Table of Contents
Advertisement
Sonic Belt Tension Meter
Thank you for purchasing our Gates Unitta Asia Company's
This manual describes operation procedure of U-507.
Contents
Sonic Belt Tension Meter U-507.
Please read this manual thoroughly before
use in order to make full use of functions.
P １
P ３
P ４
P ５
timing belt made by Gates Unitta Asia
P ７
P ８
P ９
P １ ０
P １ 1
P １ ２
P １ ３
Advertisement
Table of Contents
Related Manuals for Gates Unitta Asia U-507
Summary of Contents for Gates Unitta Asia U-507
-
Page 1: Table Of Contents
Sonic Belt Tension Meter Thank you for purchasing our Gates Unitta Asia Company's Sonic Belt Tension Meter U-507. This manual describes operation procedure of U-507. Please read this manual thoroughly before use in order to make full use of functions. -
Page 2: Note On Safety
１.Note on safety Be sure to observe them. ■ Read this "Note on safety" well enough before use in order to use the unit properly. Keep this manual carefully after reading through. ■ Note described here is for preventing danger to user or other people and damage ... - Page 3 When it starts thundering while using this In measuring the tension, always make unit outdoors, turn off power at once and sure that the machine is stopped by turning move to a safe place. off motor power supply or the lik ･...
-
Page 4: Overview, Note, And Checking Item In Defective Measurement
２. Overview, note, and checking item in defective measurement ■ Overview The sonic belt tension meter (U-507) enables non-contact, Sonic wave is generated by flipping the belt span with the simple, and accurate measurement of installation tension belt standing still, and it is captured by the sensor and... -
Page 5: Measurement Principle Of U-507
(unit mass x width) by use of numeric key V riffed belt (3PK) belt ： Span length 102 mm ： Span length 201 mm ： Span length 400 mm 11. Actual tension (N) Fig. 2 U-507 relation between measured value and actual tension... -
Page 6: Explanation Of Each Part Of U-507
４ .Explanation of each part of U-507 Main part Measurement sensor microphone / flexible arm system microphone (standard specification) One-touch connector Cord system microphone (option) LCD screen with backlight "MEASURE" button Power button WIDTH button SPAN button MASS button (unit mass) - Page 7 [Overview of LCD indication pattern] LCD screen ● Displays tension value, etc. Measurement ● Displays tension by three significant digits from 0.01 to 99900. with backlight frequency level ● Displays frequency by three significant digits from 10.0 to 5000 Hz. H : HIGH Memory No.
-
Page 8: Operation Procedure Of U-507 P
５.Operation procedure of U-507 Procedure Description Operation Display screen １ Set up the microphone. Choose an optimum microphone and fix in the main body with one-touch connector. ２ Turn on power. "POWER" button - PUSH No.□ "SELECT" button - PUSH No.□... -
Page 9: Input Procedure Of Data
V-ribbed belt. （Dp−dp） S＝ C − where, Note) Unit mass of U-507, U-505, and U-305 is 10 times the s: Span length (mm) input of conventional type U-303 since the input unit has been C: Distance between axes (mm) changed. -
Page 10: List Of Preinstalled Belt Type Unit Mass
7MPF Polyflex 7M ８.Unit mass list of timing belt made by Gates Unitta Asia ■ Table-2: Unit mass only for U-507/505 and U-305 Data of unit mass can be input by four significant digits, i.e. three digits of integer and one digit below decimal point in g/mm W x m L from 0.1 to 999.9 g/mm W x m L. -
Page 11: Unit Mass List Of V-Belt Made By Gates
９ .Unit mass list of V-belt made by Gates ■ Table-3: Unit mass only for U-507/505 and U-305 V-belt has a rather high rigidity, and difference is generated between the actual tension and measured value which requires correction in the range of standard installation tension. Therefore multiply the mass per meter length of one rib of belt by tension correction factor obtained by calibration by use of the formula below, and employ the resultant value as a WEIGHT value. -
Page 12: １ ０ . List Of Standard Installation Tension Of
１ ０.List of standard installation tension of timing belt made by Gates Unitta Asia 1 Timing belt width 12.7 19.1 25.4 38.1 50.8 63.5 76.2 101.6 127.0 152.4 177.8 203.2 228.6 254.0 (mm) Tooth （25） （31） （37） （50） （75） （100） （150） （200） （250） （300） （400） （500） （600） （700） （800） （900） （1000）... -
Page 13: １ １.List Of U-507 Specification
As for installation tension of our toothed belt, no difference is generated between the measured value of U-507 and actual tension in the measurement range of note 1) - 3) below, and it is not necessary to set any tension correction factor. -
Page 14: １ ２ .Guarantee And After-Sales Service
１ ２ .Guarantee and after-sales service Thanks for purchasing our sonic wave belt tension meter (U-507). This instrument (body) is guaranteed for 1 year (6 months as for sensor), and any failure found during this period attributed to us will be repaired free of charge. - Page 16 HEAD OFFICE 4-26 SAKURAGAWA 4-CHOME,NANIWA-KU OSAKA 556-0022,JAPAN TEL:06-6563-1284 FAX:06-6563-1285 July 15, 2005 2,000 parts .D...