Focus ABH-50L User Manual

Quad Photoelectric Beam Detector User Manual
Thanks for purchasing quad photoelectric beam detector, please read the user manual carefully
before installation.
Do not use the product for purposes other than the detection of moving objects such as people and
vehicles. Do not use the product to activate a shutter, etc.which may cause an accident.
Do not touch the unit base or power terminals of the product with a wet hand ( do not touch when the
product is wet with rain etc.) It may cause electric shock.
Never attempt to disassemble or repair the product. It may cause fire or damage to the devices.
WARNING
Do not exceed the voltage or current rating specified for any of the terminals during installation,
doing so may cause damage to the devices.
Do not pour water over the product with a bucket, hose, etc. The water may enter which may cause
damage to the devices.
Clean and check the product periodically for safe use. If any problem is found, do not attempt to use
CAUTION
the product as it is and have the product repaired by a professional engineer or electrician.
1. Features
Interruption time adjustable
NO / NC relay outputs
Integrated tamper switch, turns on when cover is moved.
Frequencies selectable for long distance and stacking installation
LED display signal grade for easy alignment
Wide voltage and energy-saving design
"And" "Or" technology
Digital communication function
FRESNEL lens
IP65 Waterproof grade: IP65
Alignment angle horizontally ±90°, vertically ±10°
Digital filtering, high environment adaptability to eliminate false alarms
Anti-beam interference, workable in harsh situations.
2.Part Description
U Bracket
Mounting Plate Holes
Cover Lock Nut
Lock Screw Front Cover
◆
Front Cover
4. Setting method
1.Wall mounting
4-φ4.5
1.Loosen the screw and remove the cove 2. Attach the installation paper to the wall,mark
the holes first and then make the guide holes.
4*60mm
4.Drop into the four holes with the 5.Connecting wires to the terminals
expansion pipes,fix them with screws.
(please refer to "beam alignment")
2.Pole mounting
Bracket diameter
1. Break out the wire hole and pull out 2. Remove the cover
the wires.
U type bracket
4*60mm
4.Fix the body on the bracket
Wire Hole
Up-bracket
plate
Horizontal adjust
scale
Fresnel Lens
Terminals
Vertical adjust scale
Vertical Alignment
Screw
Horizontal Alignment
Bolster
◆
◆
Body
Base
Wiring Knockout
3.Wiring hole: Remove the foam plug,pull
wire through.and reset the foam plug.
6.Review and reset the cover
Wiring Knockout
Wiring Pressing
3. Drop into the holes with the expansion
pipe,fix it with screws
5. Back to back installation diagram,others
please refer to the step 5 and 6 of the wall
mounting method.
3. Installation notes
1.Please avoid below situations to assure performance
1.Do not install on the unsteady
2.Do not install the unit where objects
or not soiled surface can block the beams like the plants
and laundry can be moved by wind.
4.Avoid any other detector interference
(stack installation only for same model)
2.Normal installation
Model
Detection distance
ABH-50L
ABH-100L
ABH-150L
ABH-200L
ABH-250L/P
Mounting height
Adjusting Angle
Notice: For best testing results,
please avoid testing in 45°
Horizontal 180°（±90°）
5. Connectors
when installation , don't connect the port with the voltage or current which is
Warning
over the normal specification!
Transmitter
1 2 3 4 5 6 7 8
POWER TAMPER
DC10v-24v/AC9v-18v
20mA max
Receiver
2 3 4 5 6 7 8
1
COM NO NC
POWER TAMPER
DC10v-24v/AC9v-18v ALARM
70mA max
6.Connecting wires
1.Single connect: Control panel operating
voltage DC12V. NC alarm output.
Connecting to power supply parallel
Alarm input
Control panel
2 2 3 4
1 1
11 11
Transmitter Receiver
3.Prevent direct sunlight or fluorescent
object entering into internal receiver.
5.Avoid aerial wiring
Detection Distance Beam Angle
50m 1.6m
100m 2.0m
150m 2.6m
200m 3.4m
250m 4.4m
Beam spread range
Beam spread range
Detection Distance
Vertical 20° (±10°）
Notes:
1 . Power voltage input: DC10v-24v/AC9v-18v
2 . No heater in the package, please order if required.
3 . The tamper switch is independent of other circuit;
it would open if the cover was removed
Notes:
1 . Power voltage input: DC10v-24v/AC9v-18v
2 . No heater in the package, please order if required.
3 . The tamper switch is independent of other circuit;
it would open if the cover was removed.
4 . Relay connection point 1C 24VDC 0.5Amax
2.Stacked connect. Control panel operating
voltage DC12V.NC alarm output series
connect
1 2 1 2 3 4
Control panel
11
11
1 2 3 4 1 2
13 13
Transmitter Receiver
.
.
Alarm input