Summary of Contents for Ashford ASH-CH84
- Page 1 C o n g r a t u l a t i o n s o n t h e p u r c h a s e o f y o u r ……. ASHFORD 4 DRW CHEST W E L C O M E T O T H E A S H – CH84 …….
-
Page 2: Year Guarantee
The Ashford Collection is a Modern and Stylish Collection, designed in response to latest interior trends, both in New Zealand and overseas. Finished in a latest European trending Concise Walnut woodgrain, The Ashford Collection is right up with the minute. -
Page 3: Parts List
ASHFORD – ASH-CH84 PARTS LIST Please check you have all the necessary parts before beginning to assembling your cabinet. The measurements provided will help you to identify each part. If any parts are missing or damaged please contact the manufacturers directly, either via our website or our 0800 number. Do not call the store you bought the cabinet from as they will be unable to help you. -
Page 4: Hardware List
ASHFORD – ASH-CH84 HARDWARE LIST CABINET HARDWARE PART ASSEMBLY CODE PICTURE MANYFACTURERS CODE Connecting Bolts 102649 15mm Cams 10251 1 12mm Cams 102510 Drawer Slide Screws 102652 Large Dowels 102515 Screws 102645 Panhead Screws 106 1 18 Bar Handles 106005... - Page 5 ASHFORD – ASH-CH84 CAM INSTALLATION & OPERATION GUIDE The Cam and Connecting Bolt system is used to put your unit together. Below is an explanation of how this system works. To see a demonstration click on the assembly assistance tab at www.warehousefurniture .co.nz DRAWER SLIDES GUIDE Your pack will contain 4 sets of Metal Drawer Slides.
-
Page 6: Install The Hardware
ASHFORD – ASH-CH84 INSTALL THE HARDWARE STEP 1 - TOP Lay the Top of the unit finished side down on a clean, clear surface. Screw four H1 Connecting Bolts into the holes as indicated in the drawing below STEP 2 –... - Page 7 ASHFORD – ASH-CH84 STEP 3 – LH END Lay the LH End on a smooth clean surface with holes facing upwards. Attach three LH Drawer Slides (CL) to the LH End using the H4 Drawer Slide Screws. Use the holes as indicated in the diagram below - each slide requires two screws.
- Page 8 ASHFORD – ASH-CH84 STEP 4 – RH END Lay the RH End on a smooth clean surface with holes facing upwards. Attach two RH Drawer Slides (CR) to the RH End using the H4 Drawer Slide Screws. Use the holes as indicated in the diagram below - each slide requires two screws.
-
Page 9: Assemble The Unit
ASHFORD – ASH-CH84 ASSEMBLE THE UNIT STEP 5 – ATTACH CORNER LEGS TO ENDS Take the LH End. Screw an H9 Screw into each of the pre-drilled holes at the front of the LH end, until the tip of the screw is just coming through the outside of the End. - Page 10 ASHFORD – ASH-CH84 STEP 6 - RAILS Attach the four Rails to the LH End by fitting the H2 Cams installed in the Rails to H1 Connecting Bolts installed in the End as shown below. Ensure that the Front Rail, (one finished edge) has the finished edge facing the same way as the finished edge of the End.
- Page 11 ASHFORD – ASH-CH84 STEP 8 - Carefully turn the unit upright. Attach the Top to the Ends by fitting the H1 Connecting Bolts installed in the Top to the H2 15mm Cams installed in the Ends. Turn the Metal Cams in a clockwise direction to lock the Top to the Ends. Ensure they turn a least a ¼ to ½ a turn...
- Page 12 ASHFORD – ASH-CH84 STEP 10 – Nail on Glides Tap the 4 x H37 Nail on Glides into place on the bottoms of the Corner Legs. These should be positioned as close to the centre of the leg end as possible. Ensure that you place these on the bottom end of the leg – that is, the end that extends further than the bottom of the End.
- Page 13 ASHFORD – ASH-CH84 ASSEMBLE THE DRAWERS Your Ashford 4 Drawer Chest has four drawers. All Drawers are constructed from the same parts and are therefore assembled the same way. Drawer Bottom LH Drawer Side Drawer Back RH Drawer Side To see a demonstration of how to...
- Page 14 ASHFORD – ASH-CH84 STEP 12 - ASSEMBLE THE SMALL DRAWERS Lay the Drawer Front face down on a smooth, clean surface. Attach the LH and RH Drawer Sides by fitting them into place over the Connecting Bolts installed in the Drawer Front.
- Page 15 ASHFORD – ASH-CH84 STEP 13 - ATTACH THE DRAWER SLIDES Turn the drawer upside-down as shown and attach the Drawer Slides (DR and DL) with the four H6 Small Woodscrews as shown below. Ensure that the ends of the slides without the wheels are hard up against the back of the drawer front as shown.