Related Manuals for Rcom MX-BS700R
Summary of Contents for Rcom MX-BS700R
- Page 1 North America Sales & Service www.RcomCo.com Love of life begins with "Rcom" Ver. 1.1 DIGITAL REPTILE BROODER USER'S MANUAL MX-BS700R / MX-BL700R Rcom Reptile Brooder User Manual...
- Page 2 North America Sales & Service www.RcomCo.com Rcom Reptile Brooder User Manual...
-
Page 3: Table Of Contents
Remove the power cord from outlet. Do not touch. Ground Connection for preventing electric shock. Tip : References or useful suggestions in using Rcom product Warning of actions which may be dangerous or cause damage to the incubator. DIGITAL INCUBATOR... -
Page 4: Introduction
▶ If you don't clean the inside of incubator for a long time, dust can cause some trouble or a fire. DIGITAL INCUBATOR Rcom Reptile Brooder User Manual... -
Page 5: Digital Incubator
(Sold seperately) Please use distilled water. nomal water Humidity unit, or dirty water can Air-filter, Temp.& Humi. sensor cause humidity unit Operation part failure. See the description on how to operate the functions. DIGITAL INCUBATOR Rcom Reptile Brooder User Manual... -
Page 6: Digital Incubator
UV lamp ON/OFF Celsius / Fahrenheit Press ON / OFF button Press ON / OFF button at the same time to at the same time to set up outlet time set up UV lamp time DIGITAL INCUBATOR Rcom Reptile Brooder User Manual... -
Page 7: Digital Incubator
Press “-” button to going down the time Keep pressing Temperature Down button until in unit of 1 hour . "H.OFF" comes out. If you press “SET” button to save the setting. DIGITAL INCUBATOR Rcom Reptile Brooder User Manual... -
Page 8: Brooding
Installation Environment Be careful the details below when you use. Rcom Brooder is designed and manufactured to provide convenient use to customers through latest digital control technology. However, the following requirements must be followed, otherwise it may have fatal effects on the animal. The inside environment of the Brooder is largely affected by the installation environment and the equipment is recommended to be installed in a place where there are minimal noise and shock. - Page 9 ▶ After checking float switch, please assemble a filter like the reverse of disassemble. [Fig-2] [ How to UV lamp assemble ] ▶ Put UV lamp into socket on the left, turn left to lock. DIGITAL INCUBATOR Rcom Reptile Brooder User Manual...
- Page 10 ▶ The equipment operates when the power cord is connected to the back of the main body as in [Fig-B] and the power plug is connected to the power outlet . [Fig-B] DIGITAL INCUBATOR Rcom Reptile Brooder User Manual...
-
Page 11: Function Settings
▶ If you unplug the power cord and re-plug while the SET button is pushed, “rSt” will appear on the display unit and the equipment will be initialized to a setting when it was first released from the factory. Power Cord DIGITAL INCUBATOR Rcom Reptile Brooder User Manual... -
Page 12: Function Settings
※ The display unit shows current temperature even when the heating and ventilation functions are stopped. When the ventilation fan is stopped, there might be slight deviation between the displayed temperature and the actual temperature as air is poorly circulated. DIGITAL INCUBATOR Rcom Reptile Brooder User Manual... -
Page 13: Function Settings
If necessary, recorrection is possible, however, it isn’t desirable for users to correct it directly. In case that correction is necessary, please contact Rcom homepage (www.Rcom.co.kr→data center → Instruction manual categoty) or place where you purchased to inquire about it. As low price thermometer and hygrometer easy to purchase in the open market have much deviation of estimate value, it is desirable to use corrected thermometer and hygrometer for exclusive use. -
Page 14: Function Settings
The allowable load is 100W or lower. The use of outlet above the allowable load can cause the failure or fire. Be careful about that. Outlet (indoor) DIGITAL INCUBATOR Rcom Reptile Brooder User Manual... -
Page 15: Function Settings
“S.ON” will appear on the display unit. [Default : ON] OFF : If you push the TEMP+ button again for 5 seconds all sounds are turned off and “S.OFF” will appear on the display unit. ◀ ▶ DIGITAL INCUBATOR Rcom Reptile Brooder User Manual... -
Page 16: How To Clean
Picture ⓓ. At this point do NOT completely remove the silicon hose from the cover, but follow Picture ⓔ which will allow easier assembly (using tools will help). ▶ Brush and wash. DIGITAL INCUBATOR Rcom Reptile Brooder User Manual... -
Page 17: How To Clean
▶ Take out the tray and wipe the inner surface of the sight glass with a soft cloth. Do not clean the incubators with benzene or thinner, it can cause modify or bleach. ▶ Assemble in the reverse order of separation and store. DIGITAL INCUBATOR Rcom Reptile Brooder User Manual... -
Page 18: Product Information
6. Broken or problem caused by ‘Customer’s mistake or fault’ ※ Product Registration Procedures If you are a new member of Rcom, you need to log in our website at www.Rcom.co.kr 1. Click “SIGN UP” on top of the right corner. - Page 19 Rcom Reptile Brooder User Manual...
- Page 20 I t can be changed wi t hout noti c e f o r i m provement i n perf o rmance, desi g n,treatment, and software, etc. RcomCo.com SELLER MANUFACTURER www.RcomCo.com ● OFFICE : 218, Sangdong-ro, Sangdong-myeon, Gimhae-si, Gyeongsangnam-do, 50805 South Korea Rcom is the Best Design with High Quality, Value, and Perf o rmance! Rcom Reptile Brooder User Manual...
Need help?
Do you have a question about the MX-BS700R and is the answer not in the manual?
Questions and answers