1. Manuals
  2. Brands
  3. American-Lincoln Manuals
  4. Scrubber
  5. SR9772 510-016
  6. Instructions for use manual

American-Lincoln SR9772 510-016 Instructions For Use Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Electronic Service
Manuals
This electronic document is provided as a service to our customers.
We do not create the contents of the information contained in this docu-
ment. Should you have detailed questions pertaining to the information
contained in this document, you may contact Michco, or the manufac-
turer which provided the original information in this electronic deliver-
able. Michco's only part in this electronic deliverable was the electronic
assembly process. By providing this manual on line we are not guaran-
teeing parts availability.
You may contact Michco through the following methods:
Phone (517) 484-9312 or (800) 331-3339
2011 N. High St. -- Lansing, Michigan -- 48906
Fax: (517) 484-9836
Email: CustServe@Michco.com
Web site: www.Michco.Com
Parts Web site: www.FloorMachineParts.Com
Order Parts on Line at:
www.FloorMachineParts.Com
Directly to Parts & Service:
By Email:
Shop@Michco.com
By Fax: (517) 702-2041
By Voice: Use numbers above.
Serving the Cleaning Industry Since 1922
Notice: All copyrighted material remains property of original owners, all trademarks are property of respective owners.
Manuals are subject to Manufacturer's reproduction limitations. Originals or reproductions were provided by manufacturers
through a request. We make no warranty as to the correctness of information provided in this document and you assume
all risk. By placing these manuals on line we are not declaring our corporation to be an manufacturer authorized dealer or
provider, please check our web site for authorized manufacturers we represent.

Advertisement

Table of Contents
loading

Related Manuals for American-Lincoln SR9772 510-016

Summary of Contents for American-Lincoln SR9772 510-016

  • Page 1 Electronic Service Manuals This electronic document is provided as a service to our customers. We do not create the contents of the information contained in this docu- ment. Should you have detailed questions pertaining to the information contained in this document, you may contact Michco, or the manufac- turer which provided the original information in this electronic deliver- able.
  • Page 2 SR9772 SCRUBBER For American-Lincoln MODELS 510-015, 510-016, 510-017, 510-018 Instructions for Use / Parts List READ THIS BOOK This book has important information for the use and safe operation of this machine. Failure to read this book prior to operating or attempt- ing any service or maintenance procedure to your machine could result in injury to you or to other personnel;...
  • Page 3 American Lincoln SR9772...

  • Page 4: Table Of Contents

    Foam-Filled Tires Option ................................3-3 Catalytic Muffl er Option ................................3-4 Rotating Light Option (Roll Bar) ..............................3-5 Warning Light Option (CAB) ............................... 3-6 Vacuum Wand Option ................................. 3-7 Transmission Lock-Out Option ..............................3-8 Additonal Options ..................................3-9 American-Lincoln SR9772...

  • Page 5: Machine Specifi Cations

    MACHINE SPECIFICATIONS DIMENSIONS Length 137.4 inches (3489 mm) Width 52.5 to 75.6 inches (1333 to 1920 mm) Height 94.92 inches ( 2411 mm) WEIGHT Counterweights 925.9 to 1102lbs ( 420/500 kg) Weight Cab Model Loaded 11168 lbs. (5076kg) Weight Cab Model Unloaded 8168 lbs.
  • Page 6 Rear: Para-Bolic 80-inch (203.2 cm) break-away with no-tool squeegee replacement. Side: 26 in (66 cm) Easy Change OPTIONAL BRUSHES Bassine Amergrit Supergrit Soft Nylon Straight wire Amerfi l (.025) Nylon Amerfi l (.040) Amerfi l & wire (one-piece only) American-Lincoln SR9772...

  • Page 7: Machine Dimensions

    MACHINE DIMENSIONS 99.33 76.91 82.00 PLATFORM MODEL (SIDE VIEW) PLATFORM MODEL (SIDE VIEW) 59.89 66.65 84.89 PLATFORM MODEL (REAR VIEW) PLATFORM MODEL (REAR VIEW) 84.75 c0976/1202 PLATFORM MODEL (TOP VIEW) PLATFORM MODEL (TOP VIEW) American Lincoln SR9772...
  • Page 8 MACHINE DIMENSIONS CAB MODEL (SIDE VIEW) CAB MODEL (SIDE VIEW) CAB MODEL (REAR VIEW) CAB MODEL (REAR VIEW) CAB MODEL (TOP VIEW) CAB MODEL (TOP VIEW) American-Lincoln SR9772...

