Table of Contents
Advertisement
QUICK REFERENCE
To assist you with the installation and maintenance
service of your new spa, please fill out the following
information and keep it on hand for future reference.
Spa Information
Spa
Model:
Serial Number:
Dealership:
Dealer's Phone Number:
Date Purchased:
Date Installed:
Contractor Information
General
1. Name:
Telephone:
2. Name:
Telephone:
2016 V&B Owners Manual.indd 1
Electrician
1. Name:
Telephone:
2. Name:
Telephone:
Concrete, Decking, and Masonry
1. Name:
Telephone:
2. Name:
Telephone:
Landscaping
1. Name:
Telephone:
2. Name:
Telephone:
1
3/3/2016 1:44:05 PM
Advertisement
Table of Contents
Troubleshooting
Related Manuals for Villeroy & Boch A8
Summary of Contents for Villeroy & Boch A8
-
Page 1: Spa Information
QUICK REFERENCE To assist you with the installation and maintenance Electrician service of your new spa, please fill out the following 1. Name: information and keep it on hand for future reference. Telephone: 2. Name: Spa Information Telephone: Concrete, Decking, and Masonry Model: 1. -
Page 2: Table Of Contents
TABLE OF CONTENTS Quick Reference: Table of Contents: Important Overview: Safety Instructions: Getting to Know Your Spa: Equipment Compartment: Filling Your Spa: STIL/A Series Touch: A Series Spas (A900): R Series Spas (R600): X Series Spas: Jetpaks and Jets: Water Care and Chemistry: Spa Maintenance: RCD Wiring Diagrams: Display and Error Messages:... -
Page 3: Important Overview
For the safety of all those who utilize your spa and its surround- ings, please make sure your spa and any adjoining installations, Premium Series: A8, A8L, A8D, A7, A7L, A6L, & including the electrical hook-up, are completed only after acquir- ing any necessary approvals and permits from your local city and/ Comfort Series: R8, R8L, R7, R7L, R6L &... -
Page 4: Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS Safety Instructions SHOULD NOT USE A SPA OR HOT TUB. When installing and using this electrical equipment, basic safety WARNING: TO AVOID INJURY, EXERCISE CARE WHEN precautions should always be followed, including the following: ENTERING OR EXITING THE SPA OR HOT TUB. 1. - Page 5 CAUTION: Location of Your Spa. Locate your spa on a foundation that can support the maximum filled weight of your spa along with the weight of all the occupants using the spa (see Site Selection and Preparation). Also, locate your spa in an environment that can withstand repeated exposure to water and the possibility of a major spill.
- Page 6 2016 V&B Owners Manual.indd 6 3/3/2016 1:45:09 PM...
-
Page 7: Getting To Know Your Spa
GETTING TO KNOW YOUR SPA Spa Overview [A7L Pictured] Hip & Wrist Jets Water Feature Control Valve Water Feature Stereo Speakers (Optional) Suction Fitting Comfort Pillow SnapCap Auxilliary Control Pad (A Series Only) Drain Lighted Cup holder (A Series Only) Ozone Jet Filter SnapCap Weir Door/Filter Plate... -
Page 8: Spa Overview
Spa Overview [X Pictured] Water Feature Control Valve Therapy Jets Stereo Speakers Water Feature (Optional) Suction Fitting Comfort Pillow Perimeter Lights Light Cup Holder Drain Ozone Jet Weir Door/Filter Plate Foot Jets Equipment Compartment Control Pad Calf Jets 2016 V&B Owners Manual.indd 8 3/3/2016 1:45:27 PM... -
Page 9: Equipment Compartment
EQUIPMENT COMPARTMENT Ozone* Control Center Light Safety Certificate Water Heater Pump 1 Pump 2 Drain Outlet *Optional 2016 V&B Owners Manual.indd 9 3/3/2016 1:45:31 PM... -
Page 10: Filling Your Spa
FILLING YOUR SPA WARNING: Cover locks are an essential component for compliance with the An empty spa (spa without water in it) must not safety standard for spa covers. be left exposed to sunlight as shell damage may occur. Once the spa is unwrapped, fill spa with water immediately or shade the spa with Control System cover or wrapping to prevent direct exposure to sunlight. -
Page 11: The Settings Screen
DESIGN & PREMIUM TOUCH SPAS the main menu. 2:15pm ° Preparation To operate: Ensure the spa is filled to its correct operating level. After turning the power on at the The Settings Screen main power panel, the control The “Settings” screen is accessed by pressing the icon. - Page 12 Heat Mode Ready vs. Rest Light Settings When in “Ready” mode, the pump that circulates water through the heater (heater pump)will turn on every 1/2 hour to measure water temperature, heat if needed, and refresh the temperature Interior Exterior display. When in Ready mode your spa will continually maintain its set temperature.
