Summary of Contents for CLR Networks CLR-IES-42S
-
Page 1: Ethernet Switch
CLR-IES-42S Unmanagment Industrial Ethernet Switch User manual (First Publish Edition: V3.1... - Page 2 Notice: Before using this manual, please read the following license agreement. Important declaration: The company provided in this manual for any information, does not mean these informations can provide to the third parties. Notice: AS technical developing ， ， ， ， maybe some part of the datasheet get different with actual product.
- Page 3 SAFETY PROVISION FOR THE USING NOTICE This product is designed as a good and reliable quality, however it still need to avoid human hurt or destroy. Please read carefully and keep this manual for search. Do not place the equipment near water or moisture.
-
Page 4: Table Of Contents
Chapter 2 Product Introduction Chapter 3 Hardware construction 3 .1 C L R -IE S -4 2 S E th e rn e t s wi tc h 3.2 CLR-IES-42S Front Panel 3.3 LED indication light 3.5 Power supply input PIN Chapter 4 Hardware installation 4.1 DIN-Rail installation... -
Page 6: Chapter 1 Introduction
Reliable protection for EMC and against over current / over voltage CLR-IES-42S support relay output warning for power failure. Relay can give output alarm in case of power supply failure or interruption of port link to notice or remind site engineers to make quick response for appropriate emergency maintenance. - Page 7 CLR-IES-42S industrial Ethernet Switch 1pcs User manual 1pcs Inspection Report for Industrial Ethernet 1pcs switch - 2 -...
-
Page 8: Chapter 2 Product Introduction
Chapter 2 Product Introduction 2.1 Product parameters Content CLR-IES-42S RJ45 ports 4x 10Base-T/100Base-TX 2 x100Base-FX Optic ports Standard：IEEE 802.3, IEEE 802.3u, IEEE 802.3x、 ：148810pps store-and-forward mode rate System MAC address table size：2K parameter store-and-forward mode Converter method: Broad cast storm Protection... -
Page 9: Chapter 3 Hardware Construction
3.2 CLR-IES-42S Front Panel The CLR-IES-42S is two 100Base-FX and Two 10/100 Base-TX. 3.3 LED Indication lights The front panel of CLR-IES-42S industrial Ethernet switch have LED contains several LED indicator, it can display socket state and easy to find & solve problem. - Page 10 Port have build active network connection Link/Act(Green) Blinking Port active Port do not network connection - 5 -...
-
Page 11: Power Supply Input Pin
3.5 Power supply input PIN Side panel have one port could connect with ground directly. CLR-IES-42S industrial Ethernet switch have standard DC9~36V power supply input. Also could choose DC48V input. When choose these two voltage , the Ethernet switch support dual power input , as spare use . -
Page 12: Chapter 4 Hardware Installation
Chapter 4 Hardware Installation 4.1 DIN-Rail installation That series equipment back panel have fixed well DIN rail-way connection seat. If need installation, please check DIN rail way condition . Main including 2 terms : Checking DIN-Rail is fixed firm, DIN-rail is installed on other equipment, whether there is enough space . -
Page 13: Fiber Connection
Industrial Power supply This series Ethernet switch supply DC9--36V power (or 48V DC power ,220V AC power). After all other cables connected, you can connect the power . 4.3 Fiber connection This series Ethernet switch provide full-duplex 100Base-FXsingle-mode or multimode fiber interface. Optical interface type can be selected according to requirements of SC / ST / FC. -
Page 14: Chapter 5 Testing Guide
Chapter 5 Testing Guide 5.1 Self-examination When the equipment on power , front panel all port indicate light will shine in all, shine in turn once , that mean all ports work normal . 5.2 RJ45 Port Testing As schematics 5-1 shows, when Ethernet switch on power, Choose any two RJ45 ports through directly network link connect with two testing PC network interface. -
Page 15: Fiber Optic Port Test
, and send Ping command each other , make sure two sides not lose package , and the same time corresponding optic port ‘s LINK light shine , that means two optic ports hardware working normal. Below picture is CLR-IES-42S optic port testing picture . - 10 -... -
Page 16: Chapter6 Network And System Allocation
Ethernet/hub with terminal which used as shared internet link. 6.2 System Allocation CLR-IES-42S series Ethernet switch standard power supply is DC9--36V. Users can choose according to the actual situation DC48V or DC110/220V power or AC110V/220V power. - Page 17 - 12 -...
-
Page 18: Chapter 7 Maintain And Service
Chapter 7 Maintain and Service The switch has 5 years’ guarantee.According to the Product Specifications of Maiwe, we will maintain or change the product for free which has any problem in this guarantee,of that is not including the destroy of error usage,accident, natural disaster and uncorrect installation.
Need help?
Do you have a question about the CLR-IES-42S and is the answer not in the manual?
Questions and answers