  • Page 9: Safety Precautions

    SAFETY PRECAUTIONS FOR SAFETY, OBSERVE THE FOLLOWING WARNINGS. FAILURE TO COMPLY MAY CREATE A SERIOUS RISK OF INJURY TO YOU AND OTHERS. THIS MACHINE SHOULD NOT BE USED IN HAZARDOUS LOCATIONS, INCLUDING AREAS OF VOLATILE DUST OR VAPOR CONCENTRATIONS. READ THE MANUAL CAREFULLY. UNDERSTAND WHEN THESE CONDITIONS CAN EXIST; THEN TAKE NECESSARY STEPS TO TRAIN PERSONNEL WHO WILL OPERATE THIS MACHINE.
  • Page 10 WARNING Make sure all labels, decals, warnings, cautions and instructions are fastened to the machine. Purchase new labels and decals from American-Lincoln. WARNING The operator must exhibit extreme caution when negotiating, turning, and traveling across grades or ramps.

  • Page 11: Machine Information/Preparation

    MACHINE INFORMATION/PREPARATION TOWING THE SCRUBBER NOTE: The scrubber must only be towed for short distances. For example, from inside a building to the outside. It must never be towed for long distances on the road in heavy traffi c. NOTE: To transport the scrubber, load it, complete with its four tires, onto a truck. Should it be necessary to tow the scrubber, use a strong chain.
  • Page 12 -Rear Wheel Nuts for Tightness NEW HOLLAND TN60 TRACTOR POWER UNIT The American-Lincoln SR9772 utilizes a NEW HOLLAND TN60 as the power unit. The power unit provides hydraulic power for the brush drive, squeegee, solution vacuum, brush position and squeegee position functions.

  • Page 13: Scrubber Operation

    SCRUBBER OPERATION CHECKS BEFORE USING THE SCRUBBER Before using the scrubber, make sure you are familiar with the position and function of all controls. Ensure the maintenance and lubrication operations described in the NEW HOLLAND manual have been carried out, followed by a visual inspection of the outside of the scrubber.
  • Page 14 CAUTION When SHIFTING from one range to another, forward to reverse, or reverse to forward, the operator MUST reduce the speed (throttle) to LOW IDLE, shift range and/or gear, then increase the speed (throttle). American-Lincoln 1-13 SR9772...

  • Page 15: The Scrubbing Systems

    THE SCRUBBING SYSTEMS SOLUTION RECOVERY TANK TANK FILTER STRAINER SCRUB SQUEEGEE BRUSH P4759 FLOOR CONTACT WITHOUT CAMEL SYSTEM HOW IT WORKS (Without Camel System) During the scrubbing process, a solution of detergent and water from the solution tanks is fed through the solution lines where it is disbursed to the fl...
  • Page 16 In the separator, solids are removed and purged into the containment chamber. The solids-free solution is then fed up through the separator outlet and into the solution tank where it is ready to be mixed with fresh, metered detergent, allowing the cleaning process to continue. American-Lincoln 1-15 SR9772...

  • Page 17: Operating The Scrubber Controls

    OPERATING THE SCRUBBER CONTROLS Solution Flow Knob - To control fl ow of water to scrub deck brushes once the scrub deck switch is engaged, rotate knob clockwise from the OFF position shown. Solution fl ow can be controlled from 0 GPM (OFF position) to 6.0 GPM in the full ON position (approximately 115º...
  • Page 18 Prior to engaging any of the switches on the control panel, the tractor’s hydraulic lever must be engaged by pulling it back. During transport, make sure the scrub deck and squeegee are in the raised position and the tractor hydraulic lever is in the FORWARD/OFF position. American-Lincoln 1-17 SR9772...

