Panasonic WV-CP240EX Operating Instructions

Color CCTV Camera
Operating Instructions
WV-CP240EX
Model Nos.
WV-CP242EX
WV-CP244EX
(Lens Option)
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
Ns1005-0 3TR004221AAA
Caution:
Before attempting to operate this product, please
CAUTION
read the label on the surface of the unit.
RISK OF ELECTRIC
SHOCK DO NOT OPEN
This Class A digital apparatus complies with
Canadian ICES-003.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING
NOTE: This equipment has been tested and found
TO QUALIFIED SERVICE PERSONNEL.
to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference when the
The lightning flash with arrowhead
equipment is operated in a commercial environ-
symbol, within an equilateral trian-
ment. This equipment generates, uses, and can
gle, is intended to alert the user to
radiate radio frequency energy and, if not installed
the presence of uninsulated "dan-
and used in accordance with the instruction manu-
gerous voltage" within the product's
al, may cause harmful interference to radio com-
enclosure that may be of sufficient munications.
magnitude to constitute a risk of
Operation of this equipment in a residential area is
SA 1965
electric shock to persons. likely to cause harmful interference in which case
the user will be required to correct the interference
at his own expense.
The exclamation point within an
FCC Caution: To assure continued compliance,
equilateral triangle is intended to
(example - use only shielded interface cables when
alert the user to the presence of
connecting to computer or peripheral devices). Any
important operating and mainte-
changes or modifications not expressly approved
nance (servicing) instructions in the
by the party responsible for compliance could void
literature accompanying the appli-
the user's authority to operate this equipment.
ance.
SA 1966
Power disconnection. Unit with or
The serial number of this product may be found on
without ON-OFF switches have
the surface of the unit.
power supplied to the unit whenever
You should note the serial number of this unit in the
the power cord is inserted into the
space provided and retain this instruction as a per-
power source; however, the unit is
manent record of your purchase to aid identification
operational only when the ON-OFF
in the event of theft.
switch is in the ON position. The
power cord is the main power dis-
Model No.
connect for all units.
Serial No.
WARNING:
• This apparatus must be earthed.
• To prevent fire or electric shock hazard, do not expose this apparatus to rain or moisture.
• The apparatus should not be exposed to dripping or splashing and that no objects filled with liquids, such as vases,
should be placed on the apparatus.
• All work related to the installation of this product should be made by qualified service personnel or system installers.
PREFACE
Panasonic's WV-CP240EX/CP242EX/CP244EX interline transfer CCD image sensor having 768
series digital signal processing color CCD cam-
horizontal pixels (picture elements), and digital
eras introduce a new level of high picture quality signal processing LSI's. This model offers cutting-
and high resolution through the use of a 1/3-inch edge technology for advanced video surveillance.
FEATURES
1. The following functions are built in. 2. Minimum illumination of 1.5 lx {0.15 foot-can-
(1) Auto Light Control (ALC)/Electronic Light dle} at F1.4
Control (ELC)
(2) Automatic Gain Control (AGC) +15 dB 3. Signal-to-noise ratio of 50 dB
and Automatic Tracing White Balance (Equivalent to AGC Off)
(ATW)
(3) Camera synchronization mode selec- 4. Horizontal resolution of 480 TV lines
table between internal (INT), Line-locked
(LL) for WV-CP240EX and WV-CP244EX 5. Auto iris lens control selectable between
and Multiplexed Vertical Drive (VD2). video signal and DC power supply.
PRECAUTIONS
1. Do not attempt to disassemble the camera. 3. Do not expose the camera to rain or
To prevent electric shock, do not remove moisture, or try to operate it in wet areas.
screws or covers. This product is designed for indoor use or
There are no user serviceable parts inside. locations where it is protected from rain and
Ask a qualified service personnel for servic- moisture.
ing. Turn the power off immediately and ask a
qualified service personnel for servicing.
2. Handle the camera with care. Moisture can damage the camera and also
Do not abuse the camera. Avoid striking, create the danger of electric shock.
shaking, etc. The camera could be damaged
by improper handling or storage.
4. Do not use strong or abrasive detergents objects. Otherwise, blooming or smear may
when cleaning the camera body. be caused.
