Hakko Electronics FA-430 Instruction Manual

(!)HAK.«o
t!4!S�FA-43D
FUME EXTRACTION
Instruction Manual
Thank you for purchasing the HAKK.O FA-430 Fume Extractor.
Please read this manual before operating the HAKKO FA-430.
READ AND SAVE THESE INSTRUCTIONS.
Keep this manual readily accessible for reference.
1. PACKING LIST AND PART NAMES
HAKKO FA-430 Fume extraction system ............... 1 Main flltar {Inside main unit) .................................. 1
Power cord ............................................................ 1 Pre-filter (Inside main fllter) .................................... 1
Cap {Inside main unit) ........................................... .1 Instruction manual ................................................ 1
Cap
8
Duct set (Duct Adaptar Rectangular nozzle or
3 inch adapter
Round nozzle Nat) ,.,..... -
I I
Duct
_.,./ )
I
�
/
./
(� � Adapter
or
Rectangular nozzle
Round nozzle
2. SPECIFICATIONS
HAKKO FA-430
e
Power Consumption 120W
Absorption Capacity •t High Medium Low
4.7rn3hnin 3.7m•/min 2.8m /min
I I
Collection Efficiency •2 98%
3
Duct diameter cj,55 mm (2.2 in.)
Dimensions 330(W) x 366{H) x 343(0) mm (t 3xt 4.4x13.5 In.)
Waight (w/o cord) 7.5 kg (t6.5 lb.)
•1 Whan using 2 ducts
•2 It is an initial value of collection efficiency based on counting method for airborne dust collected
by a single plate of filler (unfolded).
• Electrostatic Protection
This product includes such features as electrically conductive plastic parts and grounding of Iha unit
as measures to protect the device to be soldered from Iha effects of static alactrlclty. Be sure to observe
the following instructions:
1. The plastic parts are not insulators, they are conductors. When making repairs or replacing
parts, take sufficient care not lo expose live elaclrical parts or damage insulation malarial&.
2. Ba sure to ground the unit during use.
99 Washington Street
Melrose, MA 02176
Phone 781-665-1400
Toll Free 1-800-517-8431
Visit us at www.TestEquipmentDepot.com
3.WARNINGS, CAUTIONS, NOTES AND EXAMPLES
Wamlnga, cautions and notes are placed at crHlcal point• In this manual
attention to significant llama. They are defined
WARNING: Failure
&
CAUTION : Failure
&
NOTE : A NOTE indicates
This unit is approved for use as a non-flammable fume extraction system. Misuse of this product
may 1'88UH In damage to the unit or Injury.
• Do not 1blort, combuatlble, �pl0&lve or corrosive gu.
• Store the fume extraction unil in a dry place.
• Do not block Iha exhaust van! of Illa fume extracllon unit.
• Use only genuine HAKKO replacement
• Turn Iha pow.- off whan nOI in 1119, or 1811 unattandld.
Please check to make sure that all items
• Turn Iha pow.- off when changing parts, replacing flHera or storing the HAKKO FA-430.
listBd below are included in the package.
• This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning use of the
appliance in safe way and understand the hazards involved.
•Children shall not play with the appliance.
• Cleaning and user maintenance shall not be made by children
without supervision.
• Do nOI operate the
• Hold Iha plug when Inserting or removing the cord lnllrom the outlll
• Do nOl allow Iha HAKKO FA-4311 to become wet, or UN it with wet hands.
• While ualng the HAKKO FA-430, don't do anything which may cauee bodlly hllffll or phyllCIII damage.
"When using the 3 inch duct,
set the 3 inch adapter
to the main unit.
4. OPERATION
TO REDUCE THE RISK OF FIRE, ELECTRIC SH OCK, OR INJURY TO PERSONS, OBSERVE
THE FOLLOWING:
• Use this unit only In the mannar lntendad by Iha manufacturar.
• For general ventilating usa only. Do not use to exhaust hazardous or explosive materials
and vapors.
"Specifications and design
are subject to change without
notice.
• Attach the duct
ta attach duct
A. How
1. Refer to Figure 1 (right), and attach the
nozzle and adapter
Insert the nozzle and adapter until it stops,
tum the nozzle clockwise. Malce sure Iha
nozzle and adapter are firmly attached.
&CAUTION
lwlat the nozzle tight enough to avoid
coming off.
2. Fit the net on the nozzle. (Figure.2)
3. Insert the duct Into the open port.
If using one duct, ensure the cap is in place
on the unused port.
Whan using two ducts, please store the cap
inside lhe main unit next to the main filter as
shown in Figure 3 (right).
direct the operator'•
follows:
to
u
comply with a WARNING may result in serious injury or death.
comply with a CAUTION may result in injury to Iha operator, or damage
to
to Iha items involved.
to
procedure or point that is important to the process being described.
a
ih
WARNING
parts.
&CAUTION
extrac:llon without the nner; oth-lse It cause the unn to mllfllnc:llon.
fume may
&WARNING
(Fig.1)
Be sure the duct is
sat
facing in the
proper direction
the duct.
during assembly.
to
" ? .--
CD Insert the nozzle
� 12) Tum
nozde clockwise.
the
M�
(Fig.3)
4. OPERATION
attach bench hood.
B. How ta tap
Whan using a bench top hood,
the following parts are required:
93 inch adapter
e3 inchduct
eDuctciamp
"1he standard duct tor the HAKKO FA-430
can not be ulled to connect a bench top hood.
3 Inch
adapter
• Fume extraction unit
1. Connect the power cord to the power
receptacle on the right of the unit.
2. Plug the power cord into a ground wall socket.
3. Tum the power switch on. Power lamp will light up.
&CAUTION
Closa the cover before turning the power
awltch on.
4. Adjust the flow suitable for working environment
by using flow selection switch.
5. Adjust the angle of the duct and nozzle as needed
for optimal performance.
&CAUTION
Flltar Ille reset
• Do not block the open port on purpasa.
• Whan the fan la running, do not open Iha
upper cover.
• Turn the p- off when not In use. Fallura
to do ao may 1'88Ult In shorter niter llfe..
• If It paaaN more than 2000 hours or one
year since the HAKKO FA-430 Is uead,
replace the main niter with n- one at once.
If uelng the main Hiter over replacement
timing, doing so may 1'88uH In damage to
the main unH.
• How to set the filter
"1118 pre-filter and the main filter are pre-installed the unit
(without plastlc for your Immediate use when dellvered.
in
bags)
1. Open the upper cover.
2. Put Iha main filter on the main unit. Sat Iha
finer with the arrow polndng down
(as shown in the illustralion).
3. Flt the pra-fllter on top of the main fllter.
&CAUTION
Be sure the pre-fllter Ilea flat and completely
the top of the m•ln ftltar with no g11ps.
covers
4. Close the upper cover.
Duct clamp
3 inch
•
duct
Power switch
Flow selection
switch
Exhaust vent