  • Page 19: Operating Instructions

    OPERATING INSTRUCTIONS NORMAL SCRUBBING MODE Operating Instructions: Access the scrubber. Check all the scrubbing system controls, verifying they are in the off position. Confi rm the hydraulic control lever is in the off position (all the way forward). CONTROL PANEL Follow the New Holland operations manual for start-up.
  • Page 20 MUST reduce the speed (throttle) to LOW IDLE, shift range and/or gear, then increase the speed (throttle). 21. Adjust the water fl ow by turning the solution fl ow knob located on control panel to optimize scrubbing performance. SOLUTION FLOW KNOB American-Lincoln 1-19 SR9772...
  • Page 21 OPERATING INSTRUCTIONS 22. Inspect the scrub path verifying the scrub performance and solution recovery. 23. Continue scrubbing and monitoring the scrub path for maximum performance. 24. Warning lights on the scrubber control panel for low solution or high recovery will illuminate when the solution level is low or the recovery tank is full.
  • Page 22 Press and hold switch in upward position for 2 seconds and release, the switch will return automatically to a neutral position. Confi rm the scrub deck and squeegees are in the raised position. Push the hydraulic control lever foward to off/de-energize position. American-Lincoln 1-21 SR9772...
  • Page 23 OPERATING INSTRUCTIONS Move the scrubber to fi lling station by fi rst reducing the throttle to low idle following start-up, depress clutch, select range and gear, slowly release clutch and increase throttle. CAUTION When SHIFTING from one range to another, forward to reverse, or reverse to forward, the operator MUST reduce the speed (throttle) to LOW IDLE, shift range and/or gear, then increase the speed (throttle).
  • Page 24 40. Lower drain hoses on rear of unit to direct recovered fl uid to appropriate dump location. 41. Remove drain plug. 42. Once the recovery tank is drained, open the clean out doors by loosening knobs and pivoting the “t” bolts. American-Lincoln 1-23 SR9772...
  • Page 25 OPERATING INSTRUCTIONS 43. Flush out the tanks, removing all sediment and debris from tank bottoms of all three compartments. Rinse doors and seals to remove all debris and ensure proper sealing. CLEAN OUT DOOR 44. Once the tanks are clean close doors, pivot “t” bolts and tighten knobs to seal the tanks. 45.
  • Page 26 -Clean the recovery tank’s screen and fl oat. -Check vacuum pipes and hoses for obstructions. -Check the slash skirt for wear, damage, or adjustment. -Check the outlet strainers in the solution tanks for contamination. -Fill fuel tank (Diesel only) -Check for leaks American-Lincoln 1-25 SR9772...
  • Page 27 OPERATING INSTRUCTIONS TO CLEAN THE SOLUTION TANKS Follow these instructions to clean the solution tanks after every scrubbing cycle: -Inspect, remove, and clean the solution inlet fi lter on the bottom of the left hand and right hand tanks. -Flush the sediment accumulations from the fl oor of the tanks. TO CLEAN THE RECOVERY TANK Follow these instructions to clean the recovery tank after every scrubbing cycle: -Position a corner of the machine near a fl...

  • Page 28: Service Chart

    SERVICE CHART For service assistance, consult your factory-authorized American-Lincoln dealer. For best performance, replace worn scrubbing system parts with genuine American-Lincoln parts. REFERENCE NEW HOLLAND MANUAL FOR ALL TRACTOR MAINTENANCE/ SERVICE DETAILS. EVERY 8 HOURS or DAILY Operation Checklist (Clean/adjust if necessary)

  • Page 29: Service Instructions

    SERVICE INSTRUCTIONS BRUSH PRESSURE AND BRUSH WEAR Factors affecting brush wear are type of bristle, bristle, area, and COUNTERBALANCE load on the bristles. See your authorized distributor for the type SPRINGS of brush and bristle most suitable. Brush pressure may be adjusted by adding or removing counterbalance springs.
  • Page 30 Before starting the scrubber make sure that there is enough fuel in the tank. The fuel nozzle is located on the front of the scrubber to the left side under the fender. Fuel up regularly to prevent the engine stalling and interruption of cleaning cycle. Add the appropriate fuel, refer to New Holland manual. FILL FUEL TANK American-Lincoln 1-29 SR9772...
  • Page 31 SERVICE INSTRUCTIONS FUSES Fuses are easily accessible by removing the panel. Replace blown fuse with the same size fuse to prevent damage to the electrical circuit. FUSES FUSES SOLUTION FEED HOSES To check solution hoses for damage remove cover by unscrewing the nut on the side of the cover. Clean and check hoses for cracks or leaks.
  • Page 32 Open turbine cover, loosen bolts, tighten adjusting nut to increase tension (proper setting is 1/2” defl ection of the belt with 25 lbs. of pressure at midpoint between the two pulleys), then re-tighten bolts. SPLASH SKIRT ADJUSTMENT Adjust the right and left side skirts with brush wear to maintain minimal fl oor clearance. American-Lincoln 1-31 SR9772...
  • Page 33 SERVICE INSTRUCTIONS SCREEN RECOVERY TANK SERVICING THE RECOVERY TANK When the tank is full (9” from top), the red indicator light is activated on the console. At a height of 8” from the top of the tank, the vacuum air fl ow to the squeegees will automatically shut off. On the camel system inspect, remove and clean inlet screens on the bottom of the recovery tank.
  • Page 34 Run engine at 2000 rpm. Place vacuum gauge on other inlet pipe and check reading. To adjust relief valve setting: Hold the stem to keep it from turning. Turn the locknut clockwise to increase the setting; counterclockwise to decrease the setting. American-Lincoln 1-33 SR9772...

