Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Ceasa SET&SOFT
Summary of Contents for Ceasa SET&SOFT
- Page 1 SHOWER SOFTENER-CEASA 1...
- Page 2 1. Due to occasional updates, some of the text or designs in the manual may differ from the actual product. Please refer to the actual product. 2. All data has been carefully checked. If there are any printing or content errors, we reserve the right of interpretation. 2 SHOWER SOFTENER-CEASA...
-
Page 3: Table Of Contents
5.3 Regeneration Process 6. Resin Replacement……………………………………………………………………………………………………………………25 7. Parameter Setting…………………………………………………………………………………………………………………….28 7.1 Product Control Panel Overview 7.2 Main Board Socket Overview 7.3 Product Installation Mode Setting 7.4 Regeneration Reminder Day Setting 7.5 Meaning of Operation Codes 8. Troubleshooting……………………………………………………………………………………………………………………….31 9. Warranty Card………………………………………………………………………………………………………………………….32 SHOWER SOFTENER-CEASA 3... - Page 4 12. Since the product needs electricity to operate, please do not install the transformer in a location where water splashes are possible. 13. Our company shall not be liable for any damage resulting from operation not in accordance with the above considerations. 4 SHOWER SOFTENER-CEASA...
-
Page 5: Product List
Hot water connector Installation before the water heater ½" Elbow Installation before the water heater Note: Optional accessories are required to install the product before the water heater. If needed, please purchase from your distributor. SHOWER SOFTENER-CEASA 5... -
Page 6: Product Overview
●Data saved after power off. 2.2. Technical Parameters Item Requirements Work Pressure 0.1～0.6MPa Water Temperature 5℃～70℃ Environment Temperature 5℃～50℃ Transformer AC100～240V/50～60Hz Water regeneration capacity 750L Water inlet/outlet specification G1/2 Regeneration salt consumption 400g Suitable water Tap water 6 SHOWER SOFTENER-CEASA... -
Page 7: Technological Processing Of Water
(total water hardness test in CaCO3, 200 mg/-), and will change under different operating conditions 2.3. Technological Processing of Water Tap Water Na cationic resin Soft water 2.4. Appearance and Dimensions Inlet Drain pipe Outlet Product Diagram SHOWER SOFTENER-CEASA 7... -
Page 8: Structure
B. Installation after the water heater Advantage: The installation after the water heater is convenient for pipeline installation, softens the bathing water, and is suitable for users looking to decorate. 8 SHOWER SOFTENER-CEASA... -
Page 9: Product Installation
This product should be installed at around 1 meter from a reliable worldwide floor drain. Product wall-mounting steps: 2.1 Open the package and check if the softener is complete and all accessories are included. SHOWER SOFTENER-CEASA 9... - Page 10 2.5 Install the unit on the slots of the fixed plate, then complete the hanging process. The appearance after installation is shown in figure 3. Self-tapping Stainless steel plate Expansion screw tube screw Figure 1. Install the stainless steel plate 10 SHOWER SOFTENER-CEASA...
-
Page 11: Pipeline Installation Instructions
1.1 Close the water mixing valve; use an adjustable wrench to unscrew the hand-held shower nozzle and the nut from the water mixing valve connection as shown in figure 4. Tighten the nut of the shower head to the outlet of the unit, as shown in figure 5. SHOWER SOFTENER-CEASA 11... - Page 12 If the surrounding space already has a spare faucet installed, the unit can be installed to the left or the right of the water mixing valve depending on the space available, as shown in figure 6 and figure 7. 12 SHOWER SOFTENER-CEASA...
- Page 13 Figure 6. Installation diagram of the unit on the left side of the water mixing valve Use bellows joint or tube Suggested distance: less than 300mm Figure 7. Installation diagram of the unit on the right side of the water mixing valve SHOWER SOFTENER-CEASA 13...
- Page 14 8 and figure 9. Reserved outlet Figure 8. Installation diagram of the unit on the right side of the water mixing valve using the reserved outlet 14 SHOWER SOFTENER-CEASA...
-
Page 15: Installation Before Water Heater
Required accessories Name Diagram Remarks On the connector Hot water connector engraved with “H” On the connector Cold water connector engraved with “C” Cut-off Selection filter valve ½" Elbow SHOWER SOFTENER-CEASA 15... - Page 16 Take out the cut-off filter valve and flat gasket, tighten the cold water connection to the tap water connection, placing the flat gasket as shown in figure 14. Appearance after installation is shown in figure 15. 16 SHOWER SOFTENER-CEASA...
- Page 17 ¾" Flat gasket Hot water port connector Cold water port connector Figure 12. Installation of cold and hot water connectors ½" flat gasket Cut-off filter valve Figure 13. Appearance after installation Figure 14. Installation diagram of cut-off filter valve SHOWER SOFTENER-CEASA 17...
-
Page 18: Drain Pipeline Installation
Choose the appropriate position to hang the unit on the wall (with reference to the previous product installation instructions). Back outlet ½" Articulated elbow End cap ½" Flat ½" Flat gasket gasket Figure 16 Figure 17 Figure 18 18 SHOWER SOFTENER-CEASA... - Page 19 Figure 21 shows a closeup of the cold water connection. Water heater Embedded pipe installed Outlet connected to water heater Outlet connected to cold water connection Cut-off filter valve Figure 19. Diagram of installation before the water heater Water heater SHOWER SOFTENER-CEASA 19...
- Page 20 1/4" quick connector. Pay attention to the flow control connector. The drain hose is correctly installed when connected as shown in figure 22. Please contact your distributor if you lose it. 20 SHOWER SOFTENER-CEASA...
-
Page 21: Power Wire Installation
This product needs the power supply to be located far away from water mist when the device is installed. The power plug uses a seal design. For installation, please tighten the power wire connector nut as shown in figure 23. Power wire connector nut Figure 23 SHOWER SOFTENER-CEASA 21... -
Page 22: Trial Run
40 L per day for a family of three. Water hardness Water capacity Time until regeneration 200mg/L 750L About 6 days 400 mg/L 320L About 3 days The user can make calculations based on actual water use if the water hardness is 450mg/L. 22 SHOWER SOFTENER-CEASA... -
Page 23: Regeneration Salt Consumption
3 seconds until you hear a beep. The device enters the regeneration mode, the motor rotates, the display screen shows , when backwash is reached, the display screen shows and water comes out of the drain; it remains in state for 30 SHOWER SOFTENER-CEASA 23... - Page 24 Note: After regeneration, there could be a small amount of water in the switching station outlet. Please make sure it doesn’t spill on the unit. Remove the upper cover Regeneration salt Figure 24 Figure25 Figure 26 24 SHOWER SOFTENER-CEASA...
-
Page 25: Resin Replacement
Take out the front cover from the unit, and handle with care to avoid causing damage. d. Using a cross-head screwdriver, screw out the 4 screws that fix the resin tank to the back cover. SHOWER SOFTENER-CEASA 25... - Page 26 3. Please make sure the drain line flow control is intact when installing the drain pipe. Take out 6 screws with a screwdriver Drain line flow control Take out back cover screw Remove drain pipe Front cover 4 screws Remove front cover Remove resin tank screw 26 SHOWER SOFTENER-CEASA...
- Page 27 Take out resin tank and valve assembly Resin tank cover Take out resin tank assembly Unscrew resin tank cover Top strainer Press the riser pipe and pour resin Take out top strainer h. Pour resin SHOWER SOFTENER-CEASA 27...
-
Page 28: Parameter Setting
Display area Regeneration/confirm button Set button 7.2. Main Board Socket Overview Power socket Motor socket Locating board Flow meter socket socket Sockets on the main board are one-to-one. Follow the color and number of pins to insert. 28 SHOWER SOFTENER-CEASA... -
Page 29: Product Installation Mode Setting
Installed after water select the mode, then press heater, meter type save and quit. Installed before water heater, meter type Inquire mode: Power on again, and the interface will display the installation mode. SHOWER SOFTENER-CEASA 29... -
Page 30: Regeneration Reminder Day Setting
“111”, then after a while, it will show “11”, then “1”. When the treated water is used up (the water capacity is reached), the “1” will flash to remind you to start the regeneration. 30 SHOWER SOFTENER-CEASA... -
Page 31: Meaning Of Operation Codes
4． Clean moving disc and fixed disc E2 flashes 1. Wiring of locating board is 1. Replace locating board wiring faulty 2. Replace control board 2. Control board failure E3 flashes Control board failure 1. Replace control board SHOWER SOFTENER-CEASA 31... -
Page 32: Warranty Card
9. WARRANTY CARD Dear client, This warranty card is the proof of warranty of the CEASA Shower Softener. The client is responsible for keeping it. It allows you to request after-sales services from the supplier appointed by the manufacturer CEASA. Please store it properly. If lost, it cannot be replaced. - Page 33 COMPAÑÍA EUROPA DEL AGUA, S.A. ADDRESS: C/R.F. Alemania 21-25, Polígono Industrial Rosanes Castellví de Rosanes, Barcelona Postal code: 08769 TEL.: (00 34) 937 766 344 FAX: (00 34) 937 766 344 WEB: http://www.ceasaespana.com E-mail: info@ceasaespana.com SHOWER SOFTENER-CEASA 33...