Dbs; Cable Box; Dvd•Aux; Dvd Codes - RCA Universal Remote User Manual

The DVD•AUX Button
The DVD•AUX Button allows you to assign another TV, VCR, DBS, Cable Box or
DVD. The DVD•AUX Button is defaulted to RCA/DVD systems. To assign
another device to the DVD•AUX button:
1. Manually turn on the the device
you wish to assign to the
DVD•AUX button (TV, VCR,
Cable Box, DVD or DBS System).
Find the three digit code for the
device you wish to program in
the code list
2. Press and hold the CODE
SEARCH button until the
INDICATOR LIGHT lights, then
release the CODE SEARCH
button.
3. Press and release the DVD•AUX
button. The INDICATOR LIGHT
will blink.
4. Press TV, VCR or DBS•CABLE
for the device you want to
program.
For DVD press VCR.
For DBS press DBS•CABLE.
For Cable Box press DBS•CABLE.
The INDICATOR LIGHT will blink
again then remain lit.
5. Enter the code using the Number
Buttons.
After your code is entered, the
INDICATOR LIGHT will turn off.
6. Aim the remote at your device
and press the ON•OFF button.
Your device should turn off.
Note: If your device does not
respond, try all the codes for your
brand. If the codes do not work,
or your brand is not listed, try the
Code Search method on page 10.
7. With your device on, press CH+.
If the device responds, no further
programming is required.
8. Enter your code here for easy
reference.
DVD Code List
Aiwa ........................................................350
Hitachi ....................................................351
JVC ................................................161, 352
Konka ..............................................353, 354
Magnavox ..............................162, 356, 357
Mitsubishi ................................................163
Panasonic ..............................................355
Philips ....................................162, 356, 357
9
Device Page
TV ..............................4-5
VCR...............................6

DBS ...............................7

Cable Box .....................8

DVD..............................9
CODE
INDICATOR
SEARCH
LIGHT
(BLINK)
DVD•AUX
TV
VCR
DBS•CABLE
(BLINK)
(OFF)
ON OFF
DVD•AUX CODE
TV VCR CABLE DBS
Pioneer ....................................................165
ProScan ..................................................160
RCA ........................................................160
Sanyo ......................................................359
Sony ........................................166, 360, 361
Toshiba....................................167, 362, 363
Zenith ......................................................364

Programming With Code Search

If your TV, VCR, DVD, DBS or Cable Box does not respond after you have
tried all the codes for your brand, or if your brand is not listed, try
searching for your code by following the steps below.
1. Turn on the device you wish
to program.
2. Press and hold CODE SEARCH
until the INDICATOR LIGHT
lights, then release CODE
SEARCH.
3. Press and release the device
button for the device you are
programming (TV, VCR or
DBS•CABLE). The INDICATOR
LIGHT will blink once then
remain lit. DVD codes are
programmed under the VCR
button.
Note: For AUX, press DVD•AUX then
the device button you are
assigning to DVD•AUX.
4. Press and release ON•OFF until
your device turns off.
Important: You may have to
press ON•OFF up to 200 times.
5. When your device turns off,
press the ENTER button, the
INDICATOR LIGHT will go off.

Retrieving Codes

If you need to find the three-digit code for your TV, VCR, DBS, DVD or
Cable Box after your device is set-up using Code Search, use this procedure.
1. Press and hold CODE SEARCH
until the INDICATOR LIGHT
lights, then release CODE
SEARCH.
2. Press and release the device
button for the device's code
you are retrieving (TV, VCR or
DBS•CABLE). The INDICATOR
LIGHT will blink once then
remain lit.
Note: For AUX, press DVD•AUX
then the device button for the
code you are retrieving.
3. Press and release CODE
SEARCH. The INDICATOR
LIGHT will turn off.
4. Starting with 0 on the keypad,
press the number buttons in
DVD
order (0-9) until the
INDICATOR LIGHT blinks.
5. The number which causes the
INDICATOR LIGHT to blink is
the first digit of your code.
6. Repeat step 4 until you have
retrieved all three numbers in
the code.
CODE
INDICATOR
SEARCH
LIGHT
VCR TV
DVD•AUX
DBS•CABLE
(BLINK)
ON OFF
(OFF)
INDICATOR
CODE
LIGHT
SEARCH
TV
VCR
DVD•AUX
DBS•CABLE
(BLINK)
CODE
SEARCH
(OFF)
(BLINK)
...
10