Table of Contents
Advertisement
USER MANUAL
Trademarks
All brand and product names are trademarks or registered trademarks of
Maka GPS Technologies Group. In association with Maka GPS
Technologies Private Limited (Singapore), Maka GPS Technologies
Sdn. Bhd. (Malaysia), Maka Technologies Group (H.K.) Limited. and
Maka Corporation USA
Inc.
The information in this manual is subject to change without notice
.
www.makagps.com
2/2018. R1.2
1
© 2017 Maka Technologies Group. All Rights Reserved.
Advertisement
Table of Contents
Related Manuals for Morbella TX1
Summary of Contents for Morbella TX1
- Page 1 USER MANUAL Trademarks All brand and product names are trademarks or registered trademarks of Maka GPS Technologies Group. In association with Maka GPS Technologies Private Limited (Singapore), Maka GPS Technologies Sdn. Bhd. (Malaysia), Maka Technologies Group (H.K.) Limited. and Maka Corporation USA Inc.
-
Page 2: Safety Information
Safety information To prevent injury to yourself and others or damage to your device, read the safety information about your device before using the device. Warning Failure to comply with safety warnings and regulations can cause serious injury or death. Do not use damaged power cords or plugs, or loose electrical sockets Unsecured connections can cause electric shock or fire. - Page 3 Use manufacturer-approved batteries, chargers, accessories, and supplies •Using generic batteries or chargers may shorten the life of your device or cause the device to malfunction. They may also cause a fire or cause the battery to explode. •Use only Maka GPS Technologies Group-approved battery and charger specifically designed for your device.
- Page 4 •Extreme temperatures can damage the device and reduce the charging capacity and life of your device and battery. •Prevent the battery from coming into contact with metal objects, as this can create a connection between the + and – terminals of your battery and lead to temporary or permanent battery damage.
- Page 5 Caution Failure to comply with safety cautions and regulations can cause injury or property damage Do not use your device near other electronic devices Most electronic devices use radio frequency signals. Your device may interfere with other electronic devices. Do not expose the device to heavy smoke or fumes Doing so may damage the outside of the device or cause it to malfunction.
- Page 6 Do not store your device in very hot or very cold areas. It is recommended to use your device at temperatures from 0 °C to 60 °C and humidity from 10% to 80% Doing so may cause the screen to malfunction, result in damage to the device, or cause the battery to explode.
- Page 7 •Leaving batteries unused over time may reduce their lifespan and performance. It may also cause the batteries to malfunction or explode, or cause a fire. •Your device may wear out over time. Some parts and repairs are covered by the warranty within the validity period, but damages or deterioration caused by using unapproved accessories are not.
- Page 8 Correct disposal of this product (Waste Electrical & Electronic Equipment) (Applicable in countries with separate collection systems) This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not be disposed off with other household waste.
- Page 9 Disclaimer Some content and services accessible through this device belong to third parties and are protected by copyright, patent, trademark and/or other intellectual property laws. Such content and services are provided solely for your personal non-commercial use. You may not use any content or services in a manner that has not been authorised by the content owner or service provider.
- Page 10 content or service will remain available for any period of time. Content and services are transmitted by third parties by means of networks and transmission facilities over which Maka GPS Technologies Group has no control. Without limiting the generality of this disclaimer, Maka GPS Technologies Group expressly disclaims any responsibility or liability for any interruption or suspension of any content or service made available through this device.
-
Page 11: About This Manual
About this manual This device provides high quality digital recording device using Maka’s high standards and technological expertise. This user manual is specially designed to detail the device’s functions and features. •Please read this manual before using the device to ensure safe and proper use. -
Page 12: Table Of Contents
Overview of your TX1 FHD Digital Roadcorder Device Layout / Button Function Understanding of your TX1 FHD Digital Roadcorder Buttons Status Icons Standard Packaging of your TX1 FHD Digital Roadcorder Package Contents Installation for your TX1 FHD Digital Roadcorder Installation Charging the Battery... - Page 13 Table of Contents Operation of your TX1 FHD Digital Roadcorder Auto Power Off Beep Sound 30–31 Language Frequency LCD Time Out 32-33 Exposure Anti-Shaking Delay Shutdown 34-35 Format Default Setting Version PHOTO SETTING Capture Mode Resolution 37-38 Sequence Quality 38-39...