Use a dry cloth to clean the camera when it is
dirty. 7. Do not operate the camera beyond its
In case the dirt is hard to remove, use a mild specified temperature, humidity or power
detergent and wipe gently. Afterwards, wipe source ratings.
off the remained part of the detergent in it Use the camera under conditions where tem-
with a dry cloth. perature is between –10 °C - +50 °C {14 °F -
122 °F}, and humidity is below 90 %.
5. Clean the CCD faceplate with care. The input power source is 120 V AC 60 Hz for
Do not clean the CCD with strong or abrasive WV-CP240EX, 12 V DC for WV-CP242EX, and
detergents. Use lens tissue or a cotton tipped 24 V AC 60 Hz for WV-CP244EX.
applicator and ethanol.
Caution:
6. Never face the camera towards the sun.
To prevent fire or electric shock hazard, use
Do not aim the camera at bright objects.
a UL listed cable (VW-1, style 1007) for the
Whether the camera is in use or not, never
DC 12 V or AC 24 V Input Terminal.
aim it at the sun or other extremely bright
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS
<WV-CP240EX>
Printed in China
ALC BLC ON
ALC BLC ON VIDEO SHARP INT
VIDEO SHARP INT
VIDEO OUT
LL
DC ELC SOFT OFF
<WV-CP244EX> DC SOFT LL
ELC OFF
AC 24V IN
GND
1 2
ALC BLC ON
VIDEO SHARP INT
VIDEO OUT
DC ELC SOFT OFF LL
For U.S.A
ALC BLC ON
<WV-CP242EX>
VIDEO SHARP
DC 12V IN
DC SOFT
OFF
ALC BLC ON ELC
VIDEO SHARP
VIDEO OUT
DC SOFT
ELC OFF
q ALC Lens Connector ON: Select this mode when a strong light
Supplies power and control signals to an auto
iris lens (not supplied). OFF: Normal picture.
w Flange-back Adjusting Ring !1 Detail/Aperture Level Selector [SHARP,
This ring adjusts the back-focal distance or SOFT]
picture focus. Rotate this ring clockwise for a The detail/aperture level can be selected with
this selector. Set it to the desired position
C-mount lens or counterclockwise for a CS-
mount lens. while observing the picture on the monitor.
SHARP: Normal position.
e Lens (option) SOFT: Select this position when a Quad
r Mount Adapter
The camera mounting screw hole is for !2 Automatic Light Control/Electronic Light
mounting the camera onto a mounting brack- Control Selector [ALC, ELC]
Lets you select the mode according to the
et. The camera is originally designed to be
mounted from the bottom, however, a top- lens type used.
mounting type is also available. To mount ALC: Select this mode when an auto iris lens
from the top, remove the mount adapter from
the bottom of the camera by removing two ELC: Select this mode when a fixed iris lens
fixing screws. Attach the mount adapter to
the top as shown in the diagram, then mount
the camera on the mounting bracket. Make
!3 Lens Drive Signal Selector [VIDEO, DC]
sure that two original screws are used when
Lets you select the mode according to the
mounting the mount adapter; longer type
screws may damage inner components, too type of auto iris lens drive signal to be sup-
shorter type screws may cause the camera plied to the lens from the auto iris lens con-
drop. nector.
VIDEO: Select this mode if you are using a
t Focus Fixing Screw
y Power Cord (only for WV-CP240EX) DC: Select this mode if you are using a auto
Connect this power cord to an electrical out-
let of 120 V AC 60 Hz.
!4 Video Output Connector [VIDEO OUT]
u DC 12 V Input Terminal This connector is for connecting with the
[DC 12V IN] (only for WV-CP242EX) VIDEO IN connector of the video monitor.
This terminal is for connecting the 12 V DC Whenever the multiplexed vertical drive (VD2)
signal is supplied to this connector, the cam-
power supply cord.
era synchronization mode is automatically set
i AC 24 V Input Terminal
to Vertical Drive.
[AC 24V IN] (only for WV-CP244EX)
This terminal is for connecting the 24 V AC
60Hz power supply cord.