  • Page 35: Troubleshooting - Scrubbing System

    TROUBLESHOOTING - SCRUBBING SYSTEMS TROUBLESHOOTING - SCRUBBING SYSTEM PROBABLE CAUSE PROBLEM REMEDY Poor scrubbing action 1. Worn scrubbing brushes 1. Inspect brushes. If brushes are worn to ½" or less, replace all 4 brushes 2. Incorrect method of operation 2. Check scrubbing procedure, brush pressure, type of brush solution flow &...

  • Page 36: Troubleshooting - Hydraulic System

    2. Adjust contact location. 2. Switch contact lever up) Failure to lower with shift 1. No power to control panel 1. Check electrical connection and fuse. lever in forward gears 2. Incorrect switch position 2. Actuate system. (control lever down) American-Lincoln 1-35 SR9772...

  • Page 37: Troubleshooting - Camel Recycling Pump

    TROUBLESHOOTING - CAMEL RECYCLING PUMP TROUBLESHOOTING CHART - CAMEL RECYCLING PUMP SUCTION ROTOR PORT STATOR DISCHARGE PORT PACKING BALL BEARING FLEXIBLE JOINT GLAND PROBABLE CAUSE REMEDY PROBLEM 1. Tighten set screw on coupling Failure to pump 1. Coupling slip 2. Possible excessive pressure. Replace 2.

  • Page 38: Troubleshooting - Camel Detergent Pump

    1. Clean out detergent lines 1. Restricted or blocked detergent lines Motor operates, but pump 2. Replace wiring or motor 2. Defective wiring or motor output is low or stopped 3. Check fluid level 3. Fluid level low or empty American-Lincoln 1-37 SR9772...

  • Page 39: Ordering Parts

    Parts may be ordered from American-Lincoln authorized distributors. Parts may be ordered from American-Lincoln authorized distributors. Record the information from the American-Lincoln serial plate to avoid Record the information from the American-Lincoln serial plate to avoid delays in filling your order: delays in filling your order: Serial No.:...
  • Page 40 Hydraulic Motor Hoses & Fittings ..........................2-32 Brush Drive Motors & Fittings ............................2-33 Control Panel Assembly ............................2-34 Decals ..................................2-36 Scrub Deck Hydraulics & Fittings ..........................2-38 Scrub Deck Flap Assemblies .............................2-40 Hydraulic Schematic ..............................2-41 Electrical Schematic ..............................2-42 American-Lincoln FORM NO. 28600313 - 2-1 SR9772...

  • Page 41: Mounting Structure

    MOUNTING STRUCTURE 2-2 - FORM NO. 28600313 American-Lincoln SR9772...
  • Page 42 Washer, Flat, .875 x .375 x .060 2-95-04182 Hex Nut, 3/8-16 Stop 7-13-07104 Clamp, Hose Bolt, M-14 2-00-05810 Lock Nut, M-18 x 1.5 Lock Washer, M-18 Bolt, 18mm x 50 7-75-01229 Spacer (Cab Version only) American-Lincoln FORM NO. 28600313 - 2-3 SR9772...

