1. Manuals
  2. Brands
  3. ROEL electronics Manuals
  4. Control Panel
  5. cerber C41V1
  6. Installation booklet

ROEL electronics cerber C41V1 Installation Booklet

Burglary control panel with built-in voice communicator for your home and office
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Enlarged version
cerber C41v1/v4
installer's book
- 1 -

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the cerber C41V1 and is the answer not in the manual?

Questions and answers

Summary of Contents for ROEL electronics cerber C41V1

  • Page 1 C41v1/v4 installer’s book - 1 -...

  • Page 2: Table Of Contents

    Table of Contents ..................- 2 - built-in telephone dialer, alarm memory and 4 access codes. INTRODUCTION..................- 3 - One 30 second vocal message is available for the Cerber C41V1 control panel FEATURES:..............................- 3 - TECHNICAL SPECIFICATIONS ......................- 4 - Four vocal messages, approx. 15 seconds each, are available for the Cerber G ............- 4 -...

  • Page 3: Technical Specifications

    NOTE: Complete all wiring to the control panel before applying battery or AC power to it. Wiring should be made according to one of the next diagrams, depending on the selected type: Cerber C41V1 or Cerber C41V4. - 5 - - 4 -...

  • Page 4: Connectors

    If the panel is connected to the phone line, when disarming - using this These terminals are used to connect a mini speaker in case of one's wish to particular code, the panel will transmit a phone message to Cerber C41V1 listen to the recorded messages.

  • Page 5: Installer's Code

    C41v1/v4 cerber C41v1/v4 installer’s book installer’s book Code modifying including Master Code by default, is achieved by “INSTANT STAY” ARMING [*][7][“Master Code”] command. [*] [1] [ACCESS CODE] INSTALLER'S CODE This arming mode is used for perimetral protection. Thus, the user can stay The default Installer's Code is “0269”.

  • Page 6: Other Operating Commands

    C41v1/v4 cerber C41v1/v4 installer’s book installer’s book OTHER OPERATING COMMANDS "SYSTEM" LED will blink and so will the LEDs of the alarmed zones. One can press the 1 to 9 keys in order to visualize the first 9 alarm events ZONE BYPASSING during the last arming of the panel.

  • Page 7: O C A L M E S S A G E R E C O R D I N G C H E C K I Ng

    1. Connect a temporary mini-speaker (min. 8Ohm impedance) to the DIF • Cerber c41v1 control panel terminals. For vocal message recording follow the procedure described bellow: 2. Press one of M1-M4 buttons and listen to the respective message. The 1.

  • Page 8: S Y S T E M P A R A M E T E R P R O G R A M M I Ng

    C41v1/v4 cerber C41v1/v4 installer’s book installer’s book in the table bellow: HEX number Enter [*][0] ENTERING THE PROGRAMMING MODE OF SYSTEM Enter [*][1] PARAMETERS Enter [*][2] Enter [*][3] [ * ] [ 8 ] [INSTALLER'S CODE] Enter [*][4] Enter [*][5]...

  • Page 9: Section [10] - Key Zone Definitions

    C41v1/v4 cerber C41v1/v4 installer’s book installer’s book delay without causing an alarm. [ 4 ] STEADY ALARM AND FORCED ARMING When the Exit Delay expires, zone opening will start the Entry Delay. During An alarm message will be send by phone line and the siren will be enabled. The the Entry Delay, the keypad buzzer will sound continuously to indicate that system can be armed even if this zone is not secured.

  • Page 10: Section [12] Installer's Code Changing

    0 = the vocal message is not sent will exit section 12 waiting for a new command. Cerber C41V1 control panel SECTION [13] PROGRAMMABLE OUTPUT OPTIONS FOR 1 = sends the alarm message when one of zones 1-4 is tripped...
  • Page 11 C41v1/v4 cerber C41v1/v4 installer’s book installer’s book The second It is sent a succession consists of programmed The alarm message is sent to: Message 1 Message 2 Message 3 Message 4 digit The second One of Panic from AC Loss...
  • Page 12 C41v1/v4 cerber C41v1/v4 installer’s book installer’s book Default: [ ][ ][ ] [ ][ ][ ] [09] ZONE DEFINITIONS While this system is an advanced design security system, it does not offer guarantee Default Digit 1 Digit 2 against burglary, fire or other emergency. Any alarm system, whether commercial or...
  • Page 13 C41v1/v4 installer’s book The most frequent cause of an alarm system not functioning when an intrusion or fire occurs is inadequate maintenance. This alarm system should be tested weekly to make sure all sensors are working properly. TECHNICAL SPECIFICATIONS...

This manual is also suitable for:

Cerber c41v4

Table of Contents