- Page 13 Time Settings key to move to the second page of the menu. Press the icon. The “Units” menu will then be displayed. To change the Setting the time of day temperature setting, press the temperature unit which is currently displayed. This will change it from C° to F° or vice versa. Setting the time is important for filtration settings and other background settings to function as expected.
- Page 14 Language Turn on your Bluetooth device and place within 20 feet (6 meters) of your spa. The device must have “line of sight” to the To change the display language, press the menu. In the spa control panel/equipment door area. Settings menu press the key to move to the second page NOTE:...
- Page 15 PREMIUM LINE SPAS Set Temperature adjustment, can be accessed from this screen. Th e actual water temperature can be seen in large text and the desired, or Set Temperature, can be selected and adjusted. Time of day, ozone operation, and fi lter operation status is available, along with other messages and alerts.
- Page 16 The Settings Screen Press-and-Hold If an Up or Down button is pressed and held when the The Settings Screen is where all programming and other spa Set Temperature is selected, the temperature will continue to behaviors are controlled. This screen has several features that can change until the button is released, or the Temperature Range be acted on directly.
- Page 17 hour, the System will revert to Rest Mode. Th is mode can also mode, it is recommended that you adjust the fi ltration cycles to be reset by entering the Settings Menu and changing the Heat run just prior to the time of your usual spa use. Mode.
- Page 18 Unlocking Pressing the Select Button when Color is highlighted will cycle through 5 background colors available in the control. An Unlock Sequence using the navigation buttons can be used from the Lock Screen. Th e Unlock Sequence is the same for both Language Panel Lock and Settings Lock.
- Page 19 After approximately 15-20 seconds, “PPGME60” will appear in the Bluetooth device list on your electronic device. Select “PPGME60” from your device’s list to connect and “pair” your device to the Life Audio system. After a few seconds the pairing will complete and audio from your device will start playing on the spa audio system.
- Page 20 COMFORT LINE SPAS then again to switch to high-speed. Next, if your spa is equipped with a second pump press the Jets 2 or “Aux” button twice, to turn it on high. The pumps will now be running in high-speed to facilitate priming.
- Page 21 to choose a stationary spa light color or a colored changing series. Press several times until “PREF” displays on the display. Each time the light is turned off and then on it will advance Press the button to enter the Preferences Menu. “F/C” according to the following sequence: will display on the display.
- Page 22 Flip Display “FLTR1” appears on the display. 2. Press button, “BEGN” will appear. This indicates To flip the display, press until the display reads “FLIP.” Press Filter Cycle 1’s “begin time.” key. This will invert the display. 3. Press button again. The hour digit will flash. Press Restricting Operation button or button to adjust hour.
- Page 23 The cleanup cycle, is a maintenance cycle designed provide The first time you use your Bluetooth device with a Life Audio additional circulation and filtration between regular filter cycles. system you must first “pair” your device to the spa audio system. It runs 30 minutes after each spa use.
-
Page 24: X Series Spas
X SERIES SPA CONTROL SYSTEM the set temperature. To change the temperature adjustment direction (from increase to decrease), pause 5 seconds between Jets 1 pressing “Temp,” then push “Temp” again to desired temperature. After 3 seconds, the LCD will again display the current spa water temperature. -
Page 25: Preset Filter Cycles
button on, then off, then wait about 1 second and turn on again. A different color option will appear*. The LED light will turn off automatically after 1 hour. Color options: Each time the light is turned on and off it will advance according to the following sequence: 1. -
Page 26: Jetpaks And Jets
JETPAKS & JETS Interchanging JetPaks- Premium Series,Comfort Series, and Design Series Step 1: Put the spa in “Hold”, this will prevent the pump(s) from activating (see Control Systems). Step 2: Remove the head rest and Snap-Cap by lifting upwards. Jets Jet Types A unique combination of the finest jets available are chosen to optimally balance each JetPak with ideal performance and... - Page 27 Adjustable Jets X Series Spas To adjust the water flow on adjustable jets, simply turn the outer ring. • To increase jet water pressure, turn the outer ring clockwise • To decrease jet water pressure, turn the outer ring counter clockwise NOTE: Turning off jets will increase pressure to other jets on...
