Related Manuals for Husky HUG-800GSN
Summary of Contents for Husky HUG-800GSN
- Page 1 HUG-800GSN HUG-800GSEN Industrial 8 x 10/100/1000Base-T(X) Slim Unmanaged Ethernet Switch User’s Manual V1.0 03-28-2017...
- Page 2 Husky Series Industrial Ethernet Switch Solutions HUG-800GSN & HUG-800GSEN Industrial Slim Unmanaged Ethernet Switch User’s Manual Copyright Notice Copyright © 2017 Ethernet Direct Corp. All rights reserved. Reproduction in any form or by any means without Ethernet Direct prior written permission is prohibited.
-
Page 3: Table Of Contents
Table of Contents Chapter 1 Introduction ................................1-1 ............................1-1 1-1 Overview ..........................1-1 1-2 Product Features ..........................1-1 1-3 Package Checklist Chapter 2 Hardware Installation.............................2-1 ............................2-1 2-1 Panel Layout ............................ 2-2 2-2 LED Indicators ............................2-2 2-3 DIP Switch ............................2-2 2-4 RJ-45 Ports 2-4.1 RJ-45 Pin Assignments..........................2-3 .................... -
Page 4: Chapter 1 Introduction
Package Checklist 1-1 Overview The new and more powerful Husky Series HUG-800GSEN is an Industrial 8-ports Slim Unmanaged Full Gigabit Ethernet Switch that which supports IEEE 802.3/802.3u/802.3ab/802.3x with 10/100/1000Mbps, full/half duplex and MDI/MDI-X auto-sensing RJ-45 ports. The compact switch is equipped wide range redundant dual power input 12/24/48VDC and alarm relay contact, with IP30 compact size robust enclosure for easy installation. -
Page 5: Chapter 2 Hardware Installation
Hardware Installation This chapter contains information on HUG-800GSN & HUG-800GSEN’s appearance and hardware installation. Topics include: Panel Layout LED Indicators DIP Switch RJ-45 Ports Installing Your Ethernet Direct Switch 2-1 Panel Layout Panel Layout of HUG-800GSN & HUG-800GSEN Industrial Slim Unmanaged Ethernet Switch... -
Page 6: Led Indicators
There is no Ethernet connection 2-3 DIP Switch There is DIP switch located on the top panel of HUG-800GSN & HUG-800GSEN. It provides setup options on power alarm, EEE (Green Ethernet) and broadcast storm protection (BSP), and these functions as described in the table below. -
Page 7: 2-4.1 Rj-45 Pin Assignments
Hardware Installations 2-4.1 RJ-45 Pin Assignments All ports on HUG-800GSN & HUG-800GSEN support automatic MDI/MDI-X function, users can use straight-through cables (see figure below) for all network connections to PCs or servers, or to other switches or hubs. When auto MDI/MDI-X is enabled, both type of cable can be used and the interface automatically corrects any incorrect cabling. -
Page 8: 2-5.1 Mounting The Switch
Hardware Installations Unpack the HUG-800GSN or HUG-800GSEN from the packing box. Please refer to Package Checklist section to see if any item is missing or damaged. The installation steps include: Mounting The Switch Wiring The Power Inputs Wiring The Alarm Relay Wiring the Earth Ground Ethernet Cabling. -
Page 9: 2-5.3 Wiring The Alarm Relay
Hardware Installations Be sure to disconnect the power cord before installing and/or wiring your switch. Be sure of the maximum possible current when wiring connections. If the current goes above the maximum ratings, the wire could overheat and result in serious damage to your switch. 2-5.3 Wiring The Alarm Relay The alarm relay contact can be wired into an alarm circuit which senses an alarm condition when the contact is broken. -
Page 10: 2-5.5 Ethernet Cabling
Hardware Installations Loosen or remove the grounding screw. Attach the grounding screw to the ring-type or fork-type terminal of the grounding cable. Make sure that the grounding cable is long enough to reach the earth. Use a screwdriver to fasten the grounding screw. Ring-type Fork-type Terminal... -
Page 11: Appendix A Specifications
Specifications HUG-800GSN & HUG-800GSEN Product Specifications are as follows: Hardware Interface 8 x 10/100/1000Base-T(X) auto-negotiation speed, Full/Half duplex mode, RJ-45 Ports auto MDI/MDI-X Per Unit PWR1 (Green), PWR2 (Green), Fault (Amber) LEDs Per Port 100 (Green), 1000 (Yellow) DIP 1: OFF (Enable power failure alarm) / ON (Disable) - Page 12 Specifications Jumbo Frame 9.6K Regulatory Approvals CE, EN 61000-6-2, EN 61000-6-4 FCC Part 15 Subpart B Class A,CE EN55022 Class A EN 61000-4-2 EN 61000-4-3 EN 61000-4-4 EN 61000-4-5 EN 61000-4-6, EN 61000-4-8 Railway Application (Track Side) EN 50121-4 (Certified) Shock IEC60068-2-27 Vibration...
-
Page 13: Appendix B Troubleshooting
Troubleshooting Select the proper UTP cables to construct your network. Please check that you are using the right cables. Use unshielded twisted-pair (UTP) or shield twisted-pair (STP) cables for RJ-45 connections: 100Ω Category 3, 4 or 5 cables for 10Mbps connections, 100Ω Category 5/5e cables for 100Mbps connections,100Ω...