Cautions:
• Connect to 12 V DC (10.5 V-16 V) or 24 V
o Synchronization Mode Selector
AC (19.5 V-28 V) class 2 power supply
[INT, LL] (only for WV-CP240EX and WV-
only. Make sure to connect the grounding
CP244EX)
lead to the GND terminal when the power
Selects the camera synchronization mode as
is supplied from a 24 V AC power source.
either internal sync mode (INT) or line-lock
• To prevent fire or electric shock hazard,
mode (LL).
use a UL listed cable (VW-1, style 1007)
INT: Sets to internal 2:1 interlace.
for the DC 12 V or AC 24 V Input
LL: Sets to Line-lock mode.
Terminal.
!0 Back Light Compensation Mode Selector
[BLC ON, OFF]
Lets you select the mode according to the
position of the object and light conditions on
the screen.
CONNECTIONS
A. WV-CP240EX (120 V AC 60 Hz)
Connect the power cord to an electrical outlet
of 120 V AC 60 Hz.
B. WV-CP242EX (12 V DC)
Connect the power cord to the DC 12 V IN
terminal on the rear panel of the WV-
CP242EX.
@ !
12 V DC
(10.5 V - 16 V)
Resistance of copper wire [at 20 °C {68 °F}]
Copper wire #24 #22 #20
size (AWG) (0.22 mm 2 ) (0.33 mm 2 ) (0.52 mm
Resistance
LOCK
0.078 0.050 0.03.
Ω/m
Resistance
0.026 0.017 0.010
Ω/ft
• Calculation of maximum cable
between camera and power supply :
10.5 V DC ≤ V − (R x 0.42 x L) ≤ 16 V DC
A
L : Cable length (meters)
R : Resistance of copper wire (Ω/meter)
V : DC output voltage of power supply unit
A
− 12
V
A
L standard = (meters)
0.42 x R
− 16
Mount Adapter V
A
L minimum = (meters)
0.42 x R
− 10.5
V
A
L maximum = (meters)
0.42 x R
C. WV-CP244EX (24 V AC 60 Hz)
Connect the power cable to the AC 24 V IN
terminal on the rear panel of
CP244EX.
AC 24V IN
GND
such as a spotlight is in the background.
1 2
24 V AC, 60 Hz
(19.5 V - 28 V)
Recommended wire gauge sizes for 24 V AC line
System is connected to this camera.
Copper wire #24 #22 #20
size (AWG) (0.22 mm 2 ) (0.33 mm 2 ) (0.52 mm
(m) 95 150 255
Length
of Cable
(Approx.)
(ft) 314 495 842
(ALC lens) is used with this camera.
Caution:
To prevent fire or electric shock hazard,
or manual iris lens is used with this cam-
use a UL listed cable (VW-1, style 1007) for
era.
the DC 12 V or AC 24 V Input Terminal.
Video Cable
1. It is recommended to use a monitor whose
resolution is at least equal to that of the
camera.
auto iris lens that requires a video drive
2. The maximum extensible coaxial cable
signal.
length between the camera and the moni-
tor is shown below.
iris lens that requires a DC drive signal.
Type of RG-59/U RG-6U RG-11/U RG-15/U
coaxial cable (3C-2V) (5C-2V) (7C-2V)
Recommended (m) 250 500 600
maximum
cable length (ft) 825 1 650 1 980
FOCUS OR FLANGE-BACK ADJUSTMENT
The following adjustment should be made by
qualified service personnel or system installers.
q Loosen the focus fixing screw on the side of
the camera.
CS/C switching line
Focusing of
Focusing of
CS-mount lens
C-mount lens
Focus Fixing Screw
Flange-back
Adjusting Ring
SPECIFICATIONS
Mounting the Lens Pick-up Device:
Scanning Area:
Caution:
Before you mount the lens, loosen the screw
Synchronization:
on the side of the camera, and rotate the
flange-back adjusting ring clockwise until it
Scanning System:
stops. If the ring is not at the end, the inner
Scanning:
lens or CCD image sensor may be damaged.
Horizontal:
q Mount the lens by turning it clockwise on the
Vertical:
lens mount of the camera.
Horizontal Resolution:
w Connect the lens cable to the ALC Lens
Video Output:
Connector on the side of the camera.