-
Page 28: Water Care And Chemistry
WATER CARE & CHEMISTRY Chemicals million) Step 6: Startup water chemistry is now complete. However, it Properly maintaining your spa water is very important to may take additional time for the filter to completely clear the ensure enjoyment in using your spa and to maximize spa shell water. -
Page 29: Water Chemistry
• Bromine Level: 3.0 to 6.0 PPM (parts per million) 454.6 l). Super Sanitation or Spa Shock Cloudy Water Prevention and Control: There are two basic reasons that spa water becomes cloudy. First, non-filterable Normal sanitation does not eliminate non-filterable wastes, liquid waste (e.g. -
Page 30: Spa Maintenance
SPA MAINTENANCE WARNING: NOTE: An empty spa (spa without water in it) must not Th e drain spout will not drain when fully extended. be left exposed to sunlight as shell damage may occur. Once the Step 5: Attach a standard garden hose. Push the drain spout in spa is unwrapped, fi ll spa with water immediately or shade the spa halfway to actuate the drain. - Page 31 the main power off to the spa (X Series). Spa Shell Care The spa cover is an essential part of the spa system. It will both protect the spa and to provide the highest possible efficiency. To ensure you have the best experience possible, ensure the cover is in place except during spa use.
-
Page 32: Miscellaneous Care
WARNING: held spa vacuum available at your Villeroy & Boch dealer. A non-secured, improperly secured, or damaged cover may pose a safety threat to children and may also cause Low-Use or No-Use Periods damage or injury if blown off by wind. Always remove entire During certain times of the year, you may not use the spa on a cover before using the spa. - Page 33 Step 6: Step 2: Remove filter cartridge(s), clean, and reinstall. Remove Door – Once both front corners are removed, look on each side of the front door to see the snap feature built Step 7: Secure the cover to the spa utilizing the tie downs and into the cabinet.
- Page 34 Premium, Comfort, & X Series Door Removal Step 1: Remove hardware - Remove all door mounting bolts (2 or 3 per side) and trim strips. Step 3: Starting from one side, secure the first snap into place by pressing firmly on the cabinet door in the location indicated below.
- Page 35 site properly before delivery, so you will experience a smooth and spa, such as sprinklers or a roof edge without rain gutters. efficient delivery as well as obtain optimal use and full enjoyment Avoid areas of direct, prolonged sunlight (if possible). of your spa.
- Page 36 Electrical Outlets, Switches and Devices: pavers or bricks, pea gravel, or crushed rock 1.5” (4cm) or less, or Based upon a reinforced deck. Additionally, your authorized Villeroy & Boch the national and local wiring rules that apply to your area, you Dealer may sell or recommend pre-formed spa pads.
- Page 37 CAUTION: Occasionally a crane is required to install the spa by lifting it to Consult a qualified structural engineer or its final destination. The crane operator will lift your spa over contractor before the spa is placed on an elevated structure or walls, buildings, or any other obstruction and place it as close to deck.
- Page 38 DATE DRAWN DIMENSIONS ARE IN INCHES TOLERANCES: TITLE: CHECKED FRACTIONAL ANGULAR: MACH BEND ENG APPR. TWO PLACE DECIMAL A8 Electrical Chaseway Drawing THREE PLACE DECIMAL MFG APPR. Q.A. INTERPRET GEOMETRIC TOLERANCING PER: COMMENTS: MATERIAL SIZE DWG. NO. Model X6R FINISH...