  • Page 43: Scrub Deck/Solution Control

    SCRUB DECK 2-4 - FORM NO. 28600313 American-Lincoln SR9772...
  • Page 44 Fitting, 1/2” NPT x 5/8” Hose Barbed, 90º 2-00-05805 Fitting, 1/2” NPT x 3/4” Hose Barbed, Str. 7-25-02012 Fitting, 3/4” NPT x 3/4” Barbed 7-33-02559 Hose, 3/4” ID Heater 7-33-02559 Hose, 3/4” ID Heater 2-00-02220 Clamp, Hose American-Lincoln FORM NO. 28600313 - 2-5 SR9772...

  • Page 45: Scrub Deck Lift (No Cab)

    SCRUB DECK LIFT (NO CAB) 2-6 - FORM NO. 28600313 American-Lincoln SR9772...
  • Page 46 Bolt, 1/2-20 x 4.50” 2-00-05043 Washer, Plain 25/64 ID x 3/4 OD 2-00-04950 Bolt, 12mm x 1.25 x 45mm 8-76-00041 Spring, Counterbalance 7-13-05079 Chain, Scrub Deck Lift 2-00-05054 Fitting, 9/16-18 to 3/8-18 Adapter American-Lincoln FORM NO. 28600313 - 2-7 SR9772...

  • Page 47: Scrub Deck Lift (Cab)

    SCRUB DECK LIFT (CAB) C0957d CAB/0903 2-8 - FORM NO. 28600313 American-Lincoln SR9772...
  • Page 48 Washer, Plain 25/64 ID x 3/4 OD 2-00-05946 Bolt, 12mm x 1.25 x 70mm 8-76-00041 Spring, Counterbalance 7-13-05079 Chain, Scrub Deck Lift 2-00-05054 Fitting, 9/16-18 to 3/8-18 Adapter 7-75-01244 Spacer 2-00-03589 Collar, Setscrew American-Lincoln FORM NO. 28600313 - 2-9 SR9772...

  • Page 49: Squeegees/Squeegee Lift

    SQUEEGEES/SQUEEGEE LIFT 2-10 - FORM NO. 28600313 American-Lincoln SR9772...
  • Page 50 Cylinder, Squeegee Lift 2-00-00405 Flat Washer, 1.063 x .531 x .094 2-00-00242 Bolt, 1/2-13 x 2.0 2-00-04936 Lock Nut, 1/2-13 Elastic 2-00-00234 Screw, 3/8-16 x 1.5 HHC Squeegee Vac Hose/Clamps: 7-33-02381 / 7-13-07104 American-Lincoln FORM NO. 28600313 - 2-11 SR9772...
  • Page 51 SOLUTION TANKS SEE CLEANOUT DOOR COMPONENTS (ITEMS 28 - 31) C0956gasket/5-05 2-12 - FORM NO. 28600313 American-Lincoln SR9772...

  • Page 52: L.h. Solution Tank

    Screw, 1/4-20 x .50 Long 2-00-05949 Set Screw, 1/2-13 x .50, Oval Point, SS Cleanout Door Assembly: 7-19-08088 Cleanout Door 7-29-00334 Gasket, Cleanout Door 7-41-00054 Latch, Cleanout Door 2-00-00009 Screw, 8-32 x 1.2 FHS American-Lincoln FORM NO. 28600313 - 2-13 SR9772...

  • Page 53: Solution Vacuum System

    SOLUTION VACUUM 2-14 - FORM NO. 28600313 American-Lincoln SR9772...

  • Page 54: Solution Vacuum System

    2-00-00644 Hex Nut, Fiber Insert 5/16-18 3-73-00056 Gasket, Bulk, Adhesive Back (use as needed) 2-00-02597 Screw, Hex Head, 5/16-18 x 3.25” 2-00-00530 Lock Washer, 5/16” 2-00-00585 Hex Nut, 5/16-18 7-08-01122 Bracket, Prop Rod American-Lincoln FORM NO. 28600313 - 2-15 SR9772...

  • Page 55: Solution Vac/Washer Hose (Cab)

    SOLUTION VAC/WASHER HOSE (CAB ONLY) 2-16 - FORM NO. 28600313 American-Lincoln SR9772...

  • Page 56: Solution Vac/Washer Hose (Cab)

    Bracket, Washer Solution Hose 839401 Valve, Drain 833901 Handle, Drain Valve 833407 Gasket, Drain 52206A Chain, Cover Autoscrubber 962987 Screw, 10-24 x 3/8 PN ST TYP23 7-33-02409 Hose, Solution Drain 2-00-02220 Clamp, Hose American-Lincoln FORM NO. 28600313 - 2-17 SR9772...