-
Page 14: Product Specifications
Product Specifications Sensor 3MP Sony323 sensor Lens Fixed focus, 4 layer glasses Lens Aperture F=2.2, f=2.1 , FOV : 170° NTK96658 External Memory Class 10 or above TF card( SDHC specification up to 64G) Gravity sensor Sensitivity low/medium/high/OFF 3.0 inch 16:9 TFT LCD Audio Built-in high sensitivity microphone/speaker Motion detect... -
Page 15: Getting Started
Getting Started Overview of your TX1 FHD Digital Roadcorder Device Layout / Button Function Micro Sd Card Slot 07. Right Arrow (Scroll) UP Arrow (Scroll) 08. Manual Lock Button Menu Button 09. Mode Change Button Down Arrow (Scroll) 10. Ok Button (Stop/Rec/Enter) 11. -
Page 16: Understanding Of Your Tx1 Fhd Digital Roadcorder
Getting Started Understanding your TX1 F HD Digital Roadcorder and Buttons Buttons Button Functions Press and hold to turn the device on or off. Hot Keys during recording mode: • Press to manual turn off / on LCD screen when recording. -
Page 17: Status Icons
Getting Started Understanding your TX1 FHD Digital Roadcorder and Buttons Status Icons © 2017 Maka Technologies Group. All Rights Reserved. -
Page 18: Standard Packaging Of Your Tx1 Fhd Digital Roadcorder
Getting Started Standard Packaging of your TX1 FHD Digital Roadcorder Package contents Check the product box for the following items: • TX1 Front Camera • Operating Manual • Mounting holder for camera (3M Stick / Suction Type) • Car Charger (5V output type) ... -
Page 19: Installation For Your Tx1 Fhd Digital Roadcorder
Getting Started Installation of your TX1 FHD Digital Roadcorder Installation 1 Fixing the camera to the window mount It is compulsory for window mount to be fixed up before using the device in a car. Make sure that you place the recorder in an appropriate place, so as not to obstruct the driver’s view. -
Page 20: Charging The Battery
Getting Started Installation of your TX1 FHD Digital Roadcorder Charging the battery Use the charger to charge the battery before using it for the first time. Charge the device by connecting front camera via the USB car charger. Use only Maka- approved chargers, batteries, and cables. -
Page 21: Inserting A Memory Card
Getting Started Installation of your TX1 FHD Digital Roadcorder Inserting a memory card Your device accepts memory cards with maximum capacities of 64 GB. Depending on the memory card manufacturer and type, some memory cards may not be compatible with your device. -
Page 22: Removing / Formatting Memory Card
Getting Started Installation of your TX1 FHD Digital Roadcorder Removing the memory card Before removing the memory card, first unmounts it for safe removal. On the device 1 Press on the button to stop the device from recording (Blue light will stop blinking. -
Page 23: Operation Of Your Tx1 Fhd Digital Roadcorder
Getting Started Operation of your TX1 FHD Digital Roadcorder Turning the device on and off Press and hold the Power button for a few seconds to turn on the device. A welcome message will be displayed on screen as shown in the image below. -
Page 24: Resolution
Getting Started Operation of your TX1 FHD Digital Roadcorder VIDEO/SYSTEM SETTNG Access the following settings to change the device’s video recording quality. The better the quality, the higher the capacity of the sd card used is higher. Resolution 1 Press OK to stop recording. -
Page 25: Hdr
Getting Started Operation of your TX1 FHD Digital Roadcorder It is important to make backup copies of all important data stored on the device. The manufacturer’s warranty does not cover loss of data resulting from user actions. 1 Press OK to stop recording. -
Page 26: Motion Detector
Getting Started Operation of your TX1 FHD Digital Roadcorder 5 Press on the Up or Down button to make your selection 6 Press on OK to confirm your entry and exit to setting 7 Press on button twice to exit Setting and back recording mode... -
Page 27: Record Audio
Getting Started Operation of your TX1 FHD Digital Roadcorder Record Audio You may choose to turn off the microphone so that all the recorded videos will be muted. 1 Press OK to stop recording. 2. Press once to enter into video setting... -
Page 28: Gravity Sensor
Getting Started Operation of your TX1 FHD Digital Roadcorder 2. Press once to enter into video setting 3 Press on Up or Down button to navigate to the function that shows Date Stamp 4 Press on OK to enter and see : ON/OFF... -
Page 29: Date / Time
Getting Started Operation of your TX1 FHD Digital Roadcorder Date/ Time Setup Access the following settings to change the device’s time and date. If the battery remains fully discharged or removed from the device, the time and date is reset. -
Page 30: Auto Power Off
Getting Started Operation of your TX1 FHD Digital Roadcorder 6 Press on OK (if selection On) to confirm your entry and enter to set the number plate 7 Press on the Up or Down button to make your selection and OK button to make the next entry... -
Page 31: Beep Sound
Getting Started Operation of your TX1 FHD Digital Roadcorder Beep Sound This function is to turn on/off of the the button sound. 1 Press OK to stop recording. 2. Press once to enter into video setting 3 Press on Up or Down button to navigate to the function that shows... -
Page 32: Frequency
Getting Started Operation of your TX1 FHD Digital Roadcorder 8 Start recording by pressing OK button 9 Stop recording by pressing OK button again Frequency Please set according to the local power supply respectively; 50Hz or 60Hz. 1 Press OK to stop recording. -
Page 33: Exposure
Getting Started Operation of your TX1 FHD Digital Roadcorder 6 Press on OK to confirm your entry and exit to setting 7 Press on button once to exit Setting and back recording mode 8 Start recording by pressing OK button... -
Page 34: Anti-Shaking
Getting Started Operation of your TX1 FHD Digital Roadcorder Anti-Shaking 1 Press OK to stop recording. 2. Press once to enter into video setting 3 Press on Up or Down button to navigate to the function that shows Anti- Shaking... -
Page 35: Format
Getting Started Operation of your TX1 FHD Digital Roadcorder 6 Press on OK to confirm your entry and exit to setting 7 Press on button once to exit Setting and back recording mode 8 Start recording by pressing OK button... -
Page 36: Default Setting
Getting Started Operation of your TX1 FHD Digital Roadcorder Restore Factory Setting (Default Setting) Set the system parameters to the default value of the device origin install at. By doing so, any setting which needed to change accordingly to user preference will have to set the setting again. -
Page 37: Photo Setting
Getting Started Operation of your TX1 FHD Digital Roadcorder PHOTO SETTING Capture Mode This setting allowed you to set pre-time the photo delay being taken when pressing the shot button 1 Press M button once enter into Photo Mode 2 Press on Menu... -
Page 38: Sequence
Getting Started Operation of your TX1 FHD Digital Roadcorder 6 Press on OK to confirm your entry and exit out to photo setting 7 Press OK button for photo shooting Sequence This function enable shooting of 3 photo in one single shot. -
Page 39: Sharpness
Getting Started Operation of your TX1 FHD Digital Roadcorder 5 Press on the Left or Right button to make your selection 6 Press on OK to confirm your entry and exit to photo setting 7 Press on M twice to exit Setting... -
Page 40: Color
Getting Started Operation of your TX1 FHD Digital Roadcorder 3 Press on Left or Right button to navigate to the function that shows White Balance 4 Press on OK to enter showing AUTO/DAYLIGHT/CLOUDY/TUNGSTEN/FLUORESCENT 5 Press on the Left or Right button to make your selection... -
Page 41: Iso
Getting Started Operation of your TX1 FHD Digital Roadcorder This function enabled to set the light sensitivity of the photo to be taken. Recommended to use as (AUTO) 1 Press M button once enter into Photo Mode 2 Press on Menu... -
Page 42: Playback Mode (Video/Photo)
Getting Started Operation of your TX1 FHD Digital Roadcorder Playback Mode (Video) 1 Stop recording by pressing on the OK button 2 Press M button twice to enter into playback Mode 3 Press on the Up or Down button to navigate thru the video files... -
Page 43: Delete / Protectfiles
Getting Started Operation of your TX1 FHD Digital Roadcorder Delete / Protect Files To delete, protect for one or all file 1 Stop recording by pressing on the OK button 2 Press M button twice to change from recording to playback mode 3 Press UP or Down button to navigate thru the files. -
Page 44: General Troubleshooting
General Troubleshooting Question Reason Solution The captured image 1 MicroSD card might be Reformat the card or is not stored full or maulfunction. replace a new MicroSD 2 Image is not saved before Make sure to stop recording the power outage. before shutting down. -
Page 45: General Troubleshooting
General Troubleshooting Question Reason Solution No image is displayed on a 1 Cable plug might not be 1 Ensure AV/HDMI cable is plug into high-definition TV screen plugged in properly. the TV properly. 2 Wrong TV Input mode 2 Refer to the back panel of your TV to Track the correct TV input.