Setup (ZELLO - iOS)
To get the Zello app on your phone,
install Zello from your Zello@Work
network, or download the app from
the Apple App Store.
1. Make sure that your phone's Bluetooth is enabled, and that the BT-PTT-M is power on.
The phone and PTT must be nearby each other (with 30 feet).
2. Open Zello and go to: Settings > PTT Button > Wireless Zello Button.
3. Make sure that the "Wireless Button Service" is
turned on by sliding the button to the right.
4. Press and release the PTT button on the BT-PTT-M.
5. Select "PTT-M" from the list of PTT devices shown
on the screen.
6. Open the Talk screen in Zello (the screen with a big
round button). Pressing the PTT button the Push-to-Talk
device should now cause Zello to transmit.
7. Pressing the Channel Up or Channel Down buttons
on the BT-PTT-M should cause the Zello app to cycle
through your contact list.
8. Pressing the Volume Up or Volume Down buttons
on the BT-PTT-M should adjust the volume on the
phone handset.
STATUS LED
This light will momentarily flash
blue when the BT-PTT-M is turned
on or when the Push-to-Talk
function is engaged.
VOLUME UP / DOWN BUTTONS
These buttons control the volume
of your handset up and down.
PTT BUTTON
Press this button to
activate the Push-to-Talk
function of the Zello app.
VELCRO FASTENER
The Velcro fastener is used to
secure the BT-PTT-M to your
person or any other convenient
location during use.
2
4