Advertisement
MODE BUTTON
1. Press the MODE button to move all functions in loop sequence from one function screen to another when the speed sensor does not detect
any signal input.
2. Press the MODE button to move partial functions in loop from one function screen to another
when speed sensor detects signal input.
MODE
RESET BUTTON
1. Press MODE button to the desired screen then press RESET button for
2 seconds to reset TRIP 2, MAX, and MAX RPM data from stored
values to zero individually.
2. The data of TRIP 1, AVG & RT can be reset at the same time when one
of the three data functions is being reset.
3. ODO, Clock and TT data cannot be reset.
SHIFT RPM WARNING OPERATION
1. Press MODE button to the RPM screen; pull on the throttle until the desired
shift RPM warning displayed.
2. Press RESET button to confirm and set up the shift warning RPM.
3. Bar-graphic tachometer will flash to warning you shift gear.
1. The details below have been calculated using the following formula; Tire Diameter (inch) x 25.4(mm/inch) x 3.1416 = wheel circumference (in mm).
2. Identify the tire size of your ATV/Motorcycle when you need to change different tire, and key in the corresponding number shown in the following chart.
Tire Size
Circumference
15 inch
1197mm
16 inch
1277mm
17 inch
1357mm
18 inch
1436mm
1. Setup operations include 12/24hour clock, shift RPM warning, numbers of engine rotations per signal, wheel circumference and units.
These must be set up step by step. The computer will automatic reversion to main screen if no button operation for 75 seconds at any
setting screen.
2. Press both MODE & RESET buttons to go into setting screen. In setting screens, press RESET button to add the flashing digit by 1,
press MODE button to confirm the digital setting and jump to next digit or next setting screen to be set. Press MODE button for 2
seconds at any setting screen to finish the setting and go to main screen.
3. It displays "12 or 24H and XX:XX-XX" symbols and AM/PM in case you select 12H.
4. Press RESET button converts 12/24H, press MODE button to complete the setting and jump to clock digit setting.
5. Press RESET button to increase flashing digit by one; press MODE button to confirm digit setting and jump to next digit.
6. Press MODE button to go to shift warning RPM setting screen after set clock.
7. It displays "rXXX00 RPM". Press RESET button to increase flashing digit by one; press MODE key to confirm digit setting and jump
to next digit.
8. Press MODE button to go to numbers of engine rotations per signal setting screen after completed shift warning RPM setting.
9. It displays "SPC-X.X RPM", the default value is 1.0; there are 4 options: 1.0, 2.0, 3.0 and 0.5. It means the numbers of engine rotation
per signal. For example the value 2.0 means the engine rotate 2 turns to output a signal.
10. Press RESET button to move in loop sequence from one to another value of the 4 values. Press MODE button to confirm the setting
and go to wheel circumference setting screen.
11. In "cXXXX" display, "c" means "Circumference", following 4 default digits; flashing digit is digit to be set.
12. Press RESET button to increase flashing digit by one; press MODE button to confirm digit setting and jump to next digit.
13. Press MODE button to jump to unit setting screen.
14. It displays KM/h or M/h, each press of RESET button converts unit; press MODE button for 2 seconds to confirm unit setting and
jump to main screen.
15. Press MODE button to find fuel gauge setting, It shows "100r" as default.
Press SET button to change the value (+/- 100r, 250r 510r, off), then press MODE button to confirm and quite. The fuel bar will
disappear if you select off mode.
mode
+
reset
2 sec
mode
2 sec
mode
mode
BUTTON OPERA TIONS
MODE
WHEEL CIRCUMFERENCE TABLE
Tire Size Circumference Tire Size Circumference
19 inch
1516mm
20 inch
1596mm
21 inch
1676mm
22 inch
1756mm
UNIT & WHEEL CIRCUMFERENCE SETTING
mode
reset
mode
mode
MODE
MODE
23 inch
1835mm
24 inch
1915mm
25 inch
1995mm
26 inch
2075mm
mode
mode
mode
Reset
mode
mode
MODE
MODE
MODE
RESET
2 sec
mode
mode
mode
MODE
mode
mode
mode
Advertisement
