Acewell ACE-64 Series User Manual

ATV/Motorcycle/Scooter
Computer
ACE-6XXX User Manual
ACE-64XX: 9,000rpm
10R-0312652
ACE-65XX: 12,000rpm
ACE-66XX: 15,00rpm
11
8
1
7
6
2
Thanks for purchasing the ATV/Motorcycle/scooter computer; this
manual is specifically designed for ACE-6XXX-XX series. Different series
have different needle tachometer scales, each series has different
models, each model has different LED indicators. You may find that the
photo has a set of LED indicators different from your computer, the
photo is for reference only.
Different series with different needle tachometer scales
are as bellows:

PANEL DESCRIPTIONS

1. Tachometer Scale 6. RESET Button
2. Needle Tachometer 7. MODE Button
3. 1st row: Speedometer 8. RPM Shift Warning Indicator
4. 2nd row: Other functions 9. Bar Temperature gauge
5. Gear Indicator 10. Bar Fuel gauge
11. LED indicators
Different models have different LED indicators, each indicator symbol
means as below:
Left direction indicator/Green Engine oil / Red
N
Neutral Gear /Green
Main-beam headlamp/Blue
R
Right direction indicator/Green Reverse Gear /Red
D
Hazard Warning/ Red Drive Gear /Green
P
Parking/Green Engine coolant temperature/ Red
Direction indicator/Green Rear fog lamp/Amber
Engine in out of use/ Red
Flash Trailer/Green

FEATURES

Needle tachometer, integrated digital functions and 6-10 LED
indicators for different models.
Displays needle tachometer, speedometer, bar temperature and
fuel gauges, gear indicator and one other function simultaneously.
Features a 99 lap timer and an optional cable connected remote
control switch.
Gear indicator which calculates gear by comparing speed and RPM.
An optional air temperature sensor can measure outside
temperature.
Fuel gauge full and empty resistances are fully adjustable and it can
connect to sender units with resistance range up to 990 ohms. In
reserve mode, the fuel gauge is not displayed and fuel symbol lights
when the input wire is connected to -ve. The gauge can be switched
off entirely if not required.
Flexible battery warning voltage setting from 11.0 to 15.0V.
Speedometer can show nearest 1 or 0.1 mph or km/h speed if
required by user. E.g. 100 or 100.5.
Highly visible 12mm shift warning LED indicator.
Allows end user to adjust odometer when the odometer is less than
30km / 18.6 miles.
Universal wheel circumference setting range from 1 to 3999mm.
Includes bracket, RPM sensing wire, hall or reed speed sensor,
fitting kits, wiring harness and temperature sensor.
Excellent water resistant, anti vibration structure and noise
immunity design.
SPECIFICATIONS

