Guest 2530 Owner's Manual

SINGLE INPUT 120A MAXIMUM BATTERY ISOLATORS
Models Current Rating
2530
IMPORTANT SAFETY INSTRUCTION
This manual contains important safety and wiring instructions for the
isolator. Read the entire manual before using. Also read all instructions
and cautions for the isolator, batteries and equipment in the vicinity of the
batteries.
RISK OF EXPLOSIVE GASES! WORKING IN THE VICINITY OF
LEAD ACID BATTERIES IS DANGEROUS. BATTERIES
GENERATE EXPLOSIVE GASES DURING NORMAL OPERATION.
THEREFORE IT IS OF THE UTMOST IMPORTANCE THAT WHEN
INSTALLING THE ISOLATOR THESE INSTRUCTIONS ARE
FOLLOWED.
Personal Safety Precautions
Adhere to the following personal safety precautions when installing or
working with the isolators:
1. Someone should be within voice range or close enough to
come to your aid when you work near a lead-acid battery.
2. Have plenty of fresh water and soap nearby in case battery
acid contacts skin, clothing, or eyes.
3. Wear complete eye protection and clothing protection.
Avoid touching eyes while working near a battery.
4. If battery acid contacts skin or clothing, wash them
immediately with soap and water. If acid enters the eye,
flood the eye with cold, running water for at least ten
minutes and get medical attention.
5. Never smoke or allow an open flame in the vicinity of the
battery.
6. Do not drop a metal tool onto the battery. It may short-
circuit the battery, spark and may cause an explosion.
7. Remove all personal metal items such as rings, bracelets,
necklaces, and watches when working near a lead-acid
battery. A battery can produce short circuit currents high
enough to weld a ring or the like to metal, causing a severe
burn.
Preparing to Charge Precautions
Before charging a battery, read the following precautions:
1. If the battery or batteries must be removed from the
product, always remove the grounded terminal from the
battery first.
2. Be sure the area around the battery is well ventilated while
the battery is being charged. Gas can be forcefully blown
away using a piece of cardboard or other non-metallic
material as a "hand fan".
3. Clean battery terminals. Be careful to keep corrosion from
coming into contact with eyes.
4. Add distilled water in each cell until battery acid reaches
levels specified by the battery manufacturer, if applicable.
Do not overfill. Check water levels frequently. For a battery
without cell caps, carefully follow the manufacturer's
recharging instructions.
5. Never allow the charger battery connection ring terminals to
touch each other.
6. NEVER charge a frozen battery.
OWNER'S MANUAL
No. of outputs
120A
INTRODUCTION
The Guest Battery Isolators are specifically designed to efficiently utilize the
2
energy produced by the alternator and distribute the power evenly to each
battery.
The isolators are connected between the alternator(s) and the batteries.
The difficulty in connecting the isolators is due to the large variety of
alternator configurations. This manual illustrates the most common wiring
configurations.
When installing a Guest Battery Isolator make sure the proper circuit breaker
and wire sizes are utilized.
The Guest Battery Isolators are designed for alternator systems with
negative ground and batteries of the same voltage level.
INSTALLATION
Choosing the Battery Isolator location
The battery isolator should have at least eight inches of unobstructed area
on all sides of the unit for effective cooling. The case of the battery isolator
will become hot during operation. Because the battery isolator is convection
cooled (airflow over the fins of the heat sink), the battery isolator MUST be
mounted with the fins in the vertical position. Mounting on its back on a
horizontal surface may cause the battery isolator to produce excessive heat,
Do not install the battery isolator on carpeted, upholstered, or varnished
surfaces.
Mounting the Battery Isolator
1. Use corrosion resistant #10 sized screws or bolts, backed by a flat
washer, and secured to the mounting surface with a split-ring lock
washer.
2. Hold the isolator to the mounting surface and mark the holes.
3. Remove the isolator and drill the mounting holes.
4. Allign the isolator and assemble the mounting hardware secure.
Wire Size
Current
Rating
50 Amps
70 Amps
100 Amps
120Amps
Typical Wiring Configuration
Diagram 1 – Standard Alternator to Battery Isolator Configuration
+
Alternator
120A Max
R
Recommended Wire Size
0 – 15ft 15 – 20ft 20 – 25ft
10AWG 10AWG
8AWG 8AWG
8AWG 6AWG
4AWG 4AWG
25 – 30ft
8AWG 8AWG
6AWG 6AWG
6AWG 4AWG
2AWG 2AWG
Main
Battery
Auxiliary
Battery