7inova 7W230 Quick Installation Manual

Quick Installation Guide

Wireless Ceiling Mount Access Point 300M
Model：7W230
2.5 The login screen below will appear. Enter the "Username" and "Password"
then click "Login" to login. The default Username is "admin" and Password
is "admin".
2.6 After logging in click "Easy Mode" and then click "Network Setting", you
will see 3 modes: AP Mode, Repeater Mode and Client Mode
04
Wireless-N Repeater
Before you start to use this device, please check if there's anything
missing in the package, and contact your dealer of purchase to
claim for missing items:
Package Contents:
1x 7W230 WiFi Repeater
1x 1m Ethernet cable with RJ45 connector
1x Quick Installation Guide
Appearance Introduction
LED indicators' Status Description:
WPS/Reset
Ethernet LED
WLAN LED Power LED
Reset: If need to reset the Repeater, press and hold RESET button for 3-5
seconds, release until all other LED are off except Power LED.
01
Wireless-N Repeater
3 Configuration Mode
3.1 Configure AP Mode
3.1.1 Follow process 2.3 to 2.5.
3.1.2 Select "AP" and enter the information what you want to set up wireless
information and password, then click "Apply", wait for 3~5 seconds it complete.
3.2 Configure Repeater Mode
3.2.1 Follow process 2.3 to 2.5.
3.2.2 Select "Repeater" then click on "Search".
05
Wireless-N Repeater
Indicator Name Status Description
Power Status Indicator Green On Get Powered
Green On Ethernet Connected
Ethernet Status Indicator
LAN
Green fast blink Data Transmission via Ethernet
Green slow blink Wireless Function Launched
Wireless Status Indicator
Green fast blink Data Transmission via wireless
Cautions:
1. Disconnect the device in thunderstorms in case of lightning damage.
2. Keep far from heat source and ensure ventilation.
3. Keep waterproof in the storage, transportation and operating environment.
1 Computer Configuration
1.1 Click "Start→Control Panel→Network and Internet→Network and Sharing
Center→Change adapter settings→Wi-Fi(right click)→Properties"
1.2 Double click "Internet Protocol Version 4(TCP/IPv4)"
1.3 To set up the computer IP 192.168.2.x (x arbitrary integer between 2~252),
subnet mask of 255.255.255.0, Click "OK". Back to the last interface and
click "OK"
02
Wireless-N Repeater
3.2.3 Select wireless which you want to connect and enter the password (if wireless don't
have password is "None"), then enter the wireless information what you want to set.
3.2.4 Then click "Apply" and wait for 3~5 seconds it is complete.
06
Wireless-N Repeater
2 Connect To Wireless Network
2.1 Pulg the Wi-Fi Repeater to a wall socket.
2.2 Click on the network icon( ) on the right
bottom of your desktop. You will find the signal
from the Wi-Fi Repeater. Click on "Connect"
and wait for a few seconds.
2.3 When shows: "Connect to a Network", please click "Connect to the
network without setting it up"
2.4 Open web browser and type http://192.168.2.1 in the browser's address
box. This number is the default IP address for this devices.
Note: Please check whether the WiFi-Repeater accord with factory default
settings once you can't download http://192.168.2.1. If you are still not sure
what reasons, you can reset the WiFi-Repeater, just need to press the reset
button for 3-5 seconds, then try again.
03
Wireless-N Repeater
3.3 Configure Client Mode
3.3.1 Follow process 2.3 to 2.5
3.3.2 Select "Client" then click on "Search"
07
Wireless-N Repeater