Functions

Symbol Specifications
ACE-64XX 9,000rpm
Needle Tachometer
ACE-65XX 12,000rpm
ACE-66XX 15,000rpm
Digital Tachometer RPM 10-19,990 rpm,
Speedometer
Km/h / MPH 2.4-399.9 km/h (248.5 MPH),
2.4-399.9 Km/h (248.5 MPH),
Maximum speed MAX SPD
Average speed AVG SPD 2.4-399.9 Km/h (248.5 MPH),
Temperature 1 0°C-180 °C /32°F-356°F
1
Temperature 2 2 0°C-180 °C /32°F-356°F
0°C-180 °C /32°F-356°F
MAX
Max. Temperature
<0°C display -L-, >180 °C display -H-
Trip meter 1&2 Trip 1&2
0.0-999.9 KM /624.9Miles
0 - 999999 KM, 0-624999 Miles
Odometer ODO
12/24 Hour Clock
AM/PM 0:00' – 11H59' / 23H59'
Riding timer RT
9 0-99H59`59``
TT
Total Riding Time 0-999999H
10
0-999999H
Total Hour meter HRTT
3
Voltage Gauge 8.0-18.0 Volt and battery warnings
V
Gear indicator N, R, 1, 2,...8 gears and off mode
4
Maintain reminder
9999km, 9999 hours or oFF
5 Bar-Temperature 1-7 Bar-graphic or off mode
Bar-Fuel Gauge
Adjustable 10Ω -990Ω, reserve mode, or not displayed
LAP LAP 99 laps
Power Input DC 12V
Tachometer Sensor CDI or Ignition Coil Signal
Speed Sensor Reed or hall Sensor
Temperature Sensor Thermo Sensor
Speed input divider setup 1-199 Pulses
Maximum speed input frequency 7K Hz
Wheel circumference setting 1mm-3999mm
Dimensions 130.6mm x83.4mmx31.3mm
INSTALLATION & PARTS
Main Unit Installation:
Main Unit
Bracket
Rubber Pad
Washer
Spring Washer
Fixing Screw Nut
RPM sensor mounting:
1.Connect either the yellow or white wire to sense the RPM signal.
2.The yellow wire can be wrapped around the spark plug lead.
a.Signal strength from the ignition coil is dependent on coil type.
b.Coil 2-5 turns around spark plug lead, the more turns the stronger the signal. A
weak signal will not show a reading on the screen whereas a very strong signal
will have a reading which is too high or very jittery. If the reading is incorrect
then try putting the 1MΩresistor which is included in the box inline in the
sensor wire.
3.If the signal is still unstable, please try to connect the white wire to either the
ECU rev counter output or to the primary side of the coil or to the pulse wire on
an active spark plug cap.
Speed Sensor Mounting:
ACEWELL has several speed sensors; the unit may include one of them.
If the model is intended to be connected to a gearbox electronic speed
output to obtain the speed reading, no speed sensor will be included.
Reed Speed Sensor and Magnet:
1. This sensor is universal sensor for motorcycle, find a rotating part to
install magnet (for example disk, sprocket or driveshaft) and a location
to install the sensor where it can be aligned to the magnet.
2. Align the center of the magnet to either of the sensor marking lines or
the side of the sensor. The magnet must not travel down the body of
the sensor.
3. Installing the sensor parallel to the vibration direction creates optional
anti-vibration effect.
4. Make sure the gap between the magnet and the sensor is within 8mm.
Max. 8mm Max. 8mm
sensor sensor
Vibration Direction Vibration Direction
Hall Effective Speed Sensor and Magnet:
1. This is universal sensor for ATV or motorcyclefront or rear wheel
installation or motorcycle front wheel installation. For some fitments
an accessory speed sensor holder may need to be purchased.
2. Find a rotating part to install magnet (for example disk, sprocket or
driveshaft) and a location to install the sensor where it can be aligned
to the magnet
3. Align the center of the magnet to center of side face of the sensor.
4. Make sure the gap between the magnet and the sensor is within 5mm.
Specific Hall sensors:
Cable drive adaptors for most bikes originally fitted with cable driven
speedometers or odometers are available. When using these cables it
is necessary to divide the circumference setting by the number of
rotations of the cable per rotation of the wheel.
Thermo Sensor and Sensor Tube:
1. The unit includes a water temperature sensor; you may have to
purchase a suitable water pipe temperature sensor tube to install
the sensor on some bikes.
2. Cut the water pipe, insert the temperature tube into the pipe and
secure it by attached pipe clamps.
3. Screw the sensor into the tube.
4. If your vehicle is fitted with a thermostat that stops water flowing to
the radiator when the engine is cold, you will not get a reading until
the thermostat opens.
5.Custom sensors are available for carburetted bikes to replace the
original sensor.
Wire Remote Control Switch Installation:
1. Install the switch arm on handlebar.
2. Install the switch box to one of 3 fixing holes and adjust switch box to
a suitable angle.
3. Plug the switch box connector into the main unit matching connector.
FUNCTIONS
RPM: Digital Tachometer
1. It displays digital tachometer up to 19,990RPM and displays 19,999
rpm when tachometer is over 20,000rpm..
2. It has 2 wires to pick up RPM signal, the yellow wire is to connect to
Plug,and white wire is for signal from ECU or Ignition coil.
Shift Warning RPM
