Summary of Contents for Liquid Controls 81538
- Page 1 LC-ON THE GO Set-up and Connection Guide Wireless WiFi Adapter P/N 81538 L I Q U I D C O N T R O L S LC_IOM_ONTHEGOWIFIADAPTER V1: 05/17 An IDEX Energy & Fuels Business...
- Page 2 Content is subject to change without notice. your local distributor. www.LCmeter.com 05/2017 LC-ON THE GO Wireless WiFi Adapter © Copyright 2017 by Liquid Controls, LLC. WARNING Before using this product, read and understand the instructions. Save these instructions for future reference.
-
Page 3: Table Of Contents
TABLE OF CONTENTS I. Basic Set Up ....................4 II. Connecting to a Single Meter System ............7 III. Connecting to an Existing Dual Meter System ..........8 IV. Connecting to a New Dual Meter System .............9 V. Connecting to EZ Command or EZ Command Lite ........12 LC-ON THE GO Wireless WiFi Adapter WWW.LCMETER.COM 3... -
Page 4: Basic Setup
SSID link to display the connect screen. Note: The SSID can be customized by the user. (See Also required (sold separately): section 5. Entering the Liquid Controls Configuration Mode. Lap pad adapter (81514) for single meter system Multiplexer box (E25352) for dual meter system... - Page 5 Open a web browser and navigate to 192.168.0.1. Password: onthegowifi Enter default User Name and Password. (Note: both are case sensitive). Note: the password can be changed via the configuration interface (See section 5. Entering the Liquid Controls User Name: admin Configuration Mode) Password: PASSWORD LC-ON THE GO Wireless WiFi Adapter WWW.LCMETER.COM 5...
-
Page 6: Changing The Password
I. BASIC SETUP 6. Default Key Configuration Settings 7. Changing the SSID: Enter the Admin Screen and click on NETWORK, “LINK” and “Configuration” Click on the SSID and assign a new SSID. Click to submit the new SSID. The unit will update and disconnect. -
Page 7: Connecting To A Single Meter System
II. CONNECTING TO A SINGLE METER SYSTEM 9. Setting Up A Single Meter System A single meter system consists of a meter, an electronic register and a printer. The ON THE GO WiFi adapter may be used to communicate with the register using Lap Pad adapter 81514. -
Page 8: Connecting To An Existing Dual Meter System
III. CONNECTING TO AN EXISTING DUAL METER SYSTEM 10. Setting up a Dual Meter System – d. Connect the ON THE GO WiFi adapter to the Existing System. RS-232 LAP PAD female DB-9 connection on the front of the multiplexer box. A dual meter system consists of 2 meters, 2 electronic registers, a multiplexer box and a printer. -
Page 9: Connecting To A New Dual Meter System
IV. CONNECTING TO A NEW DUAL METER SYSTEM 11. Setting up a Dual Meter System – NEW e. Install the Multiplexer and connect the printer. System. Install the multiplexer in its final location and make sure it is grounded properly. Next, plug A dual meter system consists of 2 meters, 2 in the data and the power cable into the front electronic registers, a multiplexer box and a printer. - Page 10 IV. CONNECTING TO A NEW DUAL METER SYSTEM h. Connect Register Data and Power cables. Run the register’s data and power cables through split loom, under the vehicle and connect them to the multiplexer box as shown: i. Set up the Register’s Communication Protocol NOTE: Make sure the register is powered OFF before moving the jumper or the cables.
-
Page 11: Connecting To Ez Command Or Ez Command Lite
Config. Enter Local IP Port, Node IP Address, and Node IP Port as follows: SPECIFICATIONS FOR P/N: 81538 ANTENNA ..4.3 inch WiFi Antenna SECURITY/PROTECTION . . 256-bit AES Encryption . - Page 12 L I Q U I D C O N T R O L S An IDEX Energy & Fuels Business 105 Albrecht Drive © 2017 Liquid Controls LC_IOM_ONTHEGOWIFIADAPTER V1: 05/17 Lake Bluff, IL 60044-2242 1.800.458.5262 1.847.295.1050 Fax: 1.847.295.1057 www.LCmeter.com...