Advertisement
Introduction
Thanks for choosing the Vision's wireless garage door detector of the home security
device. This sensor is a Z-Wave™ enabled device (interoperable, two-way RF mesh
networking technology) and is fully compatible with any Z-Wave™ enabled network. Every
mains powered Z-Wave enabled device acts as a signal repeater and multiple devices
result in more possible transmission routes which helps eliminate "RF dead-sports"
Z-Wave™ enabled devices displaying the Z-Wave™ logo can also be used with it
regardless of the manufacturer, and ours can also be used in other manufacturer's
Z-Wave™ enabled networks. This detector monitors garage door and send Z-Wave™
signal when angel is changed.
Product Description and Specification
*** For indoor use only***
Specification:
Protocol: Z-Wave™ (ZM3102N)
Frequency Range:
865.22MHz (ZG8101IN)
868.42MHz (ZG8101EU)
869.00MHz (ZG8101RU)
908.42MHz (ZG8101US)
920.00MHz (ZG8101JP)
921.42MHz (ZG8101BR)
Operating Range: Up to 100 feet line of sight
Operating Temp.: -15°C~ 60°C (5°F ~140°F)
Battery: Panasonic CR123A * 1PC
Installation
Notice: If you are installing the entire Z-Wave™ system for the first time, please refer to
the installation guide of Z-Wave™ Interface Controller before installing ZG8101.
1. Install Battery: Use care when installing the battery. Press the locking tab on the top
detector cover, and then gently pull up the cover. Observe the correct polarity before
insert the battery.
2. After insert the battery, the LED will start to flash slowly, which means the sensor has
not yet been "inclusion".
3. For "Inclusion" in (adding to) a network: Put the Z-Wave™ Interface Controller into
Package Content:
1pc
ZG 8101 detector
1pc
Bracket Holder
1pc
Adhesive tape for detector
3pcs
Screw for bracket
1pc
CR123A Lithium Battery
1pc
Installation & Operation manual
-1-
"inclusion" mode, and following its instruction to add the ZG8101 to your controller. To
get in the "inclusion" mode, the distance between sensor and controller is suggested
to be in one meter. Press the program switch of ZG8101 for 1 second at least.
The LED on the ZG8101 should go solid, if not, please try again.
For "Exclusion" from (removing from) a network: Put the Z-Wave™ Interface
Controller into "exclusion" mode, and following its instruction to delete the ZG8101
from your controller. Press the program switch of ZG8101 for 1 second at least to be
excluded.
For "Association": removing the cover of the ZG8101 to get into the "Awake" mode,
then put the Z-Wave™ Interface Controller into "Association", and following its
instruction to associate the ZG8101 with other device. Close the cover back after
"association" done, afterward the ZG8101 will get into "Sleep" mode for power saving.
Support one association group (5 nodes).
"Awake" mode: it is to leave the "Sleep" mode by removing the cover of ZG8101, to
allow the Z-Wave™ Interface Controller to do "Inclusion", "Exclusion", "Association"
and to reply and receive the commands from controller.
6. Slide back the rear cover and screw fastening with the front cover, the LED should go off.
7. Using the adhesive tape or fixing screws to fix the bracket holder with garage detector.
For better operation, please install detector on top portion of garage door.
8. External Switch: If your garage door needs external switch for fully monitoring. You
could use an external switch to connect with the ZG8101 for extending detection. The
ZG8101 has 2 normally closed contact terminals. These can be used for additional
external switch wired contacts. The external switch will send an alarm report
(type:0x07,level:0xFF) by opening the garage door.
-2-
Advertisement