  • Page 57: Recovery Tank

    RECOVERY TANKS revised 6/07 2-18 - FORM NO. 28600313 American-Lincoln SR9772...
  • Page 58 Screw, 1/2-13 X 2.00 Hhc 7-19-08090 Cleanout Door Assy (39-42) Cleanout Door Assembly: 7-19-08088 Cleanout Door 7-29-00334 Gasket, Cleanout Door 2-00-00009 Screw, 8-32 x 1.2 FHS 7-41-00054 Latch, Cleanout Door = Revised or new since last update American-Lincoln FORM NO. 28600313 - 2-19 SR9772...

  • Page 59: Recovery Tank Lid

    RECOVERY TANK LID 2-20 - FORM NO. 28600313 American-Lincoln SR9772...

  • Page 60: Recovery Tank Lid

    Cap, Spring 7-10-04006 Cage, Float 7-26-04009 Float, 4” Dia. 2-00-03702 Washer, .625 x .281 x .063 2-00-00251 Screw, 1/4-20 x .50 2-00-00641 Nut, 1/4-20 Elastic Stop 2-95-02554 Fitting, 2” NPT x 3.0” Half Nipple American-Lincoln FORM NO. 28600313 - 2-21 SR9772...

  • Page 61: Camel Recovery Tank

    CAMEL OPTION/RECOVERY TANK revised 6/07 2-22 - FORM NO. 28600313 American-Lincoln SR9772...

  • Page 62: Camel Recovery Tank

    Clamp, Hose, Witteck #10P 7-33-02570 Hose, 3/4” ID x 60” Long 7-33-02598 Hose-Solution Feed 2-00-00644 Nut, Hex, Insert Fiber, 5/16-18 7-33-02487 Sleeve, 11” 7-83-04222 Tank, Recovery, Weldt = Revised or new since last update American-Lincoln FORM NO. 28600313 - 2-23 SR9772...

  • Page 63: Camel Pump Group

    CAMEL OPTION/PUMP GROUP 71502-1revC 2-24 - FORM NO. 28600313 American-Lincoln SR9772...
  • Page 64 Hose, -8 ORS STR. x 90º (113.5” long) 7-33-02555 Hose, -8 ORS STR. x 90º (116” long) 2-00-03407 Clamp, Hose, Witteck #10P 2-00-00281 Set Screw, 8-32 x 1/2 2-00-00287 Set Screw, 1/4-20 x 1/2 American-Lincoln FORM NO. 28600313 - 2-25 SR9772...

  • Page 65: Camel Detergent Tank (Non-Cab)

    CAMEL DETERGENT TANK (NON-CAB) 71502-3revC 2-26 - FORM NO. 28600313 American-Lincoln SR9772...
  • Page 66 2-00-02310 Lock Washer, 3/8” Helical Spring 2-00-00233 Bolt, Hex Head, 3/8-16 x 1.00 Finished 2-00-01803 Washer 2-00-05041 Lock Washer, M8 Helical Spring 2-00-05412 Reducer Connection 2-00-05947 Fitting, Elbow 7-33-02686 Hose 7-13-07084 Clamp, Hose American-Lincoln FORM NO. 28600313 - 2-27 SR9772...

  • Page 67: Camel Detergent Tank (Cab)

    CAMEL DETERGENT TANK (CAB) 71502-2revB 2-28 - FORM NO. 28600313 American-Lincoln SR9772...
  • Page 68 Bolt, Hex Head, 3/8-16 x 1.00 Finished 2-00-01803 Washer 2-00-04949 Screw, M8 x 1.25 x 45mm 2-00-05821 Nut, M8 x 1.25 Elastic Stop 2-00-05412 Reducer Connection 2-00-05947 Fitting, Elbow 7-13-07084 Clamp, Hose 7-33-02686 Hose American-Lincoln FORM NO. 28600313 - 2-29 SR9772...