1. The function enables you to set up a shift warning RPM.
2. A indicator flashes when RPM reaches 500rpm before setting value.
3. Shift warning LED indicator flashes when RPM reaches setting value, and stops
flashing after you shift gear.
Km/H or MPH: Speedometer
1. Displays speed mete r up to 399.9 Km/H or 248.5 MPH.
2. The maximum frequency of software divider is 7K Hz.
3. With a small wheel size and large number of pulses per wheel
revolution it may not be possible to display very high speeds.
MAX: Maximum Speed Meter
Displays highest speed achieved since last Reset operation
AVG: Average Speed Meter
It calculates average speed from last RESET. The AVG is calculated from
TRIP1 be divided by RT.
TRIP 1&2: Trip Meter 1&2
TRIP function accumulates trip distance since last RESET as long as bike/
vehicle is moving.
ODO: Odometer
1. ODO accumulates total distance traveled.
2. ODO datemory and cannot be reset.
RT: Riding Timer
1. Calculates total running time since last RESET.
2. Counter automatically begins with movement.
TT: Total Riding Timer
1. Calculates total riding time from the beginning of the bike.
2. TT data is stored in memory, and cannot be reset.
HRTT: Hour Meter
1. Calculates total engine operation time since installation RESET.
2. Count automatically begins with engine starting.
3. HRTT data is stored in memory, and cannot be reset.
: 12/24 hour Clock
It displays 12 or 24 hour current time.
1 and 2:Temperature Meter 1 & 2
1. It measures and displays from 0°C-180°C / 32°F-356°F.
2. It displays -L-°C or -L-°F when temperature is lower than 0°C(32°F) or disconnected
temperature sensor, and displays -H- °C or –H-°F when temperature is over 180°C or
356°F.
3. User can measure engine temperature with sensor 1 and ambient air temperature with
sensor 2.
4. The bar-temperature and digits of temperature as well temperature LED indicator flash
when the thermo sensor detects temperature higher than the maximum preset
temperature.
2: Low temperature warning of temperature input 2
1. Temperature input 2 has an automatic low temperature warning which requires no setup
when temperature 2 input is switched on in the setup menu and a temperature sensor is
connected to it.
2. The LED indicator and the icon on the LCD flash when temperature drops below 3℃
and stop flashing when the temperature rises above 3℃.
3. The digital temperature meter displays "-L-" when temperature is less than 0℃
MAX TEMP 1& 2: Maximum Temperature 1 & 2
Displays highest temperature achieved since last Reset operation.
: Digital Voltage and Battery Warnings
1. It checks bike's battery and charging systems health.
2. It has 3 modes to be set, b-on, b-oFF and b-HI, all 3 modes range is from 11.0V to 15.0V.
3. The "b-on" means battery warning on voltage, when the voltage falls below this the
LED will flash.
4. The "b-off" means battery warning off voltage, b-off voltage must larger than b-on
voltage.
5. The "b-HI" means battery high voltage, it comes on to warn that the batter has over
charging.
: Gear Indicator
1. The gear indicator calculates gear by comparing speed and RPM then displays gear
position.
2. User has to train the gear indicator before use it.
SCAN: Scan function
1.The 2nd row of LCD data will be changed automatically every preset number of
seconds if the SCAN is selected. The scan period is from 1 to 20 seconds.
2. All functions will be manual operations when SCAN is switched off.
: Fuel Gauge
1. Has 7 bars to indicate how much fuel remains.
2. To use as a fuel gauge, the user enters the sender 'empty' resistance between 10
and 990 ohms and the sender 'full' resistance between 10 and 990 ohms. The
computer produces a linear scale of bars between these two resistances. When less
than 10% fuel remains the gauge will flash and the warning LED if fitted will light.
3. To use as a reserve indicator, connect the reserve switch to the input and put into
"rEs" mode. When the switch pulls the input to –ve the LED warning will light. On
vehicles with temperature based sensors a 68Ω 5W resistor needs to be connected
between the input wire and 12v (switched).
4. If the gauge and warning lamp are not required they can be switched off
: Bar Thermometer*
1.Have 7 bars to indicate engine temperature.
2.The 4th bar counts from bottom be turned on and over temperature LED flashes when
thermometer reaches the preset warning temperature, each +/-15˚C lights on/off a bar
base on the 4th bar.
3.The bar-temperature flashes when the measured temperature is higher than the preset
warning temperature.
Lap Timer
LAP:
1.It can keep up to 99 sets of lap timer of each circle.
2.The function must be operated by an additional wiring remote control
switch or an accessory IR receiver/transmitter or a magnetic field sensor.
Freezing Time for Lap timer:
1.The freezing time is designed to avoid additional count signal during the set time.
2.The set range is from 1 to 20 seconds.