-
Page 39: Electrical Requirements
Electrical Requirements & Bonding: Based upon the national and local wiring rules that apply to your area, the Control System Box located inside the Installation equipment compartment of your spa must be bonded to all metal equipment, handrails, fixtures, enclosures, pipe, or conduit that Instructions are located within the maximum specified distances. - Page 40 230V~ Equipment This equipment allows for the spas to operate only on a 230V~/50 Hz electrical service. Permanently-Connected 230V~/50Hz, 32A spas require an RCD protected, 230V~50Hz, 32A Single-Service, or 16A Single Service, or 16A-16A x2, 400V~,3N, 50Hz, 16Ax3, dedicated electrical circuit. It is important that this circuit is dedicated (not being used by any other electrical appliance) or the spa may not function properly.
-
Page 41: Rcd Wiring Diagrams
TP (MAIN) PANELS J30=TEST J31=CE J34 OR J35 IR Receiver RF Receiver J5 (A1-A4) F6 30A MAIN MAIN 230V F8 30A WiFi J8 (A5-A8) Transceiver 115V 115V J108 J107 J109 J34 OR J35 F3 0.3A SLO-BLOW J101 SERIAL LOCATION DEVICE... - Page 42 General Messages Most messages and alerts will appear on the main screen. Several alerts and messages may be displayed in a sequence. Some messages can be reset by pushing the “jets” button. – – –°F – – –°C Water Temperature is Unknown After the pump has been running for 1 minute, the temperature will be displayed.
- Page 43 DISPLAY MESSAGES & ERROR MESSAGES Sensors are out of sync The temperature sensors MAY be out of sync by 2°F or 3°F. Call for Service. Sensors are out of sync -Call for service* The temperature sensors ARE out of sync. The fault above has been established for at least 1 hour. Call for Service. Sensor A Fault, Senor B Fault –...
- Page 44 Change the water Will appear every 100 days. Change the water in the spa on regular basis to maintain proper chemical balance and sanitary conditions. Change the filter Will every 365 days. Filters should be replaced occasionally to maintain proper spa function and sanitary conditions. Reminder messages can be reset from the control panel.
- Page 45 Heater-Related Messages Heater-Related Messages Heater-Related Messages Heater-Related Messages Heater Flow is Reduced (HFL) Heater Flow is Reduced (HFL) Heater Flow is Reduced (HFL) There may not be enough water fl ow through the heater to carry the heat away from the heating element. Heater start up There may not be enough water fl...
- Page 46 Sensor Balance is Poor* Sensor Balance is Poor* Sensor Balance is Poor* The temperature sensors ARE out of sync. The Sensor Balance is Poor fault has been established for at least 1 hour. The temperature sensors ARE out of sync. The Sensor Balance is Poor fault has been established for at least 1 hour. The temperature sensors ARE out of sync.
-
Page 47: Troubleshooting Guide
TROUBLESHOOTING GUIDE This guide will assist in solving simple problems with the spa. If the problem cannot be solved using these procedures, contact your authorized Villeroy & Boch Dealer. Control panel displays an error message: Cause: An error has occurred. Solution: See Diagnostic Messages for specific errors. - Page 48 VILLEROY & BOCH LIMITED WARRANTY Villeroy & Boch extends warranty coverage solely to the end-user purchaser (“Owner”) of any Premium line, Comfort line, X Series line and Just Silence line spa manufactured on or after February 15th, 2013 for 2013 models and later models installed for residential use in Europe.
- Page 49 Exclusions This Villeroy & Boch warranty is void if any of the following occur: • The spa has been subject to alteration, neglect, misuse or abuse. • Any repairs are attempted by anyone other than an authorized agent of Villeroy & Boch. •...
- Page 50 Für Deutschland, Österreich und die Schweiz: Villeroy & Boch AG Unternehmensbereich Bad und Wellness Postfach 11 22 • 66688 Mettlach DEUTSCHLAND Tel. + 49 (0) 68 64 81 15 00 Fax: + 49 (0) 68 64 81 14 84 E-mail: information@villeroy-boch.com For United Kingdom: Villeroy &...
-
Page 51: Owners Manual
Villeroy & Boch OWNERS MANUAL 2016 V&B Owners Manual.indd 51 3/3/2016 1:47:04 PM...
Need help?
Do you have a question about the A8 and is the answer not in the manual?
Questions and answers