  • Page 69: Hydraulic Manifold Valve

    Fitting, -12 SAE x -8 SAE, Reducer Bushing 2-00-04924 Fitting, 3/4-16 x 3/16-16 Tee (Camel only) 2-00-04975 Fitting, 8 SAE Elbow, 45º (Camel only) 2-00-02310 Lock Washer, 3/8” Helical Spring 2-00-04705 Bolt, 3/8-16 x 1.25 LG Finished Hex Head 2-30 - FORM NO. 28600313 American-Lincoln SR9772...
  • Page 70 Cylinder, Hydraulic 2-00-05054 Fitting, 9/16-18 to 3/8-18 Adapter Tractor Pump Block 2-00-05801 Fitting, -12 ORS x 22mm SAE Str. 2-00-05282 Fitting, -12 ORS x -4 ORS, Reducer 2-00-05270 Fitting. -12 ORS Reducer Nut American-Lincoln FORM NO. 28600313 - 2-31 SR9772...

  • Page 71: Hydraulic Motors, Hoses & Fittings

    Description 0782-158 Motor, Hydraulic 0782-128 Motor, Hydraulic 2-00-04885 Fitting, 90º Elbow (O-Ring) 2-00-04970 Fitting, Str., -8 ORS x -8 SAE 2-00-05195 Fitting, -8 ORS x 3/8 NPT Str. 2-00-04892 Fitting, 90º Elbow (O-Ring) 2-32 - FORM NO. 28600313 American-Lincoln SR9772...

  • Page 72: Brush Drive Motors & Fittings

    BRUSH DRIVE MOTORS & FITTINGS Item Ref. No. Description 0782-150 Motor, Brush Drive 2-00-05802 Fitting, -8 ORS Bulkhead, Str. 2-00-04921 Fitting, 10 SAE 90º -8 ORS 2-00-04974 Fitting, #8 ORS to #10 SAE Connector American-Lincoln FORM NO. 28600313 - 2-33 SR9772...

  • Page 73: Control Panel Assembly

    CONTROL PANEL ASSEMBLY revised 6/07 NOTE: FOR NONCAMEL MACHINES REMOVE ITEMS #11 & #20 AND REPLACE WITH AN ADDITIONAL #12. REMOVE ITEMS #7 & #21. 2-34 - FORM NO. 28600313 American-Lincoln SR9772...
  • Page 74 Actuator, Recycle On/Off 2-00-05798 Knob, Rheostat 2-00-03062 Screw, 10-24 x 5/8 2-00-01372 Nut, 8-32 Fiber Lock 7-64-00021 Timer 2-00-00039 Screw, 10-24 2-00-01246 Nut, 10-24 Elastic Stop = Revised or new since last update American-Lincoln FORM NO. 28600313 - 2-35 SR9772...

  • Page 75: Decals

    DECALS 2-36 - FORM NO. 28600313 American-Lincoln SR9772...
  • Page 76 Instrument Panel 8-18-00543 SR9772 8-18-00564 American -Lincoln (LH on Holland TN60) was 8-18-00545 ( for Holland TN55) 8-18-00563 American-Lincoln (RH on Holland TN60) was 8-18-00544 (RH on Holland TN55) 8-18-00553 American-Lincoln (Large black/gray) 8-18-00554 American-Lincoln (Medium black/gray) Serial Number Plate...

  • Page 77: Scrub Deck Hydraulics & Fittings

    SCRUB DECK HYDRAULICS & FITTINGS 71521-2revE 2-38 - FORM NO. 28600313 American-Lincoln SR9772...
  • Page 78 Hose, -8 ORS, STR x 90, 113.5” long NOTE #1 7-33-02555 Hose, -8 ORS, STR x 90, 116” long NOTE #1 7-33-02601 Hose, #8 STR, 23” long NOTE #1: Not part of Hose Kit 0760-673 American-Lincoln FORM NO. 28600313 - 2-39 SR9772...

  • Page 79: Scrub Deck Flap Assemblies

    SCRUB DECK FLAP ASSEMBLIES LEFTHAND 7-25-08097 RIGHTHAND 7-25-08098 Item Ref. No. Description 7-32-03023 Holder, Flap, LH 7-32-03025 Holder, Flap, RH 7-25-08096 Flap, Side 2-00-04811 Rivet, 1/4” Blind 2-00-00466 Flat Washer, .625 x .203 x .031 2-40 - FORM NO. 28600313 American-Lincoln SR9772...

