Download  Print this page

Advertisement

Service Manual

This Simplified Service Manual is issued to add listed models to the Main Service Manual order No.
MTNC010303C1(CT-20R6E). A set of schematics, unique settings and a complete parts list are included in this
Manual.
Please file and use this Simplified Service Manual together with Main Service Manual, order No. MTNC010303C1 .
"WARNING! This Service Manual is designed for experienced repair technicians only and is not designed for use by the general public.
It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product.
Productspoweredbyelectricityshouldbeservicedorrepairedonlybyexperiencedprofessionaltechnicians.Anyattempttoservice
or repair the product or products dealt with in this Service Manual by anyone else could result in serious injury or death."
The service technician is required to read and follow the "Safety Precautions" and "Important Safety Notice" in this Main Manual.
Color Television
Simplified Manual
(NA7DM)
Panasonic
Model
CT-2017F
Copyright 2002 by Matsushita Electric Corporation of
America. All rights reserved. Unauthorized copying
and distribution is a violation of law.
ORDER NO. MTNC020410A1
B1
Chassis
AP391

Advertisement

   Also See for Panasonic CT-2017F

   Summary of Contents for Panasonic CT-2017F

  • Page 1: Service Manual

    (NA7DM) Panasonic Model Chassis CT-2017F AP391 This Simplified Service Manual is issued to add listed models to the Main Service Manual order No. MTNC010303C1(CT-20R6E). A set of schematics, unique settings and a complete parts list are included in this Manual.
  • Page 2 High Voltage. It should be: ensure that is completely safe to operate. Do not use a 26.60±1.25kV for CT-2017F line isolation transformer when testing. If the upper limit is out of tolerance, immediate service Leakage Current Cold Check and correction is required.
  • Page 3 About lead free solder (PbF) Note: Lead is listed as (Pb) in the periodic table of elements. In the information below, Pb will refer to Lead solder, and PbF will refer to Lead Free Solder. The Lead Free Solder used in our manufacturing process and discussed below is (Sn+Ag+Cu). That is Tin (Sn), Silver (Ag) and (Cu) although other types are available.
  • Page 4: Table Of Contents

    Important Safety Notice ....2 Safety Precautions ....2 About Lead Free Solder (PbF) .
  • Page 5: Service Notes

    Service Notes Note: These components are affixed with glue. Be careful not to break or damage any foil under the component or at the pins of the ICs when removing. Usually applying heat to the component for a short time while twisting with tweezers will break the component loose.
  • Page 6: X-ray Protection Circuit Check

    Service Notes (Continued) IMPORTANT: To protect against possible damage to Procedure: the solid state devices due to arcing or static discharge, 1. Connect receiver to Isolator Transformer. make certain that all ground wires and CTR DAG wire 2. Apply a monoscope pattern. are securely connected.
  • Page 7: Receiver Feature Table

    Table 1. Receiver Features *Note: When ordering a Board, add and ” S” after the Board suffix application. Example, If Order A-Board for CT-2017F, should be ordered as: TNP2AH040S. Specifications are subject to change without notice or obligation. Dimensions and weights are approximate.
  • Page 8: Location Of Controls (receiver)

    Location of Controls (Receiver) Figure 2. Location of Controls (Receiver). POWER VOLUME CHANNEL ACTION TV/VIDEO Remote Control HPJ & A/V Sensor Jacks (Actual appearance may vary) Quick Reference Control Operation Quick Reference Control Operation Power Button - Press to turn ON or OFF. Volume Buttons - Press to adjust Sound Level, or to adjust Audio Menus, Video Menus, and select operating features when menus are displayed Channel Buttons - Press to select programmed channels.
  • Page 9: Disassembly For Service

    Dissasembly for Service Back Cover C-Board - CRT Output Plugs into the socket on the CRT neck. Remove all the screws marked with an arrow( To release the Focus wire, use a flat tool to release from the back of the receiver. the tab in the socket, See Fig.
  • Page 10 Back Cover Disassembly Figure 5. Back Cover Removal • 2 Screws at the top edge • 1 Screw in each lower corner • 1 Screw by the A/V Jacks • 1 Screw by the Flyback Assembly. - 10 -...
  • Page 11: Main Components Location

    Main Components Location (Secured to Cabinet ANODE (HIGH VOLTAGE) by 4 Screws on Corners) Deflection Yoke Convergence Yoke Yoke Wedge Degaussing Coil Speakers Secured by 2 Screws A-Board Tuner C-Board Flyback Dag Ground Main Chassis JACKS CRT Panel Figure 6. Rear View - 11 -...
  • Page 12 Main Components Location (cont...) Q351 GROUND IC001 IC050 RED OUT HALF TONE Socket MPU/VCJ Q352 GREEN OUT Q353 BLUE OUT IC002 EEPROM JK3002 Front A/V Jacks IC003 IC801 IC451 Remote Sensor VCO( ) Vertical Out Q501 H. DRIVE Q551 H.OUT IC551 9V REG IC552...
  • Page 13: Audio Signal Path Block Diagram

    AUDIO SIGNAL PATH BLOCK DIAGRAM Figure 7. Audio Signal Block Diagram - 13 -...
  • Page 14: Video Signal Path Block Diagram

    VIDEO SIGNAL PATH BLOCK DIAGRAM Figure 8. Video Signal Block Diagram - 14 -...
  • Page 15 Notes: - 15 -...
  • Page 16: Parts List