Signal-to-Noise Ratio:
Electronic Light Control:
Minimum Illumination:
Detail:
Focus Fixing Screw
Lens Mount:
Ambient Operating Temperature:
Ambient Operating Humidity:
q
Power Source and
w
Power Consumption:
#18
2 ) (0.83 mm 2 )
Dimensions (without lens):
0.018
Weights (without lens):
0.006
length
Caution for Mounting the Lens
Weights and dimensions indicated are approximate.
Specifications are subject to change without notice.
The lens mount should be a C-mount or CS-mount
(1"-32UN) and the lens weight should be less than
450 g {0.99 lbs}. If the lens is heavier, both the
lens and camera should be secured by using the
supporter.
STANDARD ACCESSORIES
The protrusion at the rear of the lens should be as
shown in the diagram.
Body Cap............................................................................................1 pc.
Operating Instructions (this document) .............................................1 pc.
Warranty card ....................................................................................1 pc.
the WV-
OPTIONAL ACCESSORIES
C-mount: Less than 13 mm {1/2"}
CS-mount: Less than 8 mm {5/16"}
Lenses: WV-LA2R8C3B, WV-LA4R5C3B, WV-LA9C3B, WV-LF4R5C3A, WV-LF9C3A, WV-LZA61/2S
WV-LZ62/8S
#18
2 ) (0.83 mm 2 )
425
1 403
(10C-2V)
800
2 640
w Turn the flange-back adjusting ring to the Panasonic System Solutions Company,
Unit Company of Panasonic Corporation of North America
desired position.
Security Systems
www.panasonic.com/security
Caution: When the C-mount lens is mounted, For customer support, call 1.877.733.3689
Executive Office: Three Panasonic Way 2H-2, Secaucus, New Jersey 07094
do not rotate the ring counterclockwise
Zone Office
by force after it stops. If the ring is rotat-
Eastern: Three Panasonic Way, Secaucus, New Jersey 07094
Central: 1707 N. Randal Road, Elgin, IL 60123
ed by force, the inner lens or CCD image
Southern: 1225 Northbrook Parkway, Suwanee, GA 30024
sensor may be damaged.
Western: 6550 Katella Ave., Cypress, CA 90630
Panasonic Canada Inc.
e Tighten the focus fixing screw on the side of
5770 Ambler Drive,Mississauga,
Ontario, L4W 2T3 Canada (905)624-5010
the camera.
http://www.panasonic.ca
Panasonic Sales Company
Caution: Tightening the screw by force will
Division of Panasonic Puerto Rico Inc.
cause damage to the screw or deviation
San Gabriel Industrial Park 65th Infantry Ave. KM. 9.5 Carolina
P.R. 00985(809)750-4300
of focus.
© 2005 Matsushita Electric Industrial Co., Ltd. All Rights Reserved.
768 (H) x 494 (V) pixels, Interline Transfer CCD
4.92 (H) x 3.70 (V) mm (Equivalent to scanning area of 1/3"
pick-up tube)
Internal, Line-locked or Multiplexed vertical drive (VD2),
selectable
2 : 1 interlace
525 lines / 60 fields / 30 frames
15.734 kHz
59.94 Hz
480 TV lines
1.0 V[P-P] NTSC composite 75 Ω / BNC connector
50 dB (Equivalent to AGC Off, weight On)
Equivalent to continuous variable shutter speed between 1/60 s
and 1/15 000 s
1.5 lx {0.15 foot-candle} at F1.4
1.1 lx {0.11 foot-candle} at F1.2
SHARP or SOFT, selectable
C-mount or CS-mount, selectable
−10 °C - +50 °C {14 °F - 122 °F}
Less than 90 %
WV-CP240EX: 120 V AC 60 Hz, 3.6 W
WV-CP242EX: 12 V DC, 270 mA
WV-CP244EX: 24 V AC 60 Hz, 3.3 W
67 mm (W) x 65 mm (H) x 123 mm (D)
{2-5/8" (W) x 2-9/16" (H) x 4-13/16" (D)}
WV-CP240EX: 0.48 kg {1.06 lbs}
WV-CP242EX: 0.3 kg {0.66 lbs}
WV-CP244EX: 0.33 kg {0.73 lbs}