Do you have a question about the HC 900 and is the answer not in the manual?
Questions and answers
Summary of Contents for Henny Penny HC 900
Page 1
Henny Penny Heated Holding Cabinet Model HC 900 SERVICE MANUAL...
Page 4
0 TO 3 YEARS: During this time, any frypot that fails due to manufacturing or workmanship issues will be replaced at no charge for parts, labor, or freight. Henny Penny will either install a new frypot at no cost or provide a new or reconditioned replacement fryer at no cost.
Henny Penny Model HC-900 SECTION 1. INTRODUCTION 1-1 HEATED HOLDING The Henny Penny Heated Holding Cabinet is a basic unit CABINET (HC-900) of food processing equipment designed to hold hot foods at proper temperature in commercial food operations. This cabinet will keep hot foods humid while maintaining temperature.
In addition, feel free to contact our corporate headquarters in Eaton, Ohio. Dial 800-417-8405, or 937-456-8405. 1-6 SAFETY The only way to insure safe operation of the Henny Penny Heated Display Cabinet is to fully understand the proper installation, operation, and maintenance procedures. The instructions in this manual have been prepared to aid you in learning the proper procedures.
Henny Penny Model HC-900 2-3 LOCATION The HC-900 should be placed in an area where the doors can be opened without interruption and loading and unloading of product is easy. For proper operation, the cabinet must be level. Do not set anything on top of the cabinet that might close the vent holes.
Henny Penny Model HC-900 3-6 CLEANING PROCEDURES 6. Wipe the control panel with a damp cloth. Do not splash (Cont.) water around the controls. 7. Clean the exterior of the cabinet with a damp cloth. DO NOT use a spray hose to clean the unit. Failure to follow these instructions could cause component damage.
Henny Penny Model HC-900 3-7. OPERATING CONTROLS These instructions are for both 13 and 5 count down timers. 900 and 903 CDT (if applicable) Start-UP 1. Turn the power switch to the ON position. 2. The display shows the increase in temperature, indicating the unit is heating.
Page 22
Henny Penny Model HC-900 3-7. OPERATING CONTROLS Timer Regulation - All timers can be set to a different starting time. 900 and 903 CDT (if applicable) 1. Press and hold the PROGRAM button. (Continued) 2. The control beeps and “Prog Enter Code” shows in display.
Page 23
Henny Penny Model HC-900 3-7. OPERATING CONTROLS Special Program Mode - Consists of Setup Mode and Tech Mode. 900 and 903 CDT (if applicable) Setup Mode (Continued) • Fahrenheit or Celsius • Initialize System - One button programming for times and...
Page 24
The Tech Mode is mostly used at the factory level. The output tests and temperature probe calibration is given below. For further information, call the Technical Services Department at Henny Penny, 800-417-8405, or 937-456-8405. Output Test 1. Press and hold the PROGRAM button for 4 seconds.
Page 25
Henny Penny Model HC-900 3-7. OPERATING CONTROLS Output Test (Continued) 900 and 903 CDT (if applicable) 6. Press the 5 timer button (under “Htr”) to turn heat and heat LED (Continued) on and off. 7. Press the PROGRAM button to move to the next step, or press and hold the PROGRAM button to exit programming.
Henny Penny Model HC-900 The CDT controls have built-in diagnostics which displays 3-8. ERROR CODES error codes on the display. This section describes the codes. (CDT Controls) Displayed Error Code/Warning Problem “E-4” • Displayed if Control Board exceeds 140 F (60 •...
Page 54
0 TO 3 YEARS: During this time, any frypot that fails due to manufacturing or workmanship issues will be replaced at no charge for parts, labor, or freight. Henny Penny will either install a new frypot at no cost or provide a new or reconditioned replacement fryer at no cost.
Page 57
Henny Penny Model HC-900 PARTS LIST HC-900, HC-902, HC-903, HC-906, and HC-908 VENTED CONTROL MODULE 1/3 SIZE AND WIDE BODIED UNITS Item No. Part No. Description Quantity 25944 Rear Panel Studweld Assembly 28155 Cable 25964 Hose - Intake 25963 Hose - Exhaust...
Henny Penny Model HC-900 PARTS LIST HC-900, HC-902, HC-903, HC-906, and HC-908 CONTROL MODULE Item No. Part No. Description Quantity Item No. Part No. Description Quantity 25704 Panel - Access 25717 Label Control Panel 51209 Panel -Access - C E...
Page 60
Nut Hex #10-32 43768 Power Switch - Plastic 27809 Air Duct Assembly - Upper 49038 Decal - Control Panel - HC 900 42964 Air Duct Assembly - Upper - 900K ( SIB ) 49060 Decal -Control Panel-Vented-HC-903 28129 Air Duct Assembly Upper HC-906...
Page 63
For Sales or Service Please Contact The Nearest Henny Penny Distributor General Services Barnett Group PHT Systems Top-Line Distributors 100 Hicks Ave. 2089 York Ave. 1801 Old Highway 8 1501 College Ave. Medford, MA 02155 Memphis, TN 38104 Suite 120...
Page 65
Henny Penny International Distributor Network U.S. Headquarters Brazil Estonia Iceland Henny Penny Corporation Pesin Equipment Food Service Sisustaja As A. Karlsson H. F. Brautarholti 1219 U.S. Route 35 West 09530-260 Tihniku 5 Eaton, OH 45320 USA R. Olavo Bilac 188/198...
Page 66
Lebanon New Zealand Saudi Arabia Taiwan Pro Kitchen Taylor Equipment Limited Commercial Center Development Feco Corporation Cahlfoun Building 4 Ponuz Place & Economy 420, 11 F Keelung Rd. Kaslik - Main Road Mt. Wellington P.O. Box 1210 Sec. 1 Postal Code 110 PO Box 1066 Jounieh Auckland, New Zealand Jeddah 21431, Saudi Arabia...
Need help?
Do you have a question about the HC 900 and is the answer not in the manual?
Questions and answers