Advertisement
Speed decimal option:
1.User can decide to display speed to 1 or 0.1 mph / km/h.
2.Follow the item 11 of set up mode to option the decimal of speedometer.
: Maintenance Reminder
1.The maintenance reminder can set by either trip meter or hour meter, and
an "Off" mode to switch it off.
2.The trip meter maintenance can be set up to 9999km.
3.The HRT maintenance reminder can be set up to 9999 hours.
BUTTON OPERATIONS
MODE BUTTON
1. Press the MODE button to move between all functions in
sequence as "
" from one function screen to another when the .
speed sensor does not detect any signal input.
2. Press the MODE button to move partial functions in loop sequence
as "
"when speed sensor detects signal input.
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
RESET BUTTON
Reset button cycles through functions in reverse order
DATA RESETTING AND PROGRAMMING MODES
1. Press MODE or RESET button to reach the desired screen then
press RESET button for 2 seconds to reset TRIP 2, MAX SPD, MAX
RPM and MAX data from stored values to zero individually. The
maintain reminder data will be reset to the preset value rather
than zero.
2. The data of Trip 1, AVG & RT will all be reset at the same time when
one of the 3 data functions is being reset.
3. ODO, clock, HRTT and TT data cannot be reset.
RESET
2SEC
Shift Warning RPM Operation
1. Press MODE button to the RPM screen; pull on the throttle until
the desired shift warning RPM.
2. Press RESET button to confirm and set up the shift warning RPM.
3. Bar-graphic tach ometer and warning LED will flash to warning you
shift gear.
4. Press RESET button for 2 seconds at the RPM screen to re-adjust
the shift warning RPM.
Gear Indicator Tranning Operations:
1. If using a rear wheel or gearbox speed sensor, put bike on a rolling road or
securely mounted centre stand, if measuring front wheel speed the following
can only be done if the vehicle is moving.
2. Change the LCD screen to display digital RPM.
3. Press and hold MODE button for 2 seconds to go into the number of gears
setting mode.
4. Gear indicator flashes the default 0 gears.
5. Press RESET button to select the number of gear, user can select 4-8 gears or
"0" to disable the gear function.
6. Press MODE button to confirm the number of gears and go to the number
gear ratio setting mode.
7. It displays and flashes "1", shift bike's gear to the 1st gear, run the engine to
between 2000-4000RPM.
8. Hold the speed and the RPM for about 5 seconds until the "-"flashing. The
flashing "-"after the gear "1" means the 1st gear be set.
9. Press MODE button to confirm the set and go to the 2nd gear setting.
10. It displays and flashes "2", shift bike's gear to the 2nd gear, run the engineto
between 2000-4000RPM.
11. Hold the speed and the RPM for about 5 seconds until the "-"flashes. The
flashing "-"after the gear "2" means the 2nd gear is set.
12. Press MODE button to confirm the setting and go to next gear setting.
13. Repeat the same operations as items 11-14 to set other gears until the last
gear is set. Press MODE button to return to normal mode.
14. At gear indicator setting mode, press and hold MODE button for 2 seconds
to abort the setting if you need to re-set at any setting screen.
Optional Remote Control Switch for LAP timer
1. The remote control switch has 2 buttons: MODE and LAP. The MODE button
has the same function as on the main unit.
2. Press and hold the LAP button for 2 seconds to go into the LAP mode.
3. LAP Record operations:
a. In LAP mode, press LAP button to convert start or stop the LAP recording
function, each press of MODE button records a set of data LAP and
displays LAP timer for 3 seconds then changes display to speed mode
automatically, press and hold the LAP button for 2 seconds to go out LAP
mode and return to normal mode.
b. The first data of recording function will be renewed by new data when lap
exceeds 99 laps, then each new data renews earliest data one by one.
LAP review operations:
1. In the LAP mode, press MODE button to review the 1st stored data, it
displays number of lap and lap timer.
