Strongway 46217 Owner's Manual

Strongway 46217 Owner's Manual

2-ton long ram double piston jack

Advertisement

Quick Links

8-TON LONG RAM
DOUBLE PISTON JACK
OWNER'S MANUAL
WARNING:
Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before
operating. Failure to follow the safety rules and other basic safety precautions may result in
serious personal injury.
Item# 46217
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 46217 and is the answer not in the manual?

Questions and answers

Summary of Contents for Strongway 46217

  • Page 1 8-TON LONG RAM DOUBLE PISTON JACK OWNER’S MANUAL WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury. Item# 46217...
  • Page 2: Intended Use

    Thank you very much for choosing a Strongway product! For future reference, please complete the owner’s record below: Model: _______________ Purchase Date: _______________ Save the receipt, warranty and these instructions. It is important that you read the entire manual to become familiar with this product before you begin using it.
  • Page 3: Important Safety Considerations

    IMPORTANT SAFETY CONSIDERATIONS DO NOT OPERATE OR REPAIR THIS EQUIPMENT WITHOUT READING THIS MANUAL. To maintain the Service Jack and user safety, the responsibility of the owner is to read and follow these instructions.  Inspect the service jack for proper operation and function. ...
  • Page 4 * Position the Jack Position the jack to only lift on the areas of the vehicle as specified by the vehicle manufacturer. * Always Use Jack Stands After lifting the vehicle always support the load with appropriately rated vehicle Jacks stands before working on the vehicle.
  • Page 5 ASSEMBLY 1. Familiarize yourself with the jack. 2. Use handle (36) to Turn release valve (43) counterclockwise on full turn to the open position. 3. Line up the handle to the handle socket located on the side of the jack, then insert the handle inside the handle socket.
  • Page 6 4. Secure the handle in place inside the handle socket. Without any weight on the jack, cycle the lift up and down several times to insure the hydraulic system is operating properly. (Perform to the Air Purge Procedure before first use.) SYSTEM AIR PURGE PROCEDURE IMPORTANT: BEFORE FIRST USE...
  • Page 7 3. Purge air trap in the system by opening the attached oil vent, do not remove oil vent. Oil vent Is to stay open at all times when in use. (Oil vent is closed during shipping) For units with rubber oil plugs: {With a flat blade screwdriver, push the oil fill plug slightly to the side to purge trapped air from system.
  • Page 8: Before Use

    BEFORE USE 1. Before using this product, read the owner's manual completely and familiarize yourself thoroughly with the product and the hazards associated with its improper use. 2. Perform the air purge procedure. (See previous instructions for system purge procedure.) 3.
  • Page 9 WARNING: STOP PUMPING WHEN THE RAM RISES TO THE RED STOP MARK ON THE RAM. THIS WILL PREVENT THE JACK FROM POSSIBLE MALFUNCTION AND IMPROPER USE. CAUTION: NEVER WIRE, CLAMP OR OTHERWISE DISABLE THE LIFT CONTROL VALVE TO FUCTION BY ANY MEANS OTHER THAN BY USING THE OPERATOR'S HAND.
  • Page 10: Maintenance Instruction

    MAINTENANCE INSTRUCTION If you use and maintain your equipment properly, it will give you many years of service. Follow the maintenance instructions carefully to keep your equipment in good working condition. Never perform any maintenance on the equipment while it is under a load. Inspection You should inspect the product for damage, wear, broken or missing parts (e.g.: pins) and that all components function before each use.
  • Page 11 TO ADD JACK OIL: 1. Position the jack on level as shown and lower the ram. 2. Remove the oil plug. 3. Fill the oil case until oil level is just beneath the lower rim of the oil fill hole.
  • Page 12 4. Replace oil plug. 5. Perform the Air Purge Procedure. TO REPLACE JACK OIL: 1. Position the jack on level as shown and lower the ram. 2. Open release valve by turning handle counter-clockwise (4 full turns). 3. Remove the oil fill plug. 4.
  • Page 13 Position the jack on level ground and with the ram in the lowered position. 7. Fill the oil case until oil level is just beneath the lower rim. KEEP DIRT AND OTHER MATERIAL CLEAR WHEN POURING. 8. Replace oil plug. 9.
  • Page 14: Additional Warnings

    ADDITIONAL WARNINGS:  DO NOT USE MOTOR OIL IN THE JACK.  ONLY USE ANTI-FOAMING JACK OIL.  ALWAYS USE A GOOD GRADE HYDRAULIC JACK OIL.  DO NOT USE HYDRAULIC BRAKE FLUID, ALCOHOL, GLYCERINE, DETERGENT, MOTOR OIL OR DIRTY OIL.
  • Page 15: Assembly Diagram

    ASSEMBLY DIAGRAM...
  • Page 16: Parts List

    PARTS LIST Index # Description Part No. Qty. T30306-01 T30306-06 Wire ring T30306-10 T30306-12 Split washer T30306-11 Y-Ring T30306-09 Wire ring T30306-03 Cylinder QYL3.2-12 Copper Washer T90403-35 Tube GB308 Ball QYL8-13 Copper Washer QYL8-10 Pump Cylinder QYL8-09 Seal Ring QYL8-28 O-Ring QYL8-27 Back up Ring...
  • Page 17: Replacement Parts

    Safe Operating Temperature is between 40°F – 105°F (4°C - 41°C) REPLACEMENT PARTS For replacement parts Customer Service at 1-800-222-5381. Not all equipment components are available for replacement; illustrations provided are a convenient reference of location and position in the assembly sequence. When ordering parts the following will be required: Model Number, Serial Number and Description.
  • Page 18 Northern Tool and Equipment Company, Inc. ("We'' or '"Us'') warrants to the original purchaser only ("You'' or “Your”) that the Strongway product purchased will be free from material defects in both materials and workmanship, normal wear and tear excepted, for a period of one year from date of purchase. The foregoing warranty is valid only if the installation and use of the product is strictly in accordance with product instructions.

Table of Contents