Standers 1100 Assembly Instructions

Security Pole
Assembly Instructions:
Use hole "A"
with 8ft
ceiling
Use hole "B"
with 9ft
ceiling
Do not remove
Curve Grab Bar
from main pole
FIGURE 1
NOTE: The Security Pole is designed to be used with
ceiling heights of 7, 8, and 9 feet. If you have a 10 foot
ceiling, you can purchase a 10 foot extension (ITEM-11)
Call 1-800-506-9901 for your nearest dealer.
Determine where you plan to use this product and the
height of the ceiling before continuing the assembly
process.
1. Take all parts out of the box and lay them on a flat
surface as shown in Figure 1. As noted above, ITEM-11
is NOT included but represents an extension for a 10
foot ceiling.
2. If you have an 8 or 9 foot ceiling skip to step 3. If you
have a 7 foot ceiling, attach the Upper Frame (ITEM-1)
directly to ITEM-3 by aligning the holes in ITEM-1 and
ITEM-3 and inserting the Clevis Pin (ITEM-6) through
the holes. After the Clevis Pin is inserted, place the
Cotter Pin (ITEM-7) through the hole of the Clevis Pin
and bend the end of the Cotter Pin to secure the Clevis
Pin as shown in Figure 2.
3. If you have an 8 foot or 9 foot ceiling, attach the Upper
Frame (ITEM-1) to the Extension Tube (ITEM-2) by
aligning the holes in the large diameter tube of ITEM-2
with the set of holes in (ITEM-1) and inserting the Clevis
Pin and Cotter Pin as previously done in Step 2 and
shown in Figure 2.
4. The Extension Tube (ITEM-2) has 2 sets of holes
marked "A" and "B" in Figure 1. The set of holes marked
"A" are for an 8 foot ceiling. The set of holes marked "B"
are for a 9 foot ceiling.
5. Attach the Extension Tube (ITEM-2) to (ITEM-3) by
aligning the appropriate ceiling height set of holes,
marked "A" or "B" of (ITEM-2) with the mating holes in
the Upper Tube (ITEM-3) and inserting the Clevis Pin
"11" Optional
and Cotter Pin as previously done in Step 2.
purchase for
10ft ceiling
6. Attach ITEM-5 (Base) to ITEM-4 (Main Pole & Curve Grab
Bar), as shown in Figure 1, by aligning the holes in ITEM-4
and ITEM-5 and inserting the Clevis Pin and Cotter Pin as
previously done in Step 2, and as shown in Figure 3.
NOTE: Before Step #7 make sure the Adjustment Nut
(ITEM-8) and the Washer (ITEM-9) are in place on
threaded part of bar as shown in Figure 1.
Adjustment Nut (ITEM-8) should be above the Washer
(ITEM-9).
7. Insert the threaded portion of ITEM-3 into ITEM-4 and
place the Safety Pole in the desired location with ITEM-5
on the floor and ITEM-1 on the ceiling.
8. Secure the Safety Pole between the floor and the ceiling,
the Adjustment Nut (ITEM-8) must be tightened in a
clockwise direction with the included wrench (Item not
shown). Tighten the lower Adjustment Nut until the Safety
Pole is secured between the floor and the ceiling.
NOTES:
If the Safety Pole does not appear to be securely fastened
between the floor and ceiling, loosen the Adjustment Nut
(ITEM-8) and make sure the length of the Safety Pole is
perpendicular to the floor and ceiling before tightening the
Adjustment Nut (ITEM-8) again as previously done in Step
7. If assembled correctly, tightening between the floor and
ceiling with the included wrench will provide adequate
stability. It is not necessary, but, if preferred, two Wood
Screws (ITEM-10) can be installed into the ceiling joists as
shown in Figure 4.
Slight movement of the pivoting handle is normal and safe.
This movement allows the locking pin to easily lock into 8
user friendly positions. Pull the pin and rotate the curved
handle. Release the handle and continue to rotate the
curved handle until the spring loaded pin locks the handle
into the desired position.
6
FIGURE 2
FIGURE 3
7
7
6
The