1. Manuals
  2. Brands
  3. ALFRA Manuals
  4. Saw
  5. 22413.110
  6. Instruction manual

ALFRA 22413.110 Instruction Manual

185mm metal cutting saw
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
185mm METAL CUTTING SAW

INSTRUCTION MANUAL

Double Insulation
Original instruction

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 22413.110 and is the answer not in the manual?

Questions and answers

Summary of Contents for ALFRA 22413.110

  • Page 1: Instruction Manual

    185mm METAL CUTTING SAW INSTRUCTION MANUAL Double Insulation Original instruction...

  • Page 2: Table Of Contents

    TABLE OF CONTENT Safety rule…………………………………………………………………………………………………….…2 Additional safty rules for metal cutting saw …………………………………………………………………7 Assembly and Adjustment instruction ……………………………………………………………………….7 Installing a New Saw Blade …………………………………………………………………………………..7 Laser …………………………………………………………………………………………………………….9 Cutting Depth Adjustment ……………………………………………………………………………………10 Operation…………………………………………………………………………………………………….…11 Guide ruler …………………………………………………………………………………………………...11 Chip Removal………………………………………………………………………………………………….12 Replacing Carbon Brushes ………………….……………………………………………………………..13 Maintenance and Servicing………………….……………………………………………………………..13 Troubleshooting …………………………….……………………………………………………………….14 Specifications……………………………………..……………………………………………………………14...
  • Page 3 b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded. c) Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
  • Page 4 tool accidentally. d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. e) Maintain power tools.
  • Page 5 Causes and Operator Prevention of Kickback: Kickback is a sudden reaction to a pinched, bound or misaligned saw blade, causing an uncontrolled saw to lift up and out of the workpiece toward the operator. When the blade is pinched or bound tightly by the kerf closing down, the blade stalls and the motor reaction drives the unit rapidly back toward the operator.

  • Page 6: Additional Safety Instructions

    c) Lower guard manually only for special cuts such as “plunge cuts” and ” compound cuts.”Raise lower guard by retracting handle and as soon blade enters the material, the lowerguard must be released. For all other sawing, the lower guard should operate automatically.

  • Page 7: Additional Safty Rules For Metal Cutting Saw

    ADDITIONAL SAFETY RULES OF METAL CUTTING SAW CAREFULLY READ THE FOLLOWING SAFETY WARNINGS PRIOR TO CONNECTING THE METAL CUTTING SAW TO POWER. 1. Must keep the safety device in the fixed position, and work according to the order. Never wedging or binding the safety device below and must use it.
  • Page 8 free of any defect or damage.Ensure the saw is disconnected from Power. 1. Pull out the height wrench (A) Open the base (B) refer as Fig.1 2. Take out Hex wrench(A) The size for Hex wrench is M6(B) refer as Fig.2 3.

  • Page 9: Laser

    5. Set Up the outer flange on the spindle of blade Use the Hex wrench to lock the shaft screw(B) And need push the safety lever(A) to lock the shaft screw and fixthe blade. Refer as Fig.5 Usage for bevel 1.
  • Page 10 ALIGNING THE LASER GUIDE LINE DANGER: Laser radiation.Avoid direct eye contact with light source. WARNING: Use of controls or adjustments or performance of procedures other than those specified herein may resuit in hazardous radiation exposurs.When you adjust the laser please don’t tune on switch.Fig.9 Otherwise starting the blade can be dangerous.

  • Page 11: Cutting Depth Adjustment

    CUTTING DEPTH ADJUSTMENT 1. Pull up & lossen the Lock Lever(A) first Fig.13 2. Lift the back of the saw away from the baseplate until the approximate depth is achieved. 3. Ensure the Lock Lever(A) Fig.14 is tightened securely after the depth adjustment is made. To adjust the lock and unlock positions(if necessary) simply pull the lever towards the hand-grip of the saw, rotate it slightly as required.

  • Page 12: Guide Ruler

    DIRECTION OF SAWING Please align the right side’s cut in front Of base with a level cutting line of workpiece For longitudinal sawing. THE GUIDE RULER The guide ruler can be used to go on straight sawing precisely, sliding the workpiece, and fixing at the front of base with wing nut.

  • Page 13: Replacing Carbon Brushes

    1. Unscrew the two Knob Bolts (A) on the blade housing. As shown in Fig.19 2. Remove chip shield (B). (keeping the Knob bolt screwed on guard.As shown in Fig.20 3. Release the chips. Fig.19 Fig.20 Beware: Always keep the saw away from your body when removing the chip shield, the chips will fall out.

  • Page 14: Troubleshooting

    TROUBLESHOTTING : SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION • Metal cutting saw will • No supply of power. • Check that power is not start. • Brushes worn or sticking available at source. • Disconnect power, open • Switch is faulty. brush caps and ensure brushes •...

  • Page 15: Manufacturer

    Ple ase read the instructions carefully before starting the machine. Wear ear protect ors! Always wear goggles when using the machine. Always keep hands away from the path of the saw blade. Always disconnect the plug from the socket before carrying out any work on the machine. Never expose tool to rain.

Table of Contents