2. Press the RESET button to switch between lap timer of the same LAP; each
press of the MODE button displays data for the next lap.
3. Press and hold LAP buttons for 2 seconds to go out LAP mode and return to
normal mode.
WHEEL CIRCUMFERENCE TABLE
1. The details below have been calculated using following formula: Tire
Diameter (inches) x 25.4(mm/inches) x 3.1416 = wheel circumference
(in mm).
2. Identify the tire size of your ATV/Motorcycle when you need to change
different tire size and key in the corresponding number shown in the
following chart.
Circumference
Circumference
Circumference
Tire Size
Tire Size
Tire Size
number
number
(mm)
(mm)
15 inch
1197
19 inch
1516
23 inch
16 inch
1277
20 inch
1596
24 inch
17 inch
1357
21 inch
1676
25 inch
18 inch
1436
22 inch
1756
26 inch
3. These values are approximate and will differ for different brands of
tyre, we would always recommend that you measure the distance
travelled per revolution of the wheel in mm and enter this into the
computer.
4. The computer calculates the wheel rotating length between 2 passes
of the magnet; use this table to find the settings when you are using a
reed sensor or an universal hall sensor with magnet to measure your
speed.
5. If you are using a cable drive speed sensor then enter the number of
turns of the cable perf the wheel into the pulses screen.
6. You can use more magnets, enter the number of magnets fitted into
the pulses screen.
7. If using a sprocket tooth counter speed sensor or internal pulse
gearbox speed sensor enter the number of pulses per wheel
revolution into the pulses screen.
Clock, RPM, Wheel, Divider, Unit, Maintain, Thermometer, fuel meter and ODO SET UP
1. Setup operations include 12/24hour clock, bar rpm scale, shift warning
RPM, numbers of engine rotation per signal, wheel circumference, signal
divider, units, maintain reminder, units of temperature,
temperature
warning, fuel meter input resistance selection and odometer adjustment.
These must be set up step by step. The computer will be automatically
revert to normal mode if no button is pressed for 75 seconds at any
setting screen.
2. Press both MODE & RESET buttons to go into setting mode. In setting
mode, each press of the RESET button increments the flashing digit by 1
or converts units. Press MODE button to confirm the digit setting and
jump to next digit or next setting screen to be set. Press MODE button for
2 seconds at any setting screen to finish the setting and go to normal mode.
3. It displays "12 or 24H and XX:XX:XX " symbols and AM/PM when you
select 12H. Operate buttons as described in item 2 to finish clock
setting and jump to shift RPM warning setting.
4. It displays the default "RPM r06500", the digit "0" flashes. Follow the
item 2 of button operation to finish the shift RPM warning setting and
jump to engine specification setting.
5. It displays "RPM SP 1r1P", the default value is 1r1P; there are 6 options:
1r1P, 1r2P, 1r3P, 1r4P, 2r1P, 3r1P,. "r" means the numbers of
enginerotation, "P" means number of signals from engine. For example
the value 2r1P means the engine rotates 2 turns to output one signal.
6. Press RESET button to move in loop sequence from one to another
value of the 6 values. Press MODE button to confirm the setting and go
to speed sensor type screen.
7. It displays SPD SEn HALL or SPD SEn rEEd, HALL type is for Acewell's
unique 2 wires hall sensors only, rEEd type is for reed sensors, gear
sensors and signals from ECU. A gear sensor has 3 wires and must be
powered from the bike. Follow item 2 of button operation to confirm
the sensor type and jump to wheel circumference setting screen.
8. In "SPD cXXXX" display, "c" means "Circumference", following 4 default
digits; flashing digit is digit to be set. Follow the item 2 of button
operation to finish the wheel circumference setting and jump to signal
divider setting.
9. It displays "SPD P-001", the pulses screen, the number of pulses into the
computer per turn of the wheel. Follow item 2 of button operation to
finish the setting and jump to unit setting.
10. It displays KM/H or MPH, each press of RESET button converts unit;
press MODE button to confirm unit setting and jump to decimal point
setting.
11. It displays "99.9Km/H SPD & on" or "99Km/H SPD & oFF", the decimal
point will disappear when Off is selected. Follow the item 2 of button
operation to finish the decimal setting and jump to maintain reminder
setting.
12. It displays
and TRIP, RT or oFF, TRIP is 1000km (621Miles) and RT is
100 hours by default. Follow the item 2 of button operation to finish
the maintenance reminder setting and jump to voltage warning setting.
The maintenance reminder function will be not be shown when "OFF"
is selected.
13. It displays "
b-on and a flashing numbers of voltage" to be set, "b-on"
means battery warning on voltage – when the voltage falls below this
number
the LED will flash, setting range from 11.0 to 15.0V. It displays "
(mm)
b-off and a flashing numbers of voltage", "b-off" means battery
1835
warning off voltage, setting range from 11.0 to 15.0V to, but
voltage must larger than b-on voltage – when this voltage is exceeded
1915
the LED will go off. It displays "
b-HI and a flashing numbers of voltage"
1995
to be set, "b-HI" means battery warning on voltage – when the voltage
2075
is exceeded the LED will come on, setting range from 11.0 to 15.0V".
Follow the item 2 of button operation to finish the voltage warning
setting and jump to thermometer 1 setting.
14. It displays " 1
,
or oFF", each press of RESET button converts ,
°C
°F
Off, the temperature bars will disappear when you select oFF mode;
press MODE button to confirm temperature setting and jump to
temperature 1 warning setting.
15. It displays " 1 XXX" and the selected unit. Follow the item 2 of button
operation to finish the temperature warning setting and go to
thermometer 2 setting.
16. thermometer 2 setting It displays "** 2
RESET button converts
°C
,
°F
or Off, press MODE button to confirm
temperature setting and jump to scan setting.
17. It displays SCAn and on or oFF, It displays "flash 01 & SCAn" if you
select Scan on, it means the time in seconds to display each function,
for example 05 means every 5 seconds auto change to the next
function, the set range is 01-20. Follow the item 2 of button operation
to finish the SCAN setting and go to fuel sensor resistance setting.
18. It displays "on, off or rES" and
, it displays fuel tank and full bars as
well flash XXXXr, it means full tank resistance setting, the setting range
of "on" from 10r to 1000r. It displays fuel tank and one bar as well as
flash XXXXr, it means empty fuel sensor resistance setting. Follow the
item 2 to select a resistance same as your fuel sender and jump to
sensor type of **LAP timer setting. The fuel meter bar will disappear if
you select oFF mode. In "rES" mode connecting the input wire to 0v
can bring on the fuel symbol and/or LED indicator instantly.
19. It displays Ir, EF1, EF2 or EF3, Ir means you elect IR receiver as the
sensor for LAP timer, and the selection of EF1, 2 or 3 is a magnetic
field sensor for LAP timer, the number of 1, 2 or 3 is means the
number of magnetic sensor in track, for example EF2 means the track
has 2 magnetic sensor and it will combine 2 sensing signals in one.
Follow the item 2 to set sensor type of LAP timer and jump to freezing
time setting.
20. **It displays flashing 01 and SEC, the range is from 01 to 20 seconds,
the freezing time setting will ignore signals received by the unit within
the set freezing time after it received a signal. Follow the item 2 to set
freezing time and jump to odometer setting.
21. It displays "ODO & 00000X km", the "X" is from odometer testing in
factory, follow item 2 to set a desired odometer value and jump to
clock setting or return to Normal Mode. This setting screen will
disappear when the odometer is over 30km (18.6Miles) or your setting
is over 30km
RESET
+
Mode
2 sec.
Mode
2 sec.
b-off
or
°C
°F
,
or oFF", each press of
°C
°F
Mode
Mode
Mode
Mode
Mode
**
Mode
Mode
**
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
Mode
**
Mode
Mode
Mode
Mode
Mode
Advertisement