  • Page 80: Hydraulic Schematic

    HYDRAULIC SCHEMATIC American-Lincoln FORM NO. 28600313 - 2-41 SR9772...

  • Page 81: Electrical Schematic

    ELECTRICAL SCHEMATIC 2-42 - FORM NO. 28600313 American-Lincoln SR9772...
  • Page 82 TABLE OF CONTENTS - CHAPTER 3 - OPTIONS Brush Options ................................3-2 Foam-Filled Tires Option ............................3-3 Catalytic Muffl er Option .............................3-4 Rotating Light Option (ROLL-BAR) ...........................3-5 Warning Light Option (CAB) ............................3-6 Vacuum Wand Option ..............................3-7 Transmission Lock-Out Option ..........................3-8 Additional Options ..............................3-9 American-Lincoln SR9772...

  • Page 83: Brush Options

    Plate, Brush Mounting Sectional Brushes (plastic back) 7-08-03192 Bassine 7-08-03193 Straight Wire 7-08-03194 Nylon (Black) 7-08-03195 Amerfi l (.025) 7-08-03196 Amerfi l (.040) 7-08-03197 Amergrit 2-00-00594 Nut, Hex 1/4 - 20 2-00-02706 Screw, ¼ - 20 x 1.00 HHM American-Lincoln SR9772...

  • Page 84: Foam-Filled Tires Option

    FOAM FILLED TIRES OPTION OPTION NO. 0780-550 Item Ref. No. Description 0797-050 Foam Filled Front Tire 0797-021 Foam Filled Rear Tire American-Lincoln SR9772...

  • Page 85: Catalytic Muffl Er Option

    CATALYTIC MUFFLER OPTION OPTION NO. 0780-531 American-Lincoln SR9772...

  • Page 86: Rotating Light Option (Roll Bar)

    OPTION NOS. 0780-533 (RED) & 0780-536 (AMBER) Item Ref. No. Description 7-08-02034 Bracket, Warning Light, Roll Bar 8-40-05033 Warning Light, Revolving (RED) 8-40-05039 Warning Light, Revolving (AMBER) 2-00-00491 Grommet 2-00-00605 Hex Nut, 10-24 2-00-00518 Lock Washer, 1/4” Helical Spring 2-00-00251 Screw, 1/4-20 x .50 American-Lincoln SR9772...

  • Page 87: Warning Light Option (Cab)

    OPTION NOS. 0780-535 (RED) & 0780-538 (AMBER) Item Ref. No. Description 8-89-07600 Support, Warning Light 8-40-05033 Warning Light, Revolving (RED) 8-40-05039 Warning Light, Revolving (AMBER) 2-00-00605 Hex Nut, #10-24 2-00-00491 Grommet 2-00-05823 Screw, M6 x 1.0 x 55mm Pan Head 7-09-01062 Spacer American-Lincoln SR9772...

  • Page 88: Vacuum Wand Option

    OPTION NO. 0780-539 Item Ref. No. Description 7-13-07097 Clip, Tool 639804 Wand Assembly 638824 Tool Assembly 7-33-02213 Hose, Vacuum 2-00-05905 Spacer 7-03-00040 Adapter, 3” OD - 1.5” OD 2-00-04312 Screw, 10-24 x .63 HWH 7-13-07225 Clamp, Over-Center Hose, 3” American-Lincoln SR9772...

  • Page 89: Transmission Lock-Out Option

    TRANSMAISSION LOCK-OUT OPTION 0780-540revB OPTION NO. 0780-540 Item Ref. No. Description 7-08-02037 Bracket, Transmission Lock-Out 2-00-05315 Screw, Self-Drill 1/4-14 X .1.00 LG 7-58-05357 Plate, Transmission Lockout 7-58-05358 Bracket, Transmission Lockout American-Lincoln SR9772...

  • Page 90: Additional Options

    ADDITIONAL OPTIONS revised 6/07 Item Ref. No. Description Options 56109256 High Temp, Low Pressure Option = Revised or new since last update American-Lincoln SR9772...
  • Page 91 14600 21 Avenue North Plymouth, MN 55447-3408 www.americanlincoln.com Phone: 800-331-7692 Fax: 877-877-2586 ©2007 American-Lincoln...

This manual is also suitable for:

Sr9772 510-017Sr9772 510-015Sr9772 510-018

Table of Contents