Related Manuals for T3 Innovation GigTest GT1000
Summary of Contents for T3 Innovation GigTest GT1000
- Page 1 GigTest ™ Ethernet Speed Tester GT1000 / GT1005 User Manual REV 08/21/17 www.t3innovation.com...
-
Page 2: Table Of Contents
GigTest ™ Ethernet Speed Tester User Manual Table of Contents About this Manual..............3 Features................4 Safety Information..............5 Cable Test.................6 Signal to Noise Ratio..............7 Bit Error Rate Test (BERT)............8 Test Settings................9 Buttons................11 WiFi Reporting................12 WiFi Testing................13 Indicator LEDs................14 Connectors...............15... -
Page 3: About This Manual
ABOUT THIS MANUAL Testing and measuring key data link operations is necessary to determine the speed capability of individual CAT 5/6 links within installed LAN network systems. With the push of a button the GT1000 GigTest automatically measures key metrics like Signal to Noise Ratio and Skew as well as generating a Bit Error Rate Test (BERT) that generates data packets for transmission and receiving along a link to see both error generation and/or noise interference effects that may impede data flow at... -
Page 4: Features
FEATURES Usable with premise equipment or with a second GigTest to test data ▪ reliability of a link. ▪ Use a second GigTest to run BERT test. Tests can be saved to GigTest when not linked and uploaded to app ▪... -
Page 5: Safety Information
SAFETY INFORMATION To ensure safe operation of the GigTest™, follow these instructions. WARNING! Do not attach to AC power. The GigTest is designed for use on unenergized cabling systems. Connecting the GigTest to live AC power may damage it and pose a safety hazard for the user. Failure to observe these warnings can result in severe injury or death. -
Page 6: Cable Test
CABLE TEST Bicolor LED indicating pass or fail of a cable test. If 10Mb link, cable test only will be run. If 100Mb is selected, only active two pairs are tested. Cable test primarily tests for cable faults that would prevent the possibility of linking, not a complete wire map. -
Page 7: Signal To Noise Ratio
SIGNAL TO NOISE RATIO LED indicating pass or fail of the SNR test. Cable must pass Cable Test in order to be run. Will test the 1-2 and 3-6 pairs if 100Mb is selected. All four pairs are tested in 1000Mb mode. SNR is reported if connected to a switch or NIC. -
Page 8: Bit Error Rate Test (Bert)
BIT ERROR RATE TEST (BERT) LED indicating pass or fail of BERT test. Will run only if Cable and SNR tests are passed and a second GigTest is at the other end of the cable. This test will show fail if more than 3 errors are detected in the normal length test, or 10 errors in the long length test. -
Page 9: Test Settings
TEST SETTINGS Test Speed Test Speed - Pressing the button below 10000Mb/100Mb LEDs will toggle between the two settings. Test is run only for the data rate selected. Blink Light Pressing the button directly below the Link Blink LED will turn on the LED and enter Link blink test mode. - Page 10 TEST SETTINGS Wifi Pressing the WiFi button toggles the WiFi on and off. The LED above indicates current setting. Long BERT Button press toggles between normal BERT test of about 1x10 bits (10Gbits) transferred and the long BERT test of 1x10 bits (100Gbits) transferred at 1000Mb speed.
-
Page 11: Buttons
BUTTONS Back A test in progress can be canceled by pressing the back button, returning the tester to idle. Only the master can terminate a test in progress utilizing two GigTests testers. Save Press the Save button to save the Press the Save button to save the currently displayed test result. -
Page 12: Wifi Reporting
VIEW GIGTEST RESULTS Turn on GigTest Turn on WiFi WiFi will retain on/off status from previous usage. Connect Phone/Tablet via Wifi to SSID “GigTest-xxxxxx” WiFi will retain on/off status from previous usage. Open GigTest App on Phone/Tablet View GigTest Reports View, Print or Share GigTest Reports CSV or PDF Export Options... -
Page 13: Wifi Testing
MOBILE TESTING Turn on GigTest Turn on WiFi WiFi will retain on/off status from previous usage. Connect Phone/Tablet via Wifi to SSID “GigTest-xxxxxx” WiFi will retain on/off status from previous usage. Open GigTest App on Phone/Tablet Mobile Test View, Print or Share GigTest Reports CSV or PDF Export Options Swipe left and right to switch... -
Page 14: Indicator Leds
INDICATOR LEDS Battery Low/Power On LED LED will be green when power is on and will switch to red when the battery voltage reaches 6.0V. LED will remain on for as long as the unit is powered on. GigTest will power off when battery reaches 5.7 volts. Link Light LED While a Link is established, the Link Light LED will be on. -
Page 15: Connectors
CONNECTORS RJ45 Test Connector Connect to cable to be tested. Micro USB Connect to Windows PC running GigTest Application to update firmware. Manufacturing Connector In battery hole, supports PIC programmer, factory use only. Specifications Battery Life 6X AA alkaline batteries, 9VDC nominal, 2,200 mA-hr (typical) Linked –... - Page 16 GigTest ™ Ethernet Speed Tester User Manual For technical information and customer support, please visit www.t3innovation.com or send an email to support@t3innovation.com. Contact Numbers: Phone: 805-233-3390 Fax: 805-383-4507 Address: 808 Calle Plano Camarillo, CA 93012 www.t3innovation.com...
Need help?
Do you have a question about the GigTest GT1000 and is the answer not in the manual?
Questions and answers