Summary of Contents for Bloomfield 8730
- Page 1 OWNERS MANUAL COFFEE GRINDER MODEL: 8730 Includes: Installation Operation Use & Care Servicing Instructions Model 8730 Coffee Grinder PRINTED IN UNITED STATES OF AMERICA p/n 70385 Rev. A ECN-12617 M765 0212 cps...
-
Page 2: Warranty Statement
The prices charged by Bloomfield Industries for its products installation or eighteen (18) months from the date of shipment are based upon the limitations in this warranty. -
Page 3: Table Of Contents
SPECIFICATIONS AMPS POWER SUPPLY MODEL STYLE VOLTS WATTS 1ø CORD NEMA 5-15P 8730 Single Grinder VARIOUS* * contact factory for specific application APPLICABILITY This manual applies to the following Bloomfield Industries products: 8730, with or without suffix... -
Page 4: Features & Operating Controls
FEATURES AND OPERATING CONTROLS Fig. 1 Model 8730 Features & Operating Controls... -
Page 5: Precautions & General Information
PRECAUTIONS AND GENERAL INFORMATION WARNING: ELECTRIC SHOCK HAZARD All servicing requiring access to non-insulated components must be performed by qualified service personnel. Do not open any access panels which require the use of tools. Failure to heed this warning can result in electrical shock. WARNING: INJURY HAZARD All installation procedures must be performed by qualified personnel with full knowledge of all... -
Page 6: Installation Instructions
Electrical shock will cause death or serious Models 8730 are equipped with a cord and plug. injury. 120V units require a 115 - 125 volt 20 amp circuit (50/60 Hz, 2 wire plus ground, with NEMA 5-15R or 5-20R Receptacle). - Page 7 Fig. 2 Adjustment Access Increase time by turning the control knob clockwise. Decrease time by turning the control knob counter-clockwise. SUGGESTIONS: Bloomfield recommends that throw weight be measured with a digital gram scale. Consult with your coffee roaster for recommended grind and throw weight.
-
Page 8: Operation
OPERATION CAUTION: NORMAL OPERATION CUT / PINCH Fill the hopper with coffee beans. HAZARD Place the appropriate filter paper in your brewer’s brew chamber. Slide DO NOT reach into the the brew chamber under the grind head on the guide rails. hopper or discharge chute Press the start button. -
Page 9: Cleaning Instructions
CLEANING INSTRUCTIONS PROCEDURE: Clean Coffee Grinder CAUTION: SHOCK HAZARD PRECAUTIONS: Disconnect grinder from electric power. Do not submerge or immerse FREQUENCY: Weekly grinder in water. TOOLS: Mild Detergent, Clean Soft Cloth or Sponge IMPORTANT: Soft Bristle Brush DO NOT use steel wool, sharp objects, or caustic, abrasive or chlorinated cleansers to clean 1. -
Page 10: Servicing Instructions
SERVICING INSTRUCTIONS ADJUST GRINDER BURRS After replacing grinder burrs, or to compensate for wear from extended use, it may be necessary to adjust the burrs. Empty the hopper and run the grinder until there are no more beans in the burrs. Remove the front access panel. Note the position of the grind adjustment. -
Page 11: Wiring Diagrams
WIRING DIAGRAM... -
Page 12: Exploded View & Parts List
EXPLODED VIEW & PARTS LIST 8730 CABINET AND ASSOCIATED COMPONENTS... - Page 13 EXPLODED VIEW & PARTS LIST (continued) 8730 MOTOR & GRINDER COMPONENTS...
- Page 14 Bloomfield Industries proudly supports CFESA Commercial Food Equipment Service Association Bloomfield Industries, Inc. Division of Carrier Commercial Refrigeration In US and Canada Telephone: 775-689-5700 Fax: 888-492-2783 Fax: 800-356-5142 ( for orders only website: www.wellsbloomfield.com PRINTED IN UNITED STATES OF AMERICA...
Need help?
Do you have a question about the 8730 and is the answer not in the manual?
Questions and answers