    REPLACEMENT PARTS LIST Model: CT-2017F Important Safety Notice: Components printed in BOLD TYPE have special characteristics important for safety. When replacing any of these components use only manufacturer’s specified parts. REF NO. PART NO. DESCRIPTION REF NO. PART NO. DESCRIPTION...
  • Page 17: Replacement Parts List

    REPLACEMENT PARTS LIST Model: CT-2017F Important Safety Notice: Components printed in BOLD TYPE have special characteristics important for safety. When replacing any of these components use only manufacturer’s specified parts. REF NO. PART NO. DESCRIPTION REF NO. PART NO. DESCRIPTION...
  • Page 18 REPLACEMENT PARTS LIST Model: CT-2017F Important Safety Notice: Components printed in BOLD TYPE have special characteristics important for safety. When replacing any of these components use only manufacturer’s specified parts. REF NO. PART NO. DESCRIPTION REF NO. PART NO. DESCRIPTION...
  • Page 19 REPLACEMENT PARTS LIST Model: CT-2017F Important Safety Notice: Components printed in BOLD TYPE have special characteristics important for safety. When replacing any of these components use only manufacturer’s specified parts. REF NO. PART NO. DESCRIPTION REF NO. PART NO. DESCRIPTION...
  • Page 20 RES,C 390-J-1/4W ASSY, CABINET FRONT 20" R2351 ERJ6GEYJ562V RES,M 5.6K-J-1/10W (Cabinet Front 20”, Guide IR, R2352 ERJ6GEYJ683V RES,M 68K-J-1/10W M009 TXFKY06ESER Badge Panasonic, Label X-Ray R2353 ERJ6GEYJ124V RES,M 120K-J-1/10W Warning) R2354 ERJ6GEYJ123V RES,M 12K-J-1/10W M010 TAS2AA0012 SPEAKER 16-OHM 1.5W R2355 ERJ6GEYJ222V RES,M 2.2K-J-1/10W...
  • Page 21 General Notes DESCRIPTION OF ABBREVIATIONS GUIDE RESISTOR CAPACITOR TYPE TOLERANCE TYPE TOLERANCE Carbon ± 1% Ceramic ± 0.25pF Fuse ± 5% Electrolytic ± 0.5pF Metal Oxide ± 10% Polyester ± 1pF Solid ± 20% Styrol ± 5% Wire Wound ± 2% Tantalum ±...
  • Page 22: Important Safety Notice

    Schematic Notes IMPORTANT SAFETY NOTICE CHIP TRANSISTOR THIS SCHEMATIC DIAGRAM INCORPORATES SPECIAL LEAD DESIGNATION FEATURES THAT ARE IMPORTANT FOR PROTECTION FROM X-RADIATION, FIRE AND ELECTRICAL SHOCK HAZARDS. WHEN SERVICING ESSENTIAL THAT ONLY MANUFACTURERS SPECIFIED PARTS BE USED FOR THE CRITICAL COMPONENTS DESIGNATED WITH A IN THE SCHEMATIC.
  • Page 23: Aviso Importante

    Notas de Esquemáticos NOTA DE SEGURIDAD LOS DIAGRAMAS ELÉCTRICOS INCLUYEN CARACTERÍSTICAS ESPECIALES MUY IMPORTANTES PARA LA PROTECCIÓN IDENTIFICACIÓN DE TERMINALES PARA TRANSISTORES EN CHIP CONTRA RAYOS-X, QUEMADURAS Y DESCARGAS ELÉCTRICAS. CUANDO SE DE SERVICIO ES IMPORTANTE USAR PARA REEMPLAZO DE COMPONENTES CRITICOS, SOLO PARTES ESPECIFICADAS POR EL FABRICANTES.
  • Page 24 A Board - 24 -...
  • Page 25 A Board - 25 -...
  • Page 26 A Board - 26 -...
  • Page 27 A Board - 27 -...
  • Page 28 TNP2AH040DH - 28 - A Board...
  • Page 29: A-board

    A-BOARD - TNP2AH040DH IC001 IC002 IC451 IC2201 ..GND ..GND ..GND ..8.23 ..1.29 ..3.49 .
  • Page 30 A-BOARD - TNP2AH040DH Q001 Q006 Q007 Q008 Q009 0.00 2.75 2.87 2.87 0.58 11.07 0.00 3.40 3.52 3.51 Q050 Q051 Q052 Q053 Q054 4.96 4.96 4.96 0.00 0.00 4.98 4.98 2.76 2.86 2.87 2.78 2.87 Q055 Q090 Q092 Q451 Q452 0.00 1.45 8.92...
  • Page 31: Waveforms

    A-BOARD WAVEFORMS 27.4 Vp-p [5ms] 1.28 Vp-p [20µs] 1.17k Vp-p [20µs] 1.05 Vp-p [20µs (B OUT) IC451 PIN 13 (PUMP UP) Q551 Collector (H OUT) TPA5 (VIDEO) A11-3 14.29MHz X’tal IC001 PIN 35 9.28 Vp-p [5ms] 5.28 Vp-p [20µs] 276.0 Vp-p [5µs] ADC OSC IC801 PIN 1 IC451 PIN 2 (VERT IN)
  • Page 32: C-board

    C Board - 32 -...
  • Page 33 - 33 - C Board...
  • Page 34: A,c-boards

    A-C Boards - 34 -...
  • Page 35 A-Board - 35 - A-C Boards...
  • Page 36 Printed in USA K02042597MR0423...

Comments to this Manuals

Symbols: 0
Latest comments: