Advertisement
Quick Links
Advertisement
Related Manuals for Radionics K6300-CNCII
Summary of Contents for Radionics K6300-CNCII
- Page 1 K6100 / K6300-CNCII Central Network Controller User Guide 17317 Ver 1.2/48569B...
- Page 2 K6100-CNC User Guide 17317 Ver 1.2/48569B Page 2 © 2001 Radionics...
-
Page 3: Table Of Contents
6.4 PIN Reader Duress ............................. 9 7.0 Clock Synchronize..................9 8.0 Initialize/Download to Site ..............10 8.1 What is an Initialize/Download? ......................10 8.2 Download Procedure..........................10 Figures Figure 1 Front Panel............................4 K6100-CNC User Guide © 2001 Radionics Page 3 17317 Ver 1.2/48569B... -
Page 4: Introduction
‘updates’ when required. This is a small ‘packet’ of information that the door controller can understand, and used to adjust its own database accordingly. An example would be a new K6100-CNC User Guide 17317 Ver 1.2/48569B Page 4 © 2001 Radionics... -
Page 5: Notation
Note: You should ask your installer to provide you with a list of ‘numbers’ for each site, door controller, door and zone on your system. The Personnel ID number is displayed for each keyholder in the Readykey for Windows Personnel application as ‘Record Number’. K6100-CNC User Guide © 2001 Radionics Page 5 17317 Ver 1.2/48569B... -
Page 6: Administration Readers
PC is left disconnected for a long time. The length of time depends entirely on the rate transactions come into the CNC from the Door Controllers. The message will clear when the CNC has room for 1100 transactions. K6100-CNC User Guide 17317 Ver 1.2/48569B Page 6 © 2001 Radionics... -
Page 7: Priority 2 - Communications Errors
If a * appears instead of = then the site is currently online. If there are no updates for a site that is currently online, then the CNC display will show K6100-CNC User Guide © 2001 Radionics Page 7 17317 Ver 1.2/48569B... -
Page 8: Priority 3 - Monitoring
Backup operation or if the PC is particularly busy which means it cannot communicate with the CNC properly. 5.4.5 Priority 4 - Updates SITE sss=nnnnn SITE sss*nnnnn See the description above. K6100-CNC User Guide 17317 Ver 1.2/48569B Page 8 © 2001 Radionics... -
Page 9: Alarms
Note: If you have a multi-PC Readykey for Windows system, then you should take care that the time on each PC is the same - no attempt will be made by Readykey for Windows to modify the time on other PCs. K6100-CNC User Guide © 2001 Radionics Page 9 17317 Ver 1.2/48569B... -
Page 10: Initialize/Download To Site
To commence the download operation, from within the Initialize and Download screen (Installer: Utilities: Initialize and Download) select the correct Division (if applicable) and Site for the door controller(s) being downloaded to. K6100-CNC User Guide 17317 Ver 1.2/48569B Page 10 © 2001 Radionics... - Page 11 ** MONITORING ** or a non-dial-up site. At this point you should confirm the downloads success by verifying that keyholders can gain access as programmed through doors on the door controller/site. K6100-CNC User Guide © 2001 Radionics Page 11 17317 Ver 1.2/48569B...
- Page 12 K6100-CNC Notes © 2001 Radionics, a division of Detection Systems, Inc. 17317 Ver PO Box 80012, Salinas, CA 93912-0012, USA 1.2/48569B K6100-CNC Customer Service: (800) 538-5807 User Guide Page 12 of 12...