Summary of Contents for Telikou MS-800T
- Page 1 TELIKOU Intercom System MS-800T Main Station Instruction Manual © TELIKOU Systems All Rights Reserved...
- Page 2 TELIKOU MS-800T Eight Channel Main Station I. Introduction Thank you for choosing TELIKOU intercom product. MS-800T main station is suitable for television station, communication center, UB truck, live performance and any other environment which requires communication. We recommend you read through this manual to better understand the functions of MS-800T.
- Page 3 This switch is without self-locking function, release and reset. 5. Tone Alert Level Control When MS-800T receives external call signal, the internal buzzer will sent a hum to panel speaker and earphone. This knob adjusts the hum level. 6. Mic Select Switch Set the Mic select switch to select whether the panel microphone or the headset microphone is active.
- Page 4 TELIKOU MS-800T Eight Channel Main Station Pin 1 -- Mic common Pin 2 -- Mic hot Pin 3 -- Null 8. Headset connector 4-pin XLR Male or 5-pin XLR Female EARPHONE: Dynamic 50-2000 ohm MICROPHONE: Dynamic 100-600 ohm The wiring of headset is as follow: Pin 1—Mic.
- Page 5 It will be interrupted when microphone is turned on. 19. Power LED This green LED constantly lights on when power supply working properly. If MS-800T meets any circuit short problem, it will keep on flashing until the problem has been solved.
- Page 6 21. Sidetone zero-adjusting The MS-800T uses full-duplex audio in which the talk and listen audio are sent and received on the same line. Thus, when you talk on a channel, you will also here your own voice back in the speaker or earphone.
- Page 7 TELIKOU MS-800T Eight Channel Main Station Pin 3 --- Audio Pin 4 --- Control Signal Pin 5 --- Null 23. Termination switch When this switch is turned to ON position, one 220 ohm termination resistor will be connected to intercom line. If the intercom system is not terminated, the level of intercom line will be too high, and the system stability will be influenced.
- Page 8 Pin 9 --- +12VDC Shell --- Ground MS-800T is negative logic as default. It can be set to positive logic. The step is as follow: Turn off the power. Open the top cover of MS-800T. Plug the DB9 connector to the proper slot.
- Page 9 V Troubleshooting Problem: Power LED wink Cause 1: Direct short on the intercom channel Solution 1: Remove all the intercom cables from MS-800T. Check each channel one by one, until find the short channel. Cause 2: Overload Solution 2: Decrease the amount of remote stations.
- Page 10 Solution 2: Adjust. Refer to the procedure in the Front Panel section of this manual. Cause 3: Channel un-terminated. Solution 3: Set the MS-800T termination switch to the ON position. Cause 3: A headset cord is too long or jointing quality.
- Page 11 Problem: Can not turn on the Mic function on all the beltpacks Cause 1: The connection among TELIKOU main stations must go via Online connector on rear panel. The Online connector of this station connected to the Intercom Line connector of another station.
- Page 12 TELIKOU MS-800T Eight Channel Main Station Dynamic 50-2000 ohm MICROPHONE: Dynamic 100-600 ohm CONNECTOR: Panel Mic connector: XLR-3F Pin 1 -- Mic common Pin 2 -- Mic hot Pin 3 – Null Headset connector: XLR-4M or XLR-5F Pin 1--Mic common...
-
Page 13: Power Supply
TELIKOU MS-800T Eight Channel Main Station Pin 5 --- tally signal to channel 5 Pin 6 --- tally signal to channel 6 Pin 7 --- tally signal to channel 7 Pin 8 --- tally signal to channel 8 Pin 9 --- +12VDC...
Need help?
Do you have a question about the MS-800T and is the answer not in the manual?
Questions and answers