Advertisement
SETUP
Remove all packing materials from the GEMINI.
Mount the GEMINI with its included Yoke (see "T" above) and Junior Pin ("Z") to a rigging or support system rated for the weight of the fixture and its accessories
(not included). Always comply with applicable local regulations. Use supplemental safety equipment (e.g. safety chain or cable, not included).
WARNING: Keep the air intakes ("U") and the air exhaust space ("X") clear of blockage. Allow more than 25 cm [10 inches] of clear air space from the rear of the
GEMINI to the nearest obstruction. Use only covers and accessories approved by Litepanels
Plug the powerCON end of a provided AC power cable into the AC Power Input ("N") on the fixture. Plug the other end of the power cable into a mains power
outlet. Switch the ON / OFF Power Switch ("A") to the "ON" position. The GEMINI is ready for operation.
OPERATION
CCT MODE (Default)
The default operation mode of the GEMINI is CCT Mode. In CCT Mode, the knobs behave as follows:
•
Turn the DIM / INT Knob ("C") clockwise to increase intensity (%). Turn counterclockwise to decrease intensity.
•
Turn the CCT / SAT Knob ("D") clockwise to raise the Correlated Color Temperature, or CCT (Kelvin or K). Turn counterclockwise to lower CCT.
•
Turn the +/- GRN / HUE / MENU Knob ("E") clockwise to add green color offset. Turn counterclockwise to subtract green color offset.
HSI MODE
•
Turn the DIM / INT Knob ("C") clockwise to increase intensity (%). Turn the knob
counterclockwise to decrease intensity.
•
Turn the CCT / SAT Knob ("D") clockwise to increase color saturation (%). Turn the knob
counterclockwise to decrease color saturation.
•
Turn the +/- GRN / HUE / MENU Knob ("E") clockwise to increase the color hue value (°)
(see "Figure 1: Hue Value Guide"). Turn counterclockwise to decrease the color hue value.
Push the +/- GRN / HUE / MENU Knob ("E") to access menu items,
including color mode operation options and system settings.
TROUBLESHOOTING
Behavior
There is no light output.
Power/Status Indicator flashes
green when fixture is powered on.
Light turns off.
Light turns off.
Light is on.
Light is on.
Light turns off.
Light intensity is
decreased by 50%.
Light intensity is
decreased by 50%.
The light is not operating
normally.
Litepanels
®
A Vitec Group brand
Power/Status Indicator
green solid on
Fixture is operating normally.
green flashes
Fixture is operating normally.
red solid on
Input Over Voltage Fault
red solid on
Input Under Voltage Fault
red flash, pause,
Input Under Voltage Warning
(repeat)
red flashes (2X), pause,
Over Temperature Warning
(repeat)
red flashes (4X), pause,
Over Temperature Fault
(repeat)
green solid on
Fan is OFF or under DMX
control.
red flash, pause,
Fan is malfunctioning.
red flashes (3X), pause,
(repeat)
red flashes (other)
Fixture is malfunctioning.
Register your product online at www.litepanels.com
, and ensure that they do not obstruct the air intakes or exhaust.
®
120˚
180˚
240˚
Figure 1: Hue Value Guide
Condition
Adjust dimmer knob to change brightness.
Take no action. The green flashing stops
shortly after the fixture has been powered on.
Turn fixture off; change power source.
Turn fixture off; change power source.
Change power source.
Turn the dimmer down to 0% and allow
fixture to cool. Check fan and vents.
Turn the dimmer down to 0% and allow
fixture to cool. Check fan and vents.
Change fan settings, if desired.
Check the fan for stoppage or blockage.
Replace fan module if fan is permanently
disabled.
Note the red flashes pattern and contact
service at litepanels.com/support
60˚
GREEN
YELLOW
0˚
CYAN
RED
BLUE
MAGENTA
300˚
Recommended Action
Vitec Videocom Inc.
info@vitecvideocom